Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2021.12
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  P0018  Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the intake camshaft and camshaft timing oil control valve assembly, and operating the camshaft timing gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) Deviations in the crankshaft position sensor signal and VVT sensor (for bank 1) signal (2 trip detection logic).
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

Camshaft timing oil control valve assembly (for bank 1)

·

Oil control valve filter

·

Camshaft timing gear assembly (for bank 1)

·

ECM


Comes on / - DTC stored
P0018 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A) Deviations in the crankshaft position sensor signal and VVT sensor (for bank 2) signal (2 trip detection logic).
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

Camshaft timing oil control valve assembly (for bank 2)

·

Oil control valve filter

·

Camshaft timing gear assembly (for bank 2)

·

ECM


Comes on / - DTC stored

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0016 (Bank 1) or P0018 (Bank 2).

CONFIRMATION DRIVING PATTERN

A197314E80
4.271,1.115 4.604,0.448 4.604,0.448 4.75,0.448 false 0.156,0.656 1.083,0.802 0.927,0.146 10 false Vehicle Speed 1.542,2.156 1.75,2.354 0.208,0.198 10 false [A] 2.167,1.656 2.396,1.823 0.229,0.167 10 false [B] 3.188,1.646 3.396,1.802 0.208,0.156 10 false [C] 3.823,3.01 4.031,3.167 0.208,0.156 10 false [D] 4.625,0.865 4.823,1.063 0.198,0.198 10 false [E] 5.656,1.615 5.854,1.813 0.198,0.198 10 false [F] 6.375,3.021 6.615,3.208 0.24,0.188 10 false [G] 0.667,1.792 1.052,1.979 0.385,0.188 10 false Idling 4.813,0.365 6.292,0.729 1.479,0.365 10 false There is no designated vehicle speed 0.083,2.083 1.01,2.396 0.927,0.313 10 false Ignition Switch ON 1.917,2.573 2.708,2.906 0.792,0.333 10 false Warming up the engine 2.74,2.583 3.896,2.75 1.156,0.167 10 false 5 minutes or more 5.271,2.604 6.427,2.771 1.156,0.167 10 false 5 minutes or more 4.125,2.604 5.021,2.771 0.896,0.167 10 false 2 to 3 minutes

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Idle the engine for 5 minutes or more [C].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0016 or P0018.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].



13.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Idle the engine for 5 minutes or more [F].

15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [G].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0018)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
DTC P0016 or P0018 is output A
DTC P0016 or P0018 and other DTCs are output B


HINT:

If any DTCs other than P0016 or P0018 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) / Ptrl Valve Control / VVT Change Angle #1 or VVT Change Angle #2.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the VVT Linear (Bank1)
50004 61 32
Powertrain > Engine and ECT > Active Test
Tester Display
Control the VVT Linear (Bank2)
50004 61 31

e.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE MECHANICAL SYSTEM

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.CHECK ENGINE MECHANICAL SYSTEM
a.

Check the engine mechanical system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0018)
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

5.INSPECT OIL CONTROL VALVE FILTER
a.

Remove the oil control valve filter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly (for bank1 or bank2).

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0018)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0018)
a.

In order to clear the ECM learned values for valve timing,disconnect the cable from the negative (-) batteryterminal for 1 minute.


b.

Connect the cable to the negative (-) battery terminal.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

Powertrain > Engine and ECT > Trouble Codes
50001 61

i.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0016 or P0018 is output B




A

END

B