The headlight ECU sub-assembly operates using the power source voltage input from the IG terminal and ECUB terminal.
The power source voltage of the ECUB terminal is supplied when the main body ECU (multiplex network body ECU) turns the ECUB power supply relay (H-LP LH relay and H-LP RH relay) to ON.
The headlight ECU sub-assembly compares the power source voltage supply condition of the IG terminal and ECUB terminal and monitors the result.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B242F | Open in B Power Line | Detection condition:
Ignition switch ON Malfunction status:
No power source voltage supplied to ECUB terminal while power source voltage being supplied to IG terminal Malfunction duration:
10 seconds or more |
·
Headlight ECU sub-assembly LH ·
H-LP LH relay ·
Main body ECU (multiplex network body ECU) ·
Driver side junction block assembly ·
Harness or connector |
AFS | A | w/ Adaptive High Beam System |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B242F | Open in B Power Line | Detection condition:
Ignition switch ON Malfunction status:
No power source voltage supplied to ECUB terminal while power source voltage being supplied to IG terminal Malfunction duration:
10 seconds or more |
·
Headlight ECU sub-assembly RH ·
H-LP RH relay ·
Main body ECU (multiplex network body ECU) ·
Harness or connector |
AFS (Sub) | A | w/ Adaptive High Beam System |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B242F | Open in B Power Line | Detection condition:
Ignition switch ON Malfunction status:
No power source voltage supplied to ECUB terminal while power source voltage being supplied to IG terminal Malfunction duration:
10 seconds or more |
·
Headlight ECU sub-assembly LH ·
H-LP LH relay ·
Main body ECU (multiplex network body ECU) ·
Driver side junction block assembly ·
Harness or connector |
HL AutoLeveling | A | w/o Adaptive High Beam System |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B242F | Open in B Power Line | Detection condition:
Ignition switch ON Malfunction status:
No power source voltage supplied to ECUB terminal while power source voltage being supplied to IG terminal Malfunction duration:
10 seconds or more |
·
Headlight ECU sub-assembly RH ·
H-LP RH relay ·
Main body ECU (multiplex network body ECU) ·
Harness or connector |
HL AutoLeveling (Sub) | A | w/o Adaptive High Beam System |
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>REGISTRATION
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
First, confirm that there is no malfunction in the power integration system. Refer to the How to Proceed with Troubleshooting procedure.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/ Adaptive High Beam System | A |
| w/o Adaptive High Beam System | B |
A
B
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Pre-procedure1
Turn the ignition switch ON and wait for at least 10 seconds or more.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only B242F for AFS is output | A |
| Only B242F for AFS (Sub) is output | B |
| None of the above conditions are met | C |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Headlight ECU sub-assembly LH | AFS | B242F | Open in B Power Line |
| Headlight ECU sub-assembly RH | AFS (Sub) | B242F | Open in B Power Line |
Post-procedure1
None
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-procedure1
Disconnect the A26 headlight ECU sub-assembly LH connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A26)Location & Routingewd_type=routing;type=c;code=A26 |
||
| A26-13 (ECUB) - Body ground | Ignition switch ON | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the A26 headlight ECU sub-assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A26)Location & Routingewd_type=routing;type=c;code=A26 |
||
| A26-13 (ECUB) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
OK
NG
Pre-procedure1
Remove the H-LP LH relay.
Procedure1
| *a | Front view of wire harness connector
(to H-LP LH Relay) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (H-LP LH relay) - Body ground | Ignition switch off | 11 to 14 V |
| 3 (H-LP LH relay) - Body ground | Ignition switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the H-LP LH relay.
Disconnect the A26 headlight ECU sub-assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A26)Location & Routingewd_type=routing;type=c;code=A26 |
||
| 5 (H-LP LH relay) - A26-13 (ECUB) | Always | Below 1 Ω |
| 5 (H-LP LH relay) or A26-13 (ECUB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Pre-procedure1
Remove the H-LP LH relay.
Disconnect the 4F driver side junction block assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (H-LP LH relay) - 4F-19 | Always | Below 1 Ω |
| 2 (H-LP LH relay) or 4F-19 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4F-19 - A-15 (HRLY) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the H-LP LH relay.
Disconnect the 4F driver side junction block assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (H-LP LH relay) - 4F-20 | Always | Below 1 Ω |
| 2 (H-LP LH relay) or 4F-20 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4F-20 - A-15 (HRLY) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the A27 headlight ECU sub-assembly RH connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A27)Location & Routingewd_type=routing;type=c;code=A27 |
||
| A27-13 (ECUB) - Body ground | Ignition switch ON | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the A27 headlight ECU sub-assembly RH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A27)Location & Routingewd_type=routing;type=c;code=A27 |
||
| A27-13 (ECUB) - Body ground | Always | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
OK
NG
Pre-procedure1
Remove the H-LP RH relay.
Procedure1
| *a | Front view of wire harness connector
(to H-LP RH Relay) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (H-LP RH relay) - Body ground | Ignition switch off | 11 to 14 V |
| 5 (H-LP RH relay) - Body ground | Ignition switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the H-LP RH relay.
Disconnect the A27 headlight ECU sub-assembly RH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A27)Location & Routingewd_type=routing;type=c;code=A27 |
||
| 3 (H-LP RH relay) - A27-13 (ECUB) | Always | Below 1 Ω |
| 3 (H-LP RH relay) or A27-13 (ECUB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the H-LP RH relay.
Disconnect the D11 main body ECU (multiplex network body ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D11)Location & Routingewd_type=routing;type=c;code=D11 Click Connector(D11)Instrument Panel>Instrument Panel Wire>Main Body ECUewd_type=component;type=c;code=D11;pinno=12 |
||
| 2 (H-LP RH relay) - D11-12 (HRY2) | Always | Below 1 Ω |
| 2 (H-LP RH relay) or D11-12 (HRY2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Pre-procedure1
Turn the ignition switch ON and wait for at least 10 seconds or more.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only B242F for HL AutoLeveling is output | A |
| Only B242F for HL AutoLeveling (Sub) is output | B |
| None of the above conditions are met | C |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Headlight ECU sub-assembly LH | HL AutoLeveling | B242F | Open in B Power Line |
| Headlight ECU sub-assembly RH | HL AutoLeveling (Sub) | B242F | Open in B Power Line |
Post-procedure1
None
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING