Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB
RM37H0E _52 Drivetrain _095769 AXLE AND DIFFERENTIAL _0452040 REAR AXLE HUB G

AXLE AND DIFFERENTIAL  REAR AXLE HUB  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced when performing the rear axle hub inspection are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Rear disc (Including removal and installation)

·

Parking brake shoe (Including removal and installation)


Parking brake bedding Electric parking brake system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced when performing the rear axle hub inspection are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
·

Rear disc (Including removal and installation)

·

Parking brake shoe (Including removal and installation)


Parking brake bedding Electric parking brake system (Click here)
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISABLE BRAKE CONTROL

Hide 3.REMOVE REAR WHEEL

Hide 47850 4.DISCONNECT REAR DISC BRAKE CYLINDER ASSEMBLY

Hide 42491 5.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 42432 6.REMOVE REAR DISC LH

Hide 7.INSPECT REAR AXLE HUB BEARING LOOSENESS

a.
C385014

Using a dial indicator, check for looseness near the center of the rear axle hub.

Maximum Looseness:
Specified Condition
0.05 mm
0.00197 in.


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Keep the magnet of the dial indicator away from the rear axle hub and bearing assembly.



If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.


Hide 8.INSPECT REAR AXLE HUB RUNOUT

a.
C385015

Using a dial indicator, check for runout on the surface of the rear axle hub outside the rear axle hub bolts.

Maximum Runout:
Specified Condition
0.05 mm
0.00197 in.


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Make sure to install the tip of the dial indicator towards the outside of the rear axle hub bolts.

·

Keep the magnet of the dial indicator away from the rear axle hub and bearing assembly.



If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.


Hide 42432 9.INSTALL REAR DISC LH

Hide 42491 10.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 47850 11.CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY

Hide 12.ADJUST PARKING BRAKE

Hide 13.INSTALL REAR WHEEL

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 15. PERFORM PARKING BRAKE SHOE BEDDING

Hide 16. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

HINT:

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE


HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART