Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE
RM37H0E _52 Drivetrain _095769 AXLE AND DIFFERENTIAL _0452038 STEERING KNUCKLE A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C446765N03
2.333,1.167 2.479,1.167 2.479,1.167 2.563,0.646 true 2.167,4.75 2.333,4.75 2.333,4.75 2.49,4.333 true 5.771,4.333 6.083,4.333 true 3.802,0.531 4.115,0.531 true 4.167,3.333 4.333,3.667 4.333,3.667 4.5,3.667 true 4.417,1.677 4.729,1.677 true 3.042,2.01 3.208,2.01 true 2.813,2.719 3.125,2.719 true 2.135,2.917 2.302,2.917 2.302,2.917 2.458,2.5 true 6.156,4.177 6.51,4.469 0.354,0.292 18 false 1 4.594,3.5 5.229,3.833 0.635,0.333 18 false 4, 7 1.958,4.604 2.281,4.927 0.323,0.323 18 false 3 3.656,5.344 3.927,5.594 0.271,0.25 10 false x 3 2.115,1.031 2.396,1.313 0.281,0.281 18 false 5 4.219,0.375 4.5,0.729 0.281,0.354 18 false 6 4.823,1.573 5.104,1.927 0.281,0.354 10 false ● 2.875,1.917 3.156,2.271 0.281,0.354 10 false ● 2.667,2.604 2.917,2.833 0.25,0.229 10 false ● 1.906,2.781 2.198,3.094 0.292,0.313 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT AXLE HUB SUB-ASSEMBLY LH 43502C - - -
2 FRONT FLEXIBLE HOSE BRACKET LH 47352 - - -
3 TIE ROD ASSEMBLY LH 45470 (Click here) - -
4 LOOSEN STEERING KNUCKLE LH 43212 - - -
5 FRONT UPPER NO. 1 SUSPENSION ARM ASSEMBLY LH 48630D (Click here) - -
6 FRONT UPPER NO. 2 SUSPENSION ARM ASSEMBLY LH 48630E - - -
7 REMOVE STEERING KNUCKLE LH 43212 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the steering knuckle removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link

*: The vehicle height changes because of suspension or tire replacement.

Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA Parking assist- sensor system

·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assisr ECU initilization

·

Adjust sttering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43502C 1.REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH

Hide 47352 2.REMOVE FRONT FLEXIBLE HOSE BRACKET LH

a.
C447773


Hide 45470 3.DISCONNECT TIE ROD ASSEMBLY LH

Z101186

Click here(Click here)

Hide 43212 4.LOOSEN STEERING KNUCKLE LH

a.
C446766


Hide 48630D 5.DISCONNECT FRONT UPPER NO. 1 SUSPENSION ARM ASSEMBLY LH

Z101186

Click here(Click here)

Hide 48630E 6.DISCONNECT FRONT UPPER NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Perform the same procedure as for the front upper No. 1 suspension arm assembly LH.


Hide 43212 7.REMOVE STEERING KNUCKLE LH

a.
C446766