Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C051D54  Multi-axis Acceleration Sensor Module "A" Missing Calibration  C121054  Yaw Rate Sensor Missing Calibration  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via the CAN communication system.

The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition. If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag ECU assembly) and the CAN communication system, the DTC U012587 is output.

The DTCs are also output when the calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area
C051D54 Multi-axis Acceleration Sensor Module "A" Missing Calibration Zero point calibration of acceleration sensor undone.
·

Acceleration sensor zero point calibration incomplete

·

Sensor installation

·

Acceleration sensor (Airbag ECU assembly)

·

Skid control ECU (Brake actuator assembly)


C121054 Yaw Rate Sensor Missing Calibration Zero point calibration of yaw rate sensor undone. Yaw rate sensor zero point calibration incomplete

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION

·

If the yaw rate and acceleration sensor (airbag ECU assembly) was replaced or reinstalled, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION



HINT:

When U012587 and/or U012687 is output along with C051D54 and/or C121054, inspect and repair trouble areas indicated by U012587 and/or U012687 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>U007488


PROCEDURE

1.PERFORM CALIBRATION

NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


c.

Check for DTCs.

Chassis > Brake > Trouble Codes
50001 435
Result:
Result Proceed to
DTCs C051D54 and C121054 are not output. A
DTCs C051D54 and/or C121054 are output. B




A

END

B

3.CHECK AIRBAG ECU ASSEMBLY INSTALLATION
3.CHECK AIRBAG ECU ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the airbag ECU assembly has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The sensor should be tightened to the specified torque.

The sensor is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)

NG

4.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
a.

Check the yaw rate and acceleration sensor output value displayed on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Chassis > Brake > Data List
Tester Display
Lateral G
Forward and Rearward G
Yaw Rate Sensor Value
50003 435 25,26,29
OK:

The yaw rate and acceleration sensor (airbag ECU assembly) output value is normal.



Result:
Proceed to
OK
NG



OK

NG