Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU assembly is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation.

When the VSC OFF switch is pressed and held for 3 seconds or more with the vehicle stopped, the system enters VSC OFF mode and TRC and VSC operation stop. Also, the TRC OFF indicator and the VSC OFF indicator lights come on.

When the transfer is shifted to L4, VSC is prohibited and the VSC OFF indicator light turns on.

w/ Rear Differential Lock:

When the rear differential is locked, VSC is prohibited, and the VSC OFF and TRC OFF indicator lights turn on.

WIRING DIAGRAM

C427345E43
0.917,0.896 1.375,1.104 0.458,0.208 10 false CANL 0.906,1.729 1.344,1.927 0.438,0.198 10 false CANH 1.396,0.74 1.708,0.938 0.313,0.198 10 false 14 1.406,1.552 1.719,1.75 0.313,0.198 10 false 13 5.073,0.74 5.385,0.938 0.313,0.198 10 false 43 5.073,1.552 5.385,1.75 0.313,0.198 10 false 27 5.354,0.896 5.792,1.104 0.438,0.208 10 false CANL 5.354,1.719 5.833,1.906 0.479,0.188 10 false CANH 3.469,2.75 3.625,2.948 0.156,0.198 10 false 4 4.542,2.75 4.698,2.948 0.156,0.198 10 false 3 0.146,3.823 0.479,4.01 0.333,0.188 10 false L26 3.521,3.24 3.844,3.438 0.323,0.198 10 false L49 3.542,3.427 5.188,3.781 1.646,0.354 10 false VSC OFF Switch 5.156,2.74 5.469,2.938 0.313,0.198 10 false 9 5.365,2.99 5.823,3.188 0.458,0.198 10 false CSW 5.104,3.906 5.563,4.104 0.458,0.198 10 false A45 5.094,4.083 6.99,4.49 1.896,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 2.896,4.323 4.615,4.531 1.719,0.208 10 false : CAN Communication Line 0.135,3.979 2,4.188 1.865,0.208 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION

·

As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first.

Click hereDrivetrain>HF1A (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>PROBLEM SYMPTOMS TABLE



PROCEDURE

1.CHECK FOR DIFFERENTIAL SYSTEM

Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

2.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / Not defined / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
Not defined: Not defined
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
Chassis > Brake > Data List
Tester Display
TRC(TRAC)/VSC OFF Mode
50003 435 45

b.

Check that the indicator light and mode condition on the GTS change according to VSC OFF switch operation.

Standard:
Switch Operation Mode Condition Display TRC OFF Indicator Light VSC OFF Indicator Light
Not pressed Normal mode (TRC(TRAC) ON/VSC ON) Does not come on Does not come on
Pressing the VSC OFF switch TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) Does not come on Comes on
Pressing and holding the VSC OFF switch VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Comes on Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

3.INSPECT VSC OFF SWITCH

B

C

3.INSPECT VSC OFF SWITCH
a.

Inspect the VSC OFF switch.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH (w/ VSC)>INSPECTION

OK:

The VSC OFF switch operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Disconnect the A45 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-9 (CSW) - L49-3 Always Below 1 Ω
A45-9 (CSW) or L49-3 - Body ground Always 10 kΩ or higher
L49-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR