The headlight ECU sub-assembly controls the high beam headlights.
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>REGISTRATION
Check the illumination of each high beam lights.
| Result | Proceed to |
|---|---|
| LH side high beam light does not illuminate. | A |
| RH side high beam light does not illuminate. | B |
A
B
Using the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Headlight High Beam | High beam headlights | OFF or ON | - |
| Tester Display |
|---|
| Headlight High Beam |
High beam headlights turn on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the headlight unit assembly LH with RH and connect the connectors to them.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL
Check that the high beam light LH operate normally.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| LH side high beam light does not illuminate. | A |
| RH side high beam light does not illuminate. | B |
A
B
Remove the headlight unit LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Remove the headlight unit assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
| *a | Component without harness connected
(Headlight Unit Assembly LH) |
| *b | Component without harness connected
(Headlight Unit LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-11- D-2 | Always | Below 1 Ω |
| B-20 - D-3 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Headlight High Beam | High beam headlights | OFF or ON | - |
| Tester Display |
|---|
| Headlight High Beam |
High beam headlights turn on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the headlight unit assembly RH with LH and connect the connectors to them.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL
Check that the high beam light RH operate normally.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| RH side high beam light does not illuminate. | A |
| LH side high beam light does not illuminate. | B |
A
B
Remove the headlight unit RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Remove the headlight unit assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
| *a | Component without harness connected
(Headlight Unit Assembly LH) |
| *b | Component without harness connected
(Headlight Unit LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-11- D-2 | Always | Below 1 Ω |
| B-20 - D-3 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG