Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2022.09
RM25T0E _59 Vehicle Exterior _029935 WINDOW / GLASS _0137657 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

w/ Front Camera:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a TOYOTA genuine part. If a non-TOYOTA genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also the front camera system and pre-collision system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 56111 1.CLEAN WINDSHIELD GLASS

a.

Using a scraper, remove the damaged stoppers, and adhesive sticking to the windshield glass.


b.

Clean the outer circumference of the glass with non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Be careful not to damage the glass.

·

Even if using new glass, clean the glass with non-residue solvent.




Hide 56114A 2.INSTALL BACK WINDOW GLASS RETAINER

a.

Apply the body primer to the body where the retainers will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.



b.
B231539C02
1.281,0.896 1.49,0.479 1.49,0.479 1.667,0.479 true 2.563,1.271 2.563,0.656 2.563,0.656 2.719,0.656 true 0.802,1.063 0.802,0.563 0.802,0.563 0.646,0.563 true 1.594,1.302 1.594,1.781 false 0.76,1.438 0.938,1.615 0.177,0.177 10 false a 2.396,1.635 2.573,1.813 0.177,0.177 10 false a 1.698,0.417 2.01,0.573 0.313,0.156 10 false *1 2.75,0.583 3.063,0.74 0.313,0.156 10 false *a 1.542,1.802 1.854,1.958 0.313,0.156 10 false *b 0.469,0.479 0.781,0.677 0.313,0.198 10 false *a
*1 Back Window Glass Retainer
*a R End
*b Align with the edge of vehicle body


Remove the peeling paper from 2 new back window glass retainers. Install the 2 back window glass retainers to the vehicle body at the locations shown in the illustration.

Standard:
Area Specified Condition
a 3.0 mm (0.118 in.)



Hide 56114 3.INSTALL WINDSHIELD GLASS RETAINER

a.

Apply the glass primer to the glass where the 2 new windshield glass stoppers will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from 2 new windshield glass retainers. Install the 2 new windshield glass retainers to the windshield glass at the locations shown in the illustration.

B388307C01
0.479,1.344 0.479,0.698 0.479,0.698 0.688,0.698 false 1.625,1.333 1.625,0.698 1.625,0.698 1.406,0.698 false 0.302,1.292 0.302,2.26 0.302,2.26 0.5,2.26 false 5.406,1.333 5.406,0.708 5.406,0.708 5.656,0.708 false 6.583,1.344 6.583,0.719 6.583,0.719 6.365,0.719 false 5.219,1.292 5.219,2.281 5.219,2.281 5.479,2.281 false 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.24,0.625 1.552,0.781 0.313,0.156 10 false *b 0.719,0.625 1.031,0.781 0.313,0.156 10 false *b 0.552,2.219 0.865,2.417 0.313,0.198 10 false *b 0.594,1.979 0.75,2.177 0.156,0.198 10 false a 1.427,1.99 1.583,2.188 0.156,0.198 10 false a 1.885,1.333 2.042,1.531 0.156,0.198 10 false b 5.719,0.635 6.031,0.833 0.313,0.198 10 false *b 6.198,0.646 6.51,0.844 0.313,0.198 10 false *b 6.833,1.333 6.99,1.531 0.156,0.198 10 false b 6.375,1.969 6.531,2.167 0.156,0.198 10 false a 5.531,1.99 5.688,2.188 0.156,0.198 10 false a 5.531,2.219 5.844,2.417 0.313,0.198 10 false *b
*a Back Side *b Ceramic Notch


Standard:
Area Specified Condition
a 5.0 mm (0.197 in.)
b 15.9 mm (0.626 in.)



Hide 56115A 4.INSTALL NO. 1 WINDSHIELD GLASS STOPPER

a.

Apply the glass primer to the glass where the No. 1 windshield glass stopper will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.



b.
B388308C01
0.49,2 0.667,1.729 0.667,1.729 0.927,1.729 false 0.74,2.25 0.865,1.958 0.865,1.958 1.083,1.958 false 2.073,2.573 2.073,2.094 2.073,2.094 1.938,2.094 false 0.979,1.656 1.292,1.813 0.313,0.156 10 false *1 1.146,1.885 1.458,2.042 0.313,0.156 10 false *2 0.052,0.063 0.365,0.219 0.313,0.156 10 false *a 1.792,2.01 2.104,2.167 0.313,0.156 10 false *b 0.385,1.385 1.156,1.583 0.771,0.198 10 false A - A 1.125,2.531 1.281,2.729 0.156,0.198 10 false b 2.125,2.875 2.281,3.073 0.156,0.198 10 false a 2.833,2.875 2.99,3.073 0.156,0.198 10 false a 2.438,1.594 2.594,1.792 0.156,0.198 10 false A 2.448,2.938 2.604,3.135 0.156,0.198 10 false A
*1 Windshield Glass
*2 No. 1 Windshield Glass Stopper
*a Back Side
*b Ceramic Line


Remove the peeling paper from a new No. 1 windshield glass stopper. Install the No. 1 windshield glass stopper to the windshield glass at the location shown in the illustration.

Standard:
Area Specified Condition
a 5.0 mm (0.197 in.)
b 17.1 mm (0.673 in.)



Hide 56116C 5.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.

Apply the glass primer to the glass where the No. 2 windshield glass stopper will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.



b.
B388304C01
2.75,2.208 2.813,1.969 2.813,1.969 3.063,1.969 false 2.469,1.938 2.656,1.75 2.656,1.75 2.854,1.75 false 0.729,2.51 0.729,2.052 0.729,2.052 0.583,2.052 false 2.885,1.677 3.198,1.833 0.313,0.156 10 false *1 3.115,1.885 3.427,2.042 0.313,0.156 10 false *2 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a 0.427,1.979 0.74,2.135 0.313,0.156 10 false *b 1.125,1.51 1.281,1.708 0.156,0.198 10 false A 1.125,2.896 1.281,3.094 0.156,0.198 10 false A 2.417,1.396 3.188,1.594 0.771,0.198 10 false A - A 3.156,2.479 3.313,2.677 0.156,0.198 10 false b 0.76,2.833 0.917,3.031 0.156,0.198 10 false a 1.469,2.823 1.625,3.021 0.156,0.198 10 false a
*1 Windshield Glass
*2 No. 2 Windshield Glass Stopper
*a Back Side
*b Ceramic Line


Remove the peeling paper from a new No. 2 windshield glass stopper. Install the No. 2 windshield glass stopper. to the windshield glass at the location shown in the illustration.

Standard:
Area Specified Condition
a 5.0 mm (0.196 in.)
b 17.1 mm (0.673 in.)



Hide 56121 6.INSTALL WINDSHIELD WEATHERSTRIP

a.

Using a brush or sponge, coat the contact surface of the windshield glass and windshield weatherstrip with the glass primer as shown in the illustration.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Do not coat the adhesive with primer.

·

Throw away any leftover primer.




b.

Install the windshield weatherstrip to the windshield glass at the locations shown in the illustration.

B231543C02
0.885,1.51 2.354,2.677 1.469,1.167 4.688,1.052 4.646,0.698 4.646,0.698 4.563,0.698 false 4.917,1.927 5.052,1.927 5.052,1.927 5.052,1.458 true 1.479,0.292 1.604,0.458 0.125,0.167 10 false A 0.615,0.438 0.74,0.604 0.125,0.167 10 false B 2.74,0.406 2.865,0.573 0.125,0.167 10 false B 3.948,0.365 4.073,0.531 0.125,0.167 10 false B 2.854,1.24 2.979,1.406 0.125,0.167 10 false B 0.51,1.25 0.635,1.417 0.125,0.167 10 false B 1.479,0.51 1.604,0.677 0.125,0.167 10 false A 0.958,1.552 1.333,1.76 0.375,0.208 10 false A - A 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 4.396,0.625 4.708,0.781 0.313,0.156 10 false *b 4.76,1.833 5.073,1.99 0.313,0.156 10 false *c 1.292,2.49 1.604,2.646 0.313,0.156 10 false *a
*a Back Side *b Ceramic Line
*c Windshield weatherstrip of protruding part - -



Hide 56111 7.INSTALL WINDSHIELD GLASS

a.
B231524C04
0.854,1.052 1.042,1.052 false 1.083,1.01 1.396,1.167 0.313,0.156 10 false *a
*a Matchmark


Position the windshield glass.

i.

Using suction cups, place the glass in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Place matchmarks on the glass and vehicle body on the locations indicated in the illustration.

HINT:
·

Placing matchmarks is only necessary when installing new glass. When reinstalling the used glass, matchmarks should already be present.

·

When reusing the glass, check and correct the matchmark positions.



NOTICE:

Check that the stoppers are attached to the vehicle body correctly.



iv.

Using suction cups, remove the windshield glass.



b.
B106085C13
2.302,2.281 1.896,2.281 true 2.427,1.094 2.208,1.094 false 2.375,2.156 2.208,1.979 2.208,1.979 2,1.979 true 1.979,0.385 2.292,0.542 0.313,0.156 10 false *a 1.948,1.635 2.26,1.792 0.313,0.156 10 false *b 0.542,4.375 0.854,4.531 0.313,0.156 10 false *c 1.729,2.188 2.042,2.344 0.313,0.156 10 false *d 1.844,1.885 2.156,2.042 0.313,0.156 10 false *c 2.052,1 2.365,1.156 0.313,0.156 10 false *c
*a CORRECT
*b INCORRECT
*c Body Primer
*d Adhesive
V100155

Body Primer Application Area


Using a brush, apply the body primer to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.




c.

Using a brush or sponge, apply the glass primer to the contact surface of the windshield glass.

B231541C02
1.615,2.188 1.771,2.729 1.771,2.729 2.083,2.729 true 4.542,0.75 4.333,0.979 4.333,0.979 4.333,1.198 false 6.292,0.729 6.083,0.969 6.083,0.969 6.083,1.177 false 4.542,2.615 4.333,2.854 4.333,2.854 4.333,3.063 false 6,2.604 6.302,2.854 6.302,2.854 6.281,2.594 false 6.302,2.854 6.302,3.177 false 0.573,1.01 0.688,1.156 0.115,0.146 10 false B 2.469,1.042 2.583,1.188 0.115,0.146 10 false B 2.469,1.281 2.583,1.427 0.115,0.146 10 false B 0.573,1.281 0.688,1.427 0.115,0.146 10 false B 1.531,1.031 1.646,1.177 0.115,0.146 10 false A 1.531,1.271 1.646,1.417 0.115,0.146 10 false A 1.135,1.948 1.25,2.094 0.115,0.146 10 false C 1.135,2.219 1.25,2.365 0.115,0.146 10 false C 2.479,1.969 2.594,2.115 0.115,0.146 10 false D 2.49,2.219 2.604,2.365 0.115,0.146 10 false D 2.802,1.875 2.917,2.021 0.115,0.146 10 false A 3.063,1.844 3.177,1.99 0.115,0.146 10 false A 4,0.021 4.563,0.188 0.563,0.167 10 false A - A 5.667,0.021 6.229,0.177 0.563,0.156 10 false B - B 3.99,1.615 4.604,1.792 0.615,0.177 10 false C - C 5.667,1.615 6.021,1.771 0.354,0.156 10 false D - D 6.083,2.042 6.188,2.188 0.104,0.146 10 false b 6.656,2.313 6.76,2.458 0.104,0.146 10 false a 4.542,0.292 4.646,0.438 0.104,0.146 10 false a 6.292,0.313 6.396,0.458 0.104,0.146 10 false a 4.552,2.104 4.656,2.25 0.104,0.146 10 false a 5.896,2.958 6,3.104 0.104,0.146 10 false c 0.5,1.771 0.615,1.917 0.115,0.146 10 false A 0.74,1.792 0.854,1.938 0.115,0.146 10 false A 4.146,0.469 4.25,0.615 0.104,0.146 10 false c 0.167,0.042 0.479,0.198 0.313,0.156 10 false *a 4.271,1.198 4.583,1.354 0.313,0.156 10 false *b 0.542,3.469 0.854,3.625 0.313,0.156 10 false :*c 6.031,1.188 6.344,1.344 0.313,0.156 10 false *b 4.26,3.083 4.573,3.24 0.313,0.156 10 false *b 6.24,3.198 6.552,3.354 0.313,0.156 10 false *b 2.125,2.656 2.438,2.813 0.313,0.156 10 false *b
*a Back Side *b Adhesive Center Line
*c Glass Primer - -
V100155

Glass Primer Application Area - -


Standard:
Area Specified Condition
a 6.5 mm (0.2559 in.)
b 8.0 mm (0.3150 in.)
c 7.0 mm (0.2756 in.)


HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




d.

Apply adhesive to the windshield glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the windshield glass as shown in the illustration.

B231542C02
4.594,0.948 4.385,1.188 4.385,1.188 4.385,1.396 false 6.26,0.938 6.052,1.177 6.052,1.177 6.052,1.385 false 4.76,2.76 4.552,2.99 4.552,2.99 4.552,3.281 false 6.052,2.729 6.167,3.24 6.167,3.24 6.25,2.729 false 2.49,2.51 2.49,2.938 false 1.302,1.323 1.417,1.469 0.115,0.146 10 false B 3.188,1.323 3.302,1.469 0.115,0.146 10 false B 3.188,1.604 3.302,1.75 0.115,0.146 10 false B 1.302,1.583 1.417,1.729 0.115,0.146 10 false B 2.25,1.313 2.365,1.458 0.115,0.146 10 false A 2.25,1.583 2.365,1.729 0.115,0.146 10 false A 3.208,2.25 3.323,2.396 0.115,0.146 10 false D 3.208,2.542 3.323,2.688 0.115,0.146 10 false D 1.854,2.26 1.969,2.406 0.115,0.146 10 false C 1.854,2.531 1.969,2.677 0.115,0.146 10 false C 3.542,2.188 3.656,2.333 0.115,0.146 10 false A 3.781,2.146 3.896,2.292 0.115,0.146 10 false A 4.052,0.063 4.583,0.219 0.531,0.156 10 false A - A 5.719,0.063 6.354,0.219 0.635,0.156 10 false B - B 4.042,1.76 4.781,1.99 0.74,0.229 10 false C - C 5.719,1.76 6.073,1.917 0.354,0.156 10 false D - D 6.094,2.156 6.198,2.302 0.104,0.146 10 false b 0.635,2.885 0.74,3.031 0.104,0.146 10 false b 0.833,1.719 0.938,1.865 0.104,0.146 10 false b 0.281,3.292 0.385,3.438 0.104,0.146 10 false a 0.344,1.5 0.448,1.646 0.104,0.146 10 false a 4.771,2.146 4.875,2.292 0.104,0.146 10 false c 4.594,0.354 4.698,0.5 0.104,0.146 10 false c 6.25,0.344 6.354,0.49 0.104,0.146 10 false c 1.229,2.073 1.344,2.219 0.115,0.146 10 false A 1.458,2.104 1.573,2.25 0.115,0.146 10 false A 0.052,0.031 0.365,0.188 0.313,0.156 10 false *a 4.323,1.417 4.635,1.573 0.313,0.156 10 false *b 6.01,1.417 6.323,1.573 0.313,0.156 10 false *b 6.115,3.25 6.427,3.406 0.313,0.156 10 false *b 4.479,3.302 4.792,3.458 0.313,0.156 10 false *b 2.417,2.927 2.729,3.083 0.313,0.156 10 false *b
*a Back Side *b Adhesive Center Line


Standard:
Area Specified Condition
a 12.0 mm (0.4724 in.)
b 8.0 mm (0.3150 in.)
c 6.5 mm (0.2559 in.)




e.
B231525C02
0.865,1.052 1.177,1.052 false 1.198,0.979 1.51,1.135 0.313,0.156 10 false *a
*a Matchmarks


Install the glass to the vehicle body.

i.

Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.


ii.

Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.

NOTICE:
·

Check that the stoppers are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.




iii.

Using a scraper, remove any excess or protruding adhesive.

HINT:

Apply adhesive to any areas where the amount of adhesive is inadequate.



iv.

Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.

NOTICE:

Do not drive the vehicle for the amount of time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




Hide 56111 8.CHECK FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 63310 9.INSTALL ROOF HEADLINING ASSEMBLY

a.

for Model Code #J71 Series:

Return the roof headlining to its original position. Refer to the following procedures.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Short Body)>INSTALLATION


b.

for Model Code #J76 Series:

Return the roof headlining to its original position. Refer to the following procedures.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Semi-long Body)>INSTALLATION


c.

for Model Code #J78 Series:

Return the roof headlining to its original position. Refer to the following procedures.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Long Body)>INSTALLATION


d.

for Model Code #J79 Series:

Return the roof headlining to its original position. Refer to the following procedures.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Double Cab)>INSTALLATION


Hide 86401 10.INSTALL FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY (w/ Front Camera)

Hide 8646C 11.INSTALL FORWARD RECOGNITION CAMERA (w/ Front Camera)

Hide 86464A 12.INSTALL FORWARD RECOGNITION LATCH (w/ Front Camera)

Hide 86466D 13.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Front Camera)

Hide 62316C 20.INSTALL FRONT DOOR REAR OPENING TRIM WEATHERSTRIP LH

Hide 62315E 21.INSTALL FRONT DOOR REAR OPENING TRIM WEATHERSTRIP RH

Hide 62111A 22.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 62111A 23.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

Hide 26.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH

Hide 27.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH

Hide 8646C 28.ADJUST FORWARD RECOGNITION CAMERA (w/ Front Camera)

a.

If the forward recognition camera has been replaced with a new one or the windshield glass has been removed and installed, it is necessary to perform Forward Recognition Camera Learning.

HINT:

Forward Recognition Camera Learning can be performed by using either Target Adjustment (One Time Recognition) or Target Adjustment (Sequential Recognition) or Driving Adjustment.