Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2022.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0627  Fuel Pump Control Circuit / Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0627 Fuel Pump Control Circuit / Open Open or short in suction control valve circuit for more than 0.5 seconds
(1 trip detection logic)
·

Open or short in suction control valve circuit

·

Suction control valve

·

Fuel temperature sensor, suction control valve wire

·

ECM


Comes on DTC stored

HINT:
·

For more information on the fuel supply pump (suction control valve) and the common rail system, refer to the system description.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION

·

When DTC P0627 is set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Common Rail Pressure.



Reference
Engine Speed Common Rail Pressure
Idling Approximately 27000 to 45000 kPa
3000 rpm (No engine load) Approximately 55000 to 75000 kPa

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0627 Idling for 1 second

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL SUPPLY PUMP (SUCTION CONTROL VALVE)
a.
A168115C04
1.021,1.427 1.5,1.729 0.479,0.302 1.885,1.427 2.365,1.729 0.479,0.302 1.885,2.271 2.5,2.052 true 1.552,2.281 0.938,2.052 true 0.135,0.073 0.427,0.344 0.292,0.271 10 false *a 1.177,1.5 1.469,1.667 0.292,0.167 10 false rC2 0.531,1.969 0.875,2.167 0.344,0.198 10 false PCV 2.563,1.969 2.802,2.135 0.24,0.167 10 false +B 2.031,1.49 2.323,1.656 0.292,0.167 10 false rC1 1.188,1.76 1.531,1.958 0.344,0.198 10 false *A 2.073,1.75 2.417,1.948 0.344,0.198 10 false *B
*A for RHD
*B for LHD
*a Component without harness connected
(Fuel Temperature Sensor, Suction Control Valve)


Disconnect the fuel temperature sensor, suction control valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for RHD
Tester Connection Condition Specified Condition
rC2-1 (PCV) - rC2-2 (+B) 20°C (68°F) 1.9 to 2.3 Ω


Standard resistance:
for LHD
Tester Connection Condition Specified Condition
rC1-1 (PCV) - rC1-2 (+B) 20°C (68°F) 1.9 to 2.3 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE - ECM)

NG

5.CHECK FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE
2.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE - ECM)
a.
A311457C11
1.177,0.396 1.594,0.646 0.417,0.25 1.25,2.333 1.667,2.583 0.417,0.25 1.927,0.406 2.344,0.656 0.417,0.25 1.083,1.021 1.521,1.188 true 2.313,1.042 1.938,1.208 true 1.542,4.177 2,3.698 true 2.302,4.188 2.083,3.688 true 0.167,0.104 0.479,0.26 0.313,0.156 10 false *a 0.167,2.135 0.479,2.292 0.313,0.156 10 false *b 1.333,2.375 1.646,2.531 0.313,0.156 10 false C39 0.833,0.927 1.146,1.083 0.313,0.156 10 false +B 2.385,0.948 2.698,1.104 0.313,0.156 10 false PCV 2.063,4.229 2.844,4.448 0.781,0.219 10 false 105 (PCV-) 1.188,4.229 2.052,4.438 0.865,0.208 10 false 104 (PCV+) 2.042,0.448 2.354,0.604 0.313,0.156 10 false rC1 1.281,0.438 1.594,0.594 0.313,0.156 10 false rC2 1.302,0.667 1.615,0.823 0.313,0.156 10 false *A 2.083,0.688 2.396,0.844 0.313,0.156 10 false *B
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to Fuel Temperature Sensor, Suction Control Valve)
*b Front view of wire harness connector
(to ECM)


Disconnect the fuel temperature sensor, suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for RHD
Tester Connection Condition Specified Condition
rC2--1 (PCV) - C39-105 (PCV-) Always Below 1 Ω
rC2--2 (+B) - C39-104 (PCV+) Always Below 1 Ω
rC2--1 (PCV) or C39-105 (PCV-) - Body ground Always 10 kΩ or higher
rC2--2 (+B) or C39-104 (PCV+) - Body ground Always 10 kΩ or higher


Standard resistance:
for LHD
Tester Connection Condition Specified Condition
rC1--1 (PCV) - C39-105 (PCV-) Always Below 1 Ω
rC1--2 (+B) - C39-104 (PCV+) Always Below 1 Ω
rC1--1 (PCV) or C39-105 (PCV-) - Body ground Always 10 kΩ or higher
rC1--2 (+B) or C39-104 (PCV+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the ignition switch to ON and wait for approximately 1 minute.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs.

Result:
Result Proceed to
P0627 is output A
No output is output B




A

B

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE
a.
A311458C04
0.573,0.781 0.948,1 0.375,0.219 0.958,3.854 1.333,4.073 0.375,0.219 0.958,3.427 1.333,3.646 0.375,0.219 1.292,3.25 1.74,3.479 true 2.521,3.25 2.115,3.49 true 1.323,1 1.021,1.354 true 1.563,1.01 1.865,1.333 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.708,0.813 0.906,0.969 0.198,0.156 10 false r2 1.042,3.885 1.323,4.063 0.281,0.177 10 false rC1 0.979,3.156 1.292,3.354 0.313,0.198 10 false PCV 2.563,3.156 2.875,3.354 0.313,0.198 10 false +B 0.906,1.385 1.219,1.583 0.313,0.198 10 false +B 1.719,1.385 2.031,1.583 0.313,0.198 10 false PCV 1.073,4.094 1.385,4.292 0.313,0.198 10 false *B 1.083,3.667 1.396,3.865 0.313,0.198 10 false *A 1.052,3.458 1.333,3.635 0.281,0.177 10 false rC2
*A for RHD
*B for LHD
*a Component without harness connected
(Fuel Temperature Sensor, Suction Control Valve)


Remove the fuel temperature sensor, suction control valve wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for RHD
Tester Connection Condition Specified Condition
r2-1 (+B) - rC2-2 (+B) Always Below 1 Ω
r2-2 (PCV) - rC2-1 (PCV) Always Below 1 Ω
r2-1 (+B) or rC2-2 (+B) - Body ground Always 10 kΩ or higher
r2-2 (PCV) or rC2-1 (PCV) - Body ground Always 10 kΩ or higher


Standard resistance:
for LHD
Tester Connection Condition Specified Condition
r2-1 (+B) - rC1-2 (+B) Always Below 1 Ω
r2-2 (PCV) - rC1-1 (PCV) Always Below 1 Ω
r2-1 (+B) or rC1-2 (+B) - Body ground Always 10 kΩ or higher
r2-2 (PCV) or rC1-1 (PCV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE FUEL SUPPLY PUMP

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE FUEL SUPPLY PUMP

Result:
Proceed to
NEXT



NEXT

7.BLEED AIR FROM FUEL SYSTEM
7.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM (w/ DPF)>ON-VEHICLE INSPECTION

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



Result:
Proceed to
NEXT



NEXT

8.PERFORM SUPPLY PUMP INITIALIZATION
8.PERFORM SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the engine switch off for 30 seconds or more.


d.

Start the engine and idle it for 1 second or more.


e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED