Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2019.09
RM25T0E _58 Vehicle Interior _029927 METER / GAUGE / DISPLAY _0137559 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

w/ VSC


In this circuit, the combination meter assembly receives engine speed signals from the ECM via the CAN communication system. The combination meter assembly displays the engine speed calculated based on the data received from the ECM.


w/o VSC


The combination meter receives revolution signals from the ECM*1, emission control ECU*2 or pickup sensor*3. The combination meter displays engine speed data that is calculated based on the data received from the ECM*1, emission control ECU*2 or pickup sensor*3.

*1: for 1GR-FE, 1VD-FTV

*2: for 1HZ (w/ EGR System)

*3: for 1HZ (w/o EGR System)



WIRING DIAGRAM

E255800C01
4.677,2.563 6.896,2.813 2.219,0.25 10 false Combination Meter Assembly 1.708,2.573 3.938,3.021 2.229,0.448 10 false ECM 0.802,3.375 3.563,3.656 2.76,0.281 10 false : CAN Communication Line 0.156,0.146 2.375,0.396 2.219,0.25 12 false w/ VSC:

E224935E25
4.885,1.865 6.604,2.073 1.719,0.208 10 false L25 4.875,2.01 6.073,2.333 1.198,0.323 10 false Combination Meter Assembly 5.094,1.063 6.813,1.271 1.719,0.208 10 false S 4.813,0.948 6.531,1.156 1.719,0.208 10 false 10 2.188,0.958 3.906,1.167 1.719,0.208 10 false 15 1.719,1.073 3.438,1.281 1.719,0.208 10 false TACH 1.417,1.865 3.073,2.167 1.656,0.302 10 false A29 1.417,2.01 3.385,2.323 1.969,0.313 10 false ECM 0.125,0.104 2.115,0.521 1.99,0.417 12 false for 1VD-FTV (w/o VSC):

E224935E23
4.885,1.865 6.604,2.073 1.719,0.208 10 false L25 4.875,2.01 6.073,2.333 1.198,0.323 10 false Combination Meter Assembly 5.094,1.063 6.813,1.271 1.719,0.208 10 false S 4.813,0.948 6.531,1.156 1.719,0.208 10 false 10 2.188,0.958 3.906,1.167 1.719,0.208 10 false 15 1.719,1.073 3.438,1.281 1.719,0.208 10 false TACH 1.417,1.865 3.073,2.167 1.656,0.302 10 false I84*1, A29*2 1.417,2.01 3.385,2.323 1.969,0.313 10 false ECM 0.125,0.104 2.115,0.521 1.99,0.417 12 false for 1GR-FE (w/o VSC): 0.26,2.063 2.229,2.375 1.969,0.313 10 false *1: for LHD 0.281,2.375 2.25,2.688 1.969,0.313 10 false *2: for RHD

E295958E02
2.833,1.667 4.125,2.031 1.292,0.365 10 false C83 2.844,1.823 4.135,2.188 1.292,0.365 10 false Pickup Sensor*1 2.563,1.167 3.854,1.531 1.292,0.365 10 false 2 3.875,1.167 5.167,1.531 1.292,0.365 10 false 1 2.75,1.104 4.042,1.469 1.292,0.365 10 false NE- 3.583,1.104 4.875,1.469 1.292,0.365 10 false NE 5.531,1.146 6.823,1.51 1.292,0.365 10 false 10 5.792,1.24 7.083,1.604 1.292,0.365 10 false S 5.615,2.073 6.802,2.438 1.188,0.365 10 false L25 5.604,2.219 6.792,2.583 1.188,0.365 10 false Combination Meter Assembly 2.792,3.198 4.292,3.583 1.5,0.385 10 false A31 2.792,3.344 4.365,3.719 1.573,0.375 10 false Emission Control ECU*2 3.51,2.76 5.01,3.146 1.5,0.385 10 false TAC 3.875,2.635 5.375,3.021 1.5,0.385 10 false 6 0.135,0.146 1.427,0.51 1.292,0.365 12 false for 1HZ: 0.24,3.01 1.885,3.24 1.646,0.229 10 false *1: w/o EGR System 0.24,3.333 1.885,3.563 1.646,0.229 10 false *2: w/ EGR System

PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ VSC A
for 1GR-FE (w/o VSC), 1VD-FTV (w/o VSC) B
for 1HZ (w/o EGR System) C
for 1HZ (w/ EGR System) D



A

2.CHECK FOR DTC

B

5.CHECK COMBINATION METER ASSEMBLY

C

7.INSPECT PICKUP SENSOR

D

9.CHECK COMBINATION METER ASSEMBLY
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

3.CHECK FOR DTC
a.

Check for DTCs.

for 1VD-FTV, w/ DPF:

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR

for 1VD-FTV, w/o EGR System:

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>DTC CHECK / CLEAR

for 1GR-FE:

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 61
OK:

No DTCs are output.



Result:
Proceed to
OK
NG (for 1VD-FTV)
NG (for 1GR-FE)



OK

4.PERFORM ACTIVE TEST USING GTS (TACHOMETER OPERATION)

NG (for 1VD-FTV)

NG (for 1GR-FE)

4.PERFORM ACTIVE TEST USING GTS (TACHOMETER OPERATION)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TachoMeter Operation Tachometer OFF, 0, 1000, 2000, 3000, 4000, 5000 or 6000 (rpm) -
Body Electrical > Combination Meter > Active Test
Tester Display
TachoMeter Operation
50004 122 2
OK:

Tachometer indication is normal.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY

5.CHECK COMBINATION METER ASSEMBLY
a.
E293691C02
0.177,1.115 0.667,1.354 0.49,0.24 0.667,0.792 0.823,0.792 0.823,0.792 1.302,1.208 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.104,2.417 0.417,2.573 0.313,0.156 10 false *b 2.719,3.469 3.063,3.667 0.344,0.198 10 false GND 0.542,0.719 0.885,0.917 0.344,0.198 10 false S 0.313,1.146 0.656,1.344 0.344,0.198 10 false L25
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Using an oscilloscope, check the signal waveform of the meter.

Measurement Condition
Item Content
Tester Connection L25-10 (S) - Body ground
Tool Setting 5 V/DIV., 10 msec./DIV.
Condition Engine idling

OK:

The waveform displayed is as shown in the illustration.


HINT:

As the engine speed increases, the wavelength shortens.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the L25 combination meter assembly connector.


b.

Disconnect the A29*1 or I84*2 ECM connector.

*1: for 1GR-FE (for RHD), 1VD-FTV (w/o VSC)

*2: for 1GR-FE (for LHD)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE (for RHD), 1VD-FTV (w/o VSC)
Tester Connection Condition Specified Condition
L25-10 (S) - A29-15 (TACH) Always Below 1 Ω
L25-10 (S) or A29-15 (TACH) - Body ground Always 10 kΩ or higher

for 1GR-FE (for LHD)
Tester Connection Condition Specified Condition
L25-10 (S) - I84-15 (TACH) Always Below 1 Ω
L25-10 (S) or I84-15 (TACH) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT PICKUP SENSOR


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (PICKUP SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

8.CHECK HARNESS AND CONNECTOR (PICKUP SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the C83 pickup sensor connector.


b.

Disconnect the L25 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C83-1 (NE) - L25-10 (S) Always Below 1 Ω
C83-2 (NE-) - Body ground Always Below 1 Ω
C83-1 (NE) or L25-10 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK COMBINATION METER ASSEMBLY
a.
E295959C02
0.198,1.135 0.677,1.385 0.479,0.25 0.625,0.792 0.823,0.792 0.823,0.792 1.313,1.24 true 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 0.115,2.458 0.427,2.615 0.313,0.156 10 false *b 2.75,3.302 3.188,3.531 0.438,0.229 10 false GND 0.49,0.698 0.927,0.927 0.438,0.229 10 false S 0.313,1.167 0.75,1.396 0.438,0.229 10 false L25
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Using an oscilloscope, check the signal waveform of the meter.

Measurement Condition
Item Content
Tester Connection L25-10 (S) - Body ground
Tool Setting 0.2 V/DIV., 10 msec./DIV.
Condition Engine idling

OK:

The waveform displayed is as shown in the illustration.


HINT:

As the engine speed increases, the wavelength shortens.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EMISSION CONTROL ECU)
10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EMISSION CONTROL ECU)
a.

Disconnect the L25 combination meter assembly connector.


b.

Disconnect the A31 emission control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-10 (S) - A31-6 (TAC) Always Below 1 Ω
L25-10 (S) or A31-6 (TAC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR