Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C050C14  Left Rear Wheel Speed Sensor Circuit Short to Ground or Open  C051214  Right Rear Wheel Speed Sensor Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTCs C050C1F and C05121F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>C050C1F

DTC No. Detection Item DTC Detection Condition Trouble Area
C050C14 Left Rear Wheel Speed Sensor Circuit Short to Ground or Open An open in the speed sensor signal circuit continues for 0.5 seconds or more.
·

Rear speed sensor LH

·

Wire harness or connector

·

Skid control sensor wire

·

Skid control ECU (Brake actuator assembly)


C051214 Right Rear Wheel Speed Sensor Circuit Short to Ground or Open An open in the speed sensor signal circuit continues for 0.5 seconds or more.
·

Rear speed sensor RH

·

Wire harness or connector

·

Skid control sensor wire

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
RL Speed Open Rear speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
Chassis > Brake > Data List
Tester Display
RR Speed Open
RL Speed Open
RR Speed Sensor Voltage Open
RL Speed Sensor Voltage Open
50003 435 103,104,112,113
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

4.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

According to the display on the GTS, read the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 435 15,16

b.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)
3.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test


e.

Check if the same DTC is recorded.

Chassis > Brake > Trouble Codes
50001 435

Result:
Proceed to
DTCs C050C14 and C051214 are not output
DTCs C050C14 and/or C051214 are output



DTCs C050C14 and C051214 are not output

DTCs C050C14 and/or C051214 are output

4.INSPECT SKID CONTROL SENSOR WIRE
C269768C06
1.198,0.813 1.365,1 0.167,0.188 3.427,0.542 3.729,0.74 0.302,0.198 5.844,0.833 6.021,1.01 0.177,0.177 3.792,1.344 4.167,0.833 4.167,0.833 4.25,0.833 true 3.458,1.344 3.167,0.833 3.167,0.833 3.083,0.833 true 3.427,1.573 2.917,1.917 2.917,1.917 2.917,2.083 true 3.792,1.583 4.25,1.917 4.25,1.917 4.25,2.083 true 6.094,0.708 6.406,0.865 0.313,0.156 10 false *A 1.417,0.688 1.729,0.844 0.313,0.156 10 false *B 0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 1.208,2.229 1.521,2.385 0.313,0.156 10 false *a 3.563,2.146 3.875,2.302 0.313,0.156 10 false *b 1.24,0.833 1.396,1.031 0.156,0.198 10 false D 3.5,0.563 3.823,0.75 0.323,0.188 10 false V3 5.885,0.844 6.042,1.042 0.156,0.198 10 false C 5.896,2.292 6.104,2.479 0.208,0.188 10 false *a 4.281,0.76 4.594,0.948 0.313,0.188 10 false RL- 2.781,0.75 3.083,0.917 0.302,0.167 10 false RL+ 2.823,2.094 3.125,2.271 0.302,0.177 10 false RR+ 4.167,2.125 4.469,2.313 0.302,0.188 10 false RR-
*A for RH *B for LH
*1 Skid Control Sensor Wire - -
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the C or D skid control sensor wire connector (speed sensor side).


d.

Disconnect the V3 skid control sensor wire connector (wire harness side).


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
V3-3 (RR+) - C-3 Always Below 1 Ω
V3-4 (RR-) - C-1 Always Below 1 Ω
V3-3 (RR+) or C-3 - Body ground Always 10 kΩ or higher
V3-4 (RR-) or C-1 - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
V3-1 (RL+) - D-3 Always Below 1 Ω
V3-2 (RL-) - D-1 Always Below 1 Ω
V3-1 (RL+) or D-3 - Body ground Always 10 kΩ or higher
V3-2 (RL-) or D-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)

NG

REPLACE SKID CONTROL SENSOR WIRE

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A45 skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A45-20 (RR+) - V3-3 (RR+) Always Below 1 Ω
A45-19 (RR-) - V3-4 (RR-) Always Below 1 Ω
A45-20 (RR+) or V3-3 (RR+) - Body ground Always 10 kΩ or higher
A45-19 (RR-) or V3-4 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A45-5 (RL+) - V3-1 (RL+) Always Below 1 Ω
A45-4 (RL-) - V3-2 (RL-) Always Below 1 Ω
A45-5 (RL+) or V3-1 (RL+) - Body ground Always 10 kΩ or higher
A45-4 (RL-) or V3-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.

Reconnect the A45 skid control ECU (brake actuator assembly) connector.


b.

Reconnect the V3 skid control sensor wire connector.


c.

Turn the ignition switch to ON.


d.
C269769C06
1.604,0.135 1.833,0.333 0.229,0.198 1.604,0.406 1.833,0.594 0.229,0.188 1.885,0.083 2.198,0.24 0.313,0.156 10 false *A 1.885,0.375 2.198,0.531 0.313,0.156 10 false *B 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 1.667,0.146 1.823,0.344 0.156,0.198 10 false C 1.667,0.417 1.823,0.615 0.156,0.198 10 false D
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
C-3 - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
D-3 - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

NG