The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the common rail injection system is controlled.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0335 | Crankshaft Position Sensor "A" Circuit | When one of the following conditions is met: (1 trip detection logic)
·
No crankshaft position sensor signal to ECM while cranking
·
When normal G signal is input, malfunctioning NE signal is input
·
No crankshaft position sensor signal to ECM at engine speed of 600 rpm or more |
·
Open or short in crankshaft position sensor circuit
·
Crankshaft position sensor
·
Crankshaft
·
ECM |
Comes on | DTC stored |
| P0339 | Crankshaft Position Sensor "A" Circuit Intermittent | No crankshaft position sensor signal is input to ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met: (1 trip detection logic) (a) Engine speed is at 1000 rpm or more (b) STA signal is off (c) 3 seconds or more have elapsed after STA signal is switched from on to off. |
·
Open or short in crankshaft position sensor circuit
·
Crankshaft position sensor
·
Crankshaft
·
ECM |
- | DTC stored |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0335 | Crank or start engine |
| P0339 | Engine running at 1000 rpm or more with vehicle stationary |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
The Data List item Engine Speed is calculated from the output of the crankshaft position sensor.
A DTC is also stored when the ground of a shielded wire is faulty.
Inspect the crankshaft position sensor.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C42-1 (NE+) - C39-78 (NE+) | Always | Below 1 Ω |
| C42-2 (NE-) - C39-77 (NE-) | Always | Below 1 Ω |
| C42-3 (GND) - Body ground | Always | Below 1 Ω |
| C42-1 (NE+) or C39-78 (NE+) - Body ground | Always | 10 kΩ or higher |
| C42-2 (NE-) or C39-77 (NE-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the sensor installation.
Sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the teeth of the sensor plate.
The sensor plate's teeth do not have any cracks or deformation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG