The injector driver (EDU) delivers drive signals to fuel injectors using the DC/DC converter, which provides a high-voltage and quick-charging system.
Soon after the injector driver (EDU) receives a fuel injection command (#1 to #8) signal from the ECM, the injector driver (EDU) responds to the command with an injector injection confirmation (INJF, INF2) signal when the current is applied to the fuel injector.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0201 | Injector Circuit / Open - (Cylinder 1) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). |
·
Open or short in fuel injector circuit
·
Fuel injector
·
No. 1 injector driver (EDU)
·
No. 2 injector driver (EDU)
·
ECM |
Comes on | DTC stored |
| P0202 | Injector Circuit / Open - (Cylinder 2) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). |
·
Open or short in fuel injector circuit
·
Fuel injector
·
No. 1 injector driver (EDU)
·
No. 2 injector driver (EDU)
·
ECM |
Comes on | DTC stored |
| P0203 | Injector Circuit / Open - (Cylinder 3) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). |
·
Open or short in fuel injector circuit
·
Fuel injector
·
No. 1 injector driver (EDU)
·
No. 2 injector driver (EDU)
·
ECM |
Comes on | DTC stored |
| P0204 | Injector Circuit / Open - (Cylinder 4) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). |
·
Open or short in fuel injector circuit
·
Fuel injector
·
No. 1 injector driver (EDU)
·
No. 2 injector driver (EDU)
·
ECM |
Comes on | DTC stored |
| P0205 | Injector Circuit / Open - (Cylinder 5) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). |
·
Open or short in fuel injector circuit
·
Fuel injector
·
No. 1 injector driver (EDU)
·
No. 2 injector driver (EDU)
·
ECM |
Comes on | DTC stored |
| P0206 | Injector Circuit / Open - (Cylinder 6) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). |
·
Open or short in fuel injector circuit
·
Fuel injector
·
No. 1 injector driver (EDU)
·
No. 2 injector driver (EDU)
·
ECM |
Comes on | DTC stored |
| P0207 | Injector Circuit / Open - (Cylinder 7) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). |
·
Open or short in fuel injector circuit
·
Fuel injector
·
No. 1 injector driver (EDU)
·
No. 2 injector driver (EDU)
·
ECM |
Comes on | DTC stored |
| P0208 | Injector Circuit / Open - (Cylinder 8) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). |
·
Open or short in fuel injector circuit
·
Fuel injector
·
No. 1 injector driver (EDU)
·
No. 2 injector driver (EDU)
·
ECM |
Comes on | DTC stored |
| P062D | No. 1 Fuel Injector Driver Circuit Performance | Inconsistency in the injection waveforms between the injector driver (EDU) and ECM while the engine is running a certain number of times (a maximum of approx. 0.5 seconds). |
·
Open or short in injector driver (EDU) circuit
·
Fuel injector
·
No. 1 injector driver (EDU)
·
No. 2 injector driver (EDU)
·
ECM |
Comes on | DTC stored |
| P062E | No. 2 Fuel Injector Driver Circuit Performance | Inconsistency in the injection waveforms between the injector driver (EDU) and ECM while the engine is running a certain number of times (a maximum of approx. 0.5 seconds). |
·
Open or short in injector driver (EDU) circuit
·
Fuel injector
·
No. 1 injector driver (EDU)
·
No. 2 injector driver (EDU)
·
ECM |
Comes on | DTC stored |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0201 P0202 P0203 P0204 P0205 P0206 P0207 P0208 P062D P062E |
Idling for 5 seconds |
The ECM compares injection command (#1 to #8) signals and injection confirmation (INJF, INF2) signals for each cylinder. If the ECM determines that a cylinder has a malfunction, DTC P0201, P0202, P0203, P0204, P0205, P0206, P0207 or P0208 will be stored.
The ECM continuously monitors both injection command (#1 to #8) signals and injection confirmation (INJF, INF2) signals. These DTCs will be stored if the ECM determines that the number of #1 to #8 signals and INJF, INF2 signals are inconsistent.
The injector assemblies are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the injector driver (EDU) (injector drive circuit) in relation to the current drawn by the fuel injector. When the fuel injector current becomes too high, the voltage drops over the resistor exceeds a specified level and no INJF or INF2 signal for that cylinder is sent to the ECM.
After the engine is started, when there is no injection confirmation (INJF, INF2) signal from the injector driver (EDU) to the ECM even though the ECM sends injection command (#1 to #8) signals to the injector driver (EDU), DTC P062D or P062E is stored.
If either of these DTCs is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The fail-safe mode continues until the ignition switch is turned off.
Make sure to perform work on high voltage circuits with the ignition switch off.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an fuel injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
Check the engine cranking condition.
| Result | Proceed to |
|---|---|
| Engine starts, but idling is rough (P062D or P062E is output)*1 | A |
| Engine starts, but idling is rough*2 | B |
| Engine does not start (P062D and P062E are output)*3 | C |
| Except above | D |
*1: Only one of either DTC P062D or P062E is output and one of the injector drivers (EDU) has stopped.
*2: DTC P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P062D and P062E are stored at this time.
*3: When the engine cannot be started due to a malfunction in the No. 1 and No. 2 injector driver (EDU), DTCs are not stored again if they are cleared.
Also, the value for "Common Rail Pressure" is higher than the value for "Target Common Rail Pressure"
A
B
C
D
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>CHECK FOR INTERMITTENT PROBLEMS
| *A | Bank 1 |
| *B | Bank 2 |
| *a | Front view of wire harness connector (to Injector Driver) |
Disconnect the No. 1 and No. 2 injector driver (EDU) connectors.
Check the waveform of the No. 1 or No. 2 injector driver (EDU) connector using an oscilloscope.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C122-5 (#10) - Body ground | Cranking | Correct waveform is as shown |
| C125-5 (#20) - Body ground | Cranking | Correct waveform is as shown |
| C125-3 (#30) - Body ground | Cranking | Correct waveform is as shown |
| C122-6 (#40) - Body ground | Cranking | Correct waveform is as shown |
| C125-6 (#50) - Body ground | Cranking | Correct waveform is as shown |
| C122-2 (#60) - Body ground | Cranking | Correct waveform is as shown |
| C122-3 (#70) - Body ground | Cranking | Correct waveform is as shown |
| C125-2 (#80) - Body ground | Cranking | Correct waveform is as shown |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Powering of the EDU relay may be prohibited by the fail-safe function. Therefore, turn the ignition switch off to disable the fail-safe function before performing this inspection.
| *A | for Bank 1 (No. 1 Injector Driver (EDU)) |
| *B | for Bank 2 (No. 2 Injector Driver (EDU)) |
| *a | Front view of wire harness connector (to Injector Driver (EDU)) |
Disconnect the No. 1 or No. 2 injector driver (EDU) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C124-3 (+B) - C124-1 (GND) | Ignition switch ON | 11 to 14 V |
| C127-3 (+B) - C127-1 (GND) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 or No. 2 injector driver (EDU) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C122-5 (#10) - C39-40 (#1) | Always | Below 1 Ω |
| C125-5 (#20) - C39-39 (#2) | Always | Below 1 Ω |
| C125-3 (#30) - C39-38 (#3) | Always | Below 1 Ω |
| C122-6 (#40) - C39-37 (#4) | Always | Below 1 Ω |
| C125-6 (#50) - C39-36 (#5) | Always | Below 1 Ω |
| C122-2 (#60) - C39-35 (#6) | Always | Below 1 Ω |
| C122-3 (#70) - C39-34 (#7) | Always | Below 1 Ω |
| C125-2 (#80) - C39-33 (#8) | Always | Below 1 Ω |
| C122-5 (#10) or C39-40 (#1) - Body ground | Always | 10 kΩ or higher |
| C125-5 (#20) or C39-39 (#2) - Body ground | Always | 10 kΩ or higher |
| C125-3 (#30) or C39-38 (#3) - Body ground | Always | 10 kΩ or higher |
| C122-6 (#40) or C39-37 (#4) - Body ground | Always | 10 kΩ or higher |
| C125-6 (#50) or C39-36 (#5) - Body ground | Always | 10 kΩ or higher |
| C122-2 (#60) or C39-35 (#6) - Body ground | Always | 10 kΩ or higher |
| C122-3 (#70) or C39-34 (#7) - Body ground | Always | 10 kΩ or higher |
| C125-2 (#80) or C39-33 (#8) - Body ground | Always | 10 kΩ or higher |
Reconnect the No. 1 or No. 2 injector driver (EDU) connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 or No. 2 injector driver (EDU).
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine and idle it for 5 seconds or more.
Turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 1 or No. 2 injector driver (EDU) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C122-5 (#10) - C39-40 (#1) | Always | Below 1 Ω |
| C125-5 (#20) - C39-39 (#2) | Always | Below 1 Ω |
| C125-3 (#30) - C39-38 (#3) | Always | Below 1 Ω |
| C122-6 (#40) - C39-37 (#4) | Always | Below 1 Ω |
| C125-6 (#50) - C39-36 (#5) | Always | Below 1 Ω |
| C122-2 (#60) - C39-35 (#6) | Always | Below 1 Ω |
| C122-3 (#70) - C39-34 (#7) | Always | Below 1 Ω |
| C125-2 (#80) - C39-33 (#8) | Always | Below 1 Ω |
| C122-5 (#10) or C39-40 (#1) - Body ground | Always | 10 kΩ or higher |
| C125-5 (#20) or C39-39 (#2) - Body ground | Always | 10 kΩ or higher |
| C125-3 (#30) or C39-38 (#3) - Body ground | Always | 10 kΩ or higher |
| C122-6 (#40) or C39-37 (#4) - Body ground | Always | 10 kΩ or higher |
| C125-6 (#50) or C39-36 (#5) - Body ground | Always | 10 kΩ or higher |
| C122-2 (#60) or C39-35 (#6) - Body ground | Always | 10 kΩ or higher |
| C122-3 (#70) or C39-34 (#7) - Body ground | Always | 10 kΩ or higher |
| C125-2 (#80) or C39-33 (#8) - Body ground | Always | 10 kΩ or higher |
Reconnect the injector driver (EDU) connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Go to injector circuit.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>Injector Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds.
Start the engine and idle it for 30 seconds.
Enter the following menus: Engine and ECT / Trouble Codes.
Check the DTCs output on the GTS.
The cylinder with the malfunctioning fuel injector can be determined based on the output DTCs.
If DTC P0201 is output, check the No. 1 fuel injector circuit.
If DTC P0202 is output, check the No. 2 fuel injector circuit.
If DTC P0203 is output, check the No. 3 fuel injector circuit.
If DTC P0204 is output, check the No. 4 fuel injector circuit.
If DTC P0205 is output, check the No. 5 fuel injector circuit.
If DTC P0206 is output, check the No. 6 fuel injector circuit.
If DTC P0207 is output, check the No. 7 fuel injector circuit.
If DTC P0208 is output, check the No. 8 fuel injector circuit.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector (to Fuel injector) |
Disconnect the fuel injector connectors for all cylinders.
If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all fuel injector connectors before inspecting the waveform.
Check the waveform of the fuel injector connectors using an oscilloscope.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C107-1 - C107-2 | Cranking | Voltage increases by 50 V or more |
| C115-1 - C115-2 | Cranking | Voltage increases by 50 V or more |
| C108-1 - C108-2 | Cranking | Voltage increases by 50 V or more |
| C117-1 - C117-2 | Cranking | Voltage increases by 50 V or more |
| C109-1 - C109-2 | Cranking | Voltage increases by 50 V or more |
| C113-1 - C113-2 | Cranking | Voltage increases by 50 V or more |
| C110-1 - C110-2 | Cranking | Voltage increases by 50 V or more |
| C112-1 - C112-2 | Cranking | Voltage increases by 50 V or more |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the fuel injector of the cylinder relevant to the DTC.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL
When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION
Perform PM forced regeneration.
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
| Proceed to |
|---|
| NEXT |
NEXT
Register the injector compensation code.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION
Perform the injector pilot quantity learning.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the fuel injector connectors.
Disconnect the No. 1 or No. 2 injector driver (EDU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C107-1 - C123-6 (IJ1+) | Always | Below 1 Ω |
| C107-2 - C123-3 (IJ1-) | Always | Below 1 Ω |
| C115-1 - C126-6 (IJ2+) | Always | Below 1 Ω |
| C115-2 - C126-3 (IJ2-) | Always | Below 1 Ω |
| C108-1 - C127-4 (IJ3+) | Always | Below 1 Ω |
| C108-2 - C127-2 (IJ3-) | Always | Below 1 Ω |
| C117-1 - C123-5 (IJ3+) | Always | Below 1 Ω |
| C117-2 - C123-2 (IJ3-) | Always | Below 1 Ω |
| C109-1 - C126-5 (IJ5+) | Always | 10 kΩ or higher |
| C109-2 - C126-2 (IJ5-) | Always | 10 kΩ or higher |
| C113-1 - C123-4 (IJ6+) | Always | 10 kΩ or higher |
| C113-2 - C123-1 (IJ6-) | Always | 10 kΩ or higher |
| C110-1 - C124-4 (IJ7+) | Always | 10 kΩ or higher |
| C110-2 - C124-2 (IJ7-) | Always | 10 kΩ or higher |
| C112-1 - C126-4 (IJ8+) | Always | 10 kΩ or higher |
| C112-2 - C126-1 (IJ8-) | Always | 10 kΩ or higher |
| C107-1 or C123-6 (IJ1+) - Body ground | Always | 10 kΩ or higher |
| C107-2 or C123-3 (IJ1-) - Body ground | Always | 10 kΩ or higher |
| C115-1 or C126-6 (IJ2+) - Body ground | Always | 10 kΩ or higher |
| C115-2 or C126-3 (IJ2-) - Body ground | Always | 10 kΩ or higher |
| C108-1 or C127-4 (IJ3+) - Body ground | Always | 10 kΩ or higher |
| C108-2 or C127-2 (IJ3-) - Body ground | Always | 10 kΩ or higher |
| C117-1 or C123-5 (IJ3+) - Body ground | Always | 10 kΩ or higher |
| C117-2 or C123-2 (IJ3-) - Body ground | Always | 10 kΩ or higher |
| C109-1 or C126-5 (IJ5+) - Body ground | Always | 10 kΩ or higher |
| C109-2 or C126-2 (IJ5-) - Body ground | Always | 10 kΩ or higher |
| C113-1 or C123-4 (IJ6+) - Body ground | Always | 10 kΩ or higher |
| C113-2 or C123-1 (IJ6-) - Body ground | Always | 10 kΩ or higher |
| C110-1 or C124-4 (IJ7+) - Body ground | Always | 10 kΩ or higher |
| C110-2 or C124-2 (IJ7-) - Body ground | Always | 10 kΩ or higher |
| C112-1 or C126-4 (IJ8+) - Body ground | Always | 10 kΩ or higher |
| C112-2 or C126-1 (IJ8-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| NEXT |
NEXT