Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2022.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  Starter Signal Circuit  


DESCRIPTION

When the engine is being cranked, the intake air flow is slow, so fuel vaporization is poor. A rich mixture is therefore necessary in order to achieve good startability. While the engine is being cranked, the battery positive voltage is applied to terminal STA of the ECM. The starter signal is mainly used to increase the fuel injection volume for starting injection control and after-start injection control.

WIRING DIAGRAM

for RHD
A225228E04
1.417,5.76 1.896,5.948 0.479,0.188 10 false Battery 2.677,5.646 3.146,5.813 0.469,0.167 10 false Starter 1.333,4.594 2.156,4.75 0.823,0.156 10 false FL MAIN 2.448,5.396 2.792,5.552 0.344,0.156 10 false D7 1.885,1.427 2.042,1.594 0.156,0.167 10 false 4 2.073,1.427 2.406,1.594 0.333,0.167 10 false AM1 2.031,1.792 2.365,1.958 0.333,0.167 10 false L21 2.031,1.938 2.979,2.125 0.948,0.188 10 false Ignition Switch 2.698,1.427 3.031,1.594 0.333,0.167 10 false ST1 3.083,1.427 3.24,1.594 0.156,0.167 10 false 3 3.042,3.781 3.198,3.948 0.156,0.167 10 false 5 3.604,3.781 3.76,3.948 0.156,0.167 10 false 1 3.042,4.594 3.198,4.76 0.156,0.167 10 false 3 3.583,4.594 3.74,4.76 0.156,0.167 10 false 2 3.802,2.625 4.031,2.813 0.229,0.188 10 false ST 3.979,4.146 4.25,4.302 0.271,0.156 10 false ST 5.021,3.26 5.25,3.427 0.229,0.167 10 false 48 5.677,5.635 5.969,5.802 0.292,0.167 10 false A29 5.677,5.813 6.042,5.979 0.365,0.167 10 false ECM 5.302,3.375 5.719,3.542 0.417,0.167 10 false STA 1.292,2.833 1.667,2.99 0.375,0.156 10 false ALT 1.313,2.094 1.729,2.25 0.417,0.156 10 false AM1 2.031,3.49 2.427,3.646 0.396,0.156 10 false AM2 3.073,5.146 3.344,5.302 0.271,0.156 10 false D6 2.5,5.177 2.656,5.344 0.156,0.167 10 false 1 3.375,5.146 3.531,5.313 0.156,0.167 10 false 1 3.573,2.385 3.729,2.552 0.156,0.167 10 false 1 3.583,2.844 3.74,3.01 0.156,0.167 10 false 2

for LHD
A225228E10
1.417,5.76 1.896,5.948 0.479,0.188 10 false Battery 2.677,5.646 3.146,5.813 0.469,0.167 10 false Starter 1.333,4.594 2.156,4.75 0.823,0.156 10 false FL MAIN 2.448,5.396 2.792,5.552 0.344,0.156 10 false D7 1.885,1.427 2.042,1.594 0.156,0.167 10 false 4 2.073,1.427 2.406,1.594 0.333,0.167 10 false AM1 2.031,1.792 2.365,1.958 0.333,0.167 10 false L21 2.031,1.938 2.979,2.125 0.948,0.188 10 false Ignition Switch 2.698,1.427 3.031,1.594 0.333,0.167 10 false ST1 3.083,1.427 3.24,1.594 0.156,0.167 10 false 3 3.042,3.781 3.198,3.948 0.156,0.167 10 false 5 3.604,3.781 3.76,3.948 0.156,0.167 10 false 1 3.042,4.594 3.198,4.76 0.156,0.167 10 false 3 3.583,4.594 3.74,4.76 0.156,0.167 10 false 2 3.802,2.625 4.031,2.813 0.229,0.188 10 false ST 3.979,4.146 4.25,4.302 0.271,0.156 10 false ST 5.021,3.26 5.25,3.427 0.229,0.167 10 false 48 5.677,5.635 5.969,5.802 0.292,0.167 10 false I84 5.677,5.813 6.042,5.979 0.365,0.167 10 false ECM 5.302,3.375 5.719,3.542 0.417,0.167 10 false STA 1.292,2.833 1.667,2.99 0.375,0.156 10 false ALT 1.313,2.094 1.729,2.25 0.417,0.156 10 false AM1 2.031,3.49 2.427,3.646 0.396,0.156 10 false AM2 3.073,5.146 3.344,5.302 0.271,0.156 10 false D6 2.5,5.177 2.656,5.344 0.156,0.167 10 false 1 3.375,5.146 3.531,5.313 0.156,0.167 10 false 1 3.573,2.385 3.729,2.552 0.156,0.167 10 false 1 3.583,2.844 3.74,3.01 0.156,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Read the values.


f.

Check the result when the ignition switch is turned to ON and when the engine is started.

Standard:
Ignition Switch Position Display (Starter Signal)
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

2.INSPECT STARTER RELAY (ST)

NG

6.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH POWER SOURCE)
2.INSPECT STARTER RELAY (ST)
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STARTER RELAY - IGNITION SWITCH AND BODY GROUND, STARTER RELAY - STARTER)

NG

REPLACE STARTER RELAY (ST)

3.CHECK HARNESS AND CONNECTOR (STARTER RELAY - IGNITION SWITCH AND BODY GROUND, STARTER RELAY - STARTER)
a.

Disconnect the ignition switch connector.


b.

Disconnect the starter connector.


c.

Remove the starter relay (ST) from the engine room R/B assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
L21-3 (ST1) - ST relay terminal 1 Always Below 1 Ω
D6-1 - ST relay terminal 3 Always Below 1 Ω
ST relay terminal 2 - Body ground Always Below 1 Ω
L21-3 (ST1) or ST relay terminal 1 - Body ground Always 10 kΩ or higher
D6-1 or ST relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.

Remove the starter relay (ST) from the engine room R/B assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
ST relay terminal 5 - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
ST relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT STARTER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STARTER

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER - STARTER RELAY (ST), BATTERY)

NG

6.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH POWER SOURCE)
a.
A404953C01
0.271,1.073 0.677,1.396 0.406,0.323 2.635,1.771 2.24,1.125 true 2.552,1.792 3.01,1.99 0.458,0.198 10 false AM1 0.115,0.115 0.573,0.313 0.458,0.198 10 false *a 0.365,1.156 0.823,1.354 0.458,0.198 10 false L21
*a Component without harness connected
(Ignition Switch)


Disconnect the ignition switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
L21-4 (AM1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT IGNITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY POSITIVE TERMINAL)

7.INSPECT IGNITION SWITCH

Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
a.

Disconnect the ignition switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for RHD
Tester Connection Condition Specified Condition
L21-3 (ST1) - A29-48 (STA) Always Below 1 Ω
L21-3 (ST1) or A29-48 (STA) - Body ground Always 10 kΩ or higher


Standard resistance:
for LHD
Tester Connection Condition Specified Condition
L21-3 (ST1) - I84-48 (STA) Always Below 1 Ω
L21-3 (ST1) or I84-48 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR