Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM37H0E _58 Vehicle Interior _095313 DOOR LOCK _0452394 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Double Lock Function does not Operate Properly  


DESCRIPTION

All the doors except the luggage compartment door have the double lock function. This system is set and unset by the main body ECU. When the main body ECU sends a request signal to each door ECU to set or unset the double lock function, the double lock motor built into each door lock operates.

WIRING DIAGRAM

B494179E03
1.896,4.188 3.552,4.583 1.656,0.396 10 false Front Multiplex Network Door ECU LH 3.802,4.167 5.292,4.708 1.49,0.542 10 false Front Multiplex Network Door ECU RH 1.99,7.615 3.458,7.969 1.469,0.354 10 false Rear Multiplex Network Door ECU LH 3.927,7.646 5.396,8 1.469,0.354 10 false Rear Multiplex Network Door ECU RH 0.625,8.406 2.458,8.583 1.833,0.177 10 false : CAN Communication Line 4.031,1.344 6.927,1.667 2.896,0.323 10 false Main Body ECU (Multiplex Network Body ECU) 0.063,4.177 1.76,4.531 1.698,0.354 10 false Front Door with Motor Lock Assembly LH 5.646,4.167 7.094,4.719 1.448,0.552 10 false Front Door with Motor Lock Assembly RH 0.354,7.625 1.323,8.021 0.969,0.396 10 false Rear Door Lock Assembly LH 5.875,7.667 6.844,8.063 0.969,0.396 10 false Rear Door Lock Assembly RH 1.896,4.01 2.302,4.219 0.406,0.208 10 false E24 1.156,2.229 1.563,2.438 0.406,0.208 10 false DL 2.177,3.104 2.583,3.313 0.406,0.208 10 false DBLS 2.188,2.708 2.594,2.917 0.406,0.208 10 false A1- 2.177,3.51 2.583,3.719 0.406,0.208 10 false DBE 1.99,3.417 2.396,3.625 0.406,0.208 10 false 4 1.948,3.021 2.354,3.229 0.406,0.208 10 false 24 1.99,2.229 2.396,2.438 0.406,0.208 10 false 5 1.99,2.604 2.396,2.813 0.406,0.208 10 false 6 0.073,4.01 0.479,4.219 0.406,0.208 10 false E21 1.438,2.219 1.844,2.427 0.406,0.208 10 false 4 1.427,2.594 1.833,2.802 0.406,0.208 10 false 3 2.177,2.323 2.583,2.531 0.406,0.208 10 false A1+ 0.979,2.594 1.385,2.802 0.406,0.208 10 false UNDL 0.979,3.021 1.385,3.229 0.406,0.208 10 false DLSR 1.229,3.417 1.635,3.625 0.406,0.208 10 false E 1.427,3.021 1.833,3.229 0.406,0.208 10 false 6 1.427,3.417 1.833,3.625 0.406,0.208 10 false 5 5.885,7.5 6.292,7.708 0.406,0.208 10 false F2 4.75,6.563 5.156,6.771 0.406,0.208 10 false DBLS 4.74,6.979 5.146,7.188 0.406,0.208 10 false DLE1 4.865,6.177 5.271,6.385 0.406,0.208 10 false A1- 4.844,5.792 5.25,6 0.406,0.208 10 false A1+ 5.938,5.698 6.344,5.906 0.406,0.208 10 false DL 5.948,6.083 6.354,6.292 0.406,0.208 10 false UNDL 5.927,6.5 6.333,6.708 0.406,0.208 10 false DLSR 5.958,6.896 6.365,7.104 0.406,0.208 10 false E 5.708,6.896 6.115,7.104 0.406,0.208 10 false 10 5.76,6.5 6.167,6.708 0.406,0.208 10 false 9 5.76,5.688 6.167,5.896 0.406,0.208 10 false 4 5.75,6.083 6.156,6.292 0.406,0.208 10 false 3 5.167,5.688 5.573,5.896 0.406,0.208 10 false 5 5.177,6.094 5.583,6.302 0.406,0.208 10 false 6 5.177,6.896 5.583,7.104 0.406,0.208 10 false 4 5.156,6.5 5.563,6.708 0.406,0.208 10 false 24 2.167,6.573 2.573,6.781 0.406,0.208 10 false DBLS 2.177,6.99 2.583,7.198 0.406,0.208 10 false DLE1 1.979,6.896 2.385,7.104 0.406,0.208 10 false 4 1.948,6.5 2.354,6.708 0.406,0.208 10 false 24 2.188,6.167 2.594,6.375 0.406,0.208 10 false A1- 2.188,5.781 2.594,5.99 0.406,0.208 10 false A1+ 2,5.708 2.406,5.917 0.406,0.208 10 false 5 2,6.083 2.406,6.292 0.406,0.208 10 false 6 0.354,7.458 0.76,7.667 0.406,0.208 10 false F13 3.927,7.469 4.333,7.677 0.406,0.208 10 false F4 2,7.448 2.406,7.656 0.406,0.208 10 false F15 0.958,6.5 1.365,6.708 0.406,0.208 10 false DLSR 1.219,6.896 1.625,7.104 0.406,0.208 10 false E 0.969,6.094 1.375,6.302 0.406,0.208 10 false UNDL 1.177,5.698 1.583,5.906 0.406,0.208 10 false DL 1.417,5.708 1.823,5.917 0.406,0.208 10 false 2 1.417,6.094 1.823,6.302 0.406,0.208 10 false 1 1.417,6.885 1.823,7.094 0.406,0.208 10 false 6 1.427,6.5 1.833,6.708 0.406,0.208 10 false 5 4.854,2.323 5.26,2.531 0.406,0.208 10 false A1+ 4.844,2.698 5.25,2.906 0.406,0.208 10 false A1- 4.74,3.115 5.146,3.323 0.406,0.208 10 false DBLS 4.76,3.479 5.167,3.688 0.406,0.208 10 false DBE 5.208,3.417 5.615,3.625 0.406,0.208 10 false 4 5.177,3.01 5.583,3.219 0.406,0.208 10 false 24 5.208,2.615 5.615,2.823 0.406,0.208 10 false 6 5.208,2.229 5.615,2.438 0.406,0.208 10 false 5 5.948,2.208 6.354,2.417 0.406,0.208 10 false DL 5.938,2.594 6.344,2.802 0.406,0.208 10 false UNDL 5.938,3.021 6.344,3.229 0.406,0.208 10 false DLSR 5.938,3.406 6.344,3.615 0.406,0.208 10 false E 5.75,3.021 6.156,3.229 0.406,0.208 10 false 9 5.708,3.406 6.115,3.615 0.406,0.208 10 false 10 5.74,2.615 6.146,2.823 0.406,0.208 10 false 1 5.75,2.24 6.156,2.448 0.406,0.208 10 false 2 5.667,4.021 6.073,4.229 0.406,0.208 10 false E3 3.792,3.979 4.198,4.188 0.406,0.208 10 false E6

CAUTION / NOTICE / HINT

NOTICE:
·

The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the doors can be locked and unlocked normally using the wireless operation.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Doors can be locked and unlocked normally using wireless operation.



Result:
Proceed to
OK
NG



OK

2.CHECK DOUBLE LOCK OPERATION

NG

2.CHECK DOUBLE LOCK OPERATION

Result:
Result Proceed to
All doors cannot be double-locked or double-unlocked. A
Only front left door cannot be double-locked or double-unlocked. B
Only front right door cannot be double-locked or double-unlocked. C
Only rear left door cannot be double-locked or double-unlocked. D
Only rear right door cannot be double-locked or double-unlocked. E



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

3.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH

C

5.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH

D

7.INSPECT REAR DOOR LOCK ASSEMBLY LH

E

9.INSPECT REAR DOOR LOCK ASSEMBLY RH
3.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH - FRONT MULTIPLEX NETWORK DOOR ECU LH)

NG

REPLACE FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH - FRONT MULTIPLEX NETWORK DOOR ECU LH)
a.

Disconnect the E21 front door with motor lock assembly LH connector.


b.

Disconnect the E24 front multiplex network door ECU LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E21,E24)Location & Routing

Click Connector(E21)Body>Front Door Wire LH / Front Door Wire RH>Front Door Lock with Motor Assembly LH

Click Connector(E24)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU LH

E21-4 (DL) - E24-5 (A1+) Always Below 1 Ω
E21-3 (UNDL) - E24-6 (A1-) Always Below 1 Ω
E21-6 (DLSR) - E24-24 (DBLS) Always Below 1 Ω
E21-5 (E) - E24-4 (DBE) Always Below 1 Ω
E21-4 (DL) or E24-5 (A1+) - Other terminals and body ground Always 10 kΩ or higher
E21-3 (UNDL) or E24-6 (A1-) - Other terminals and body ground Always 10 kΩ or higher
E21-6 (DLSR) or E24-24 (DBLS) - Other terminals and body ground Always 10 kΩ or higher
E21-5 (E) or E24-4 (DBE) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH - FRONT MULTIPLEX NETWORK DOOR ECU RH)

NG

REPLACE FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH

6.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH - FRONT MULTIPLEX NETWORK DOOR ECU RH)
a.

Disconnect the E3 front door with motor lock assembly RH connector.


b.

Disconnect the E6 front multiplex network door ECU RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E3,E6)Location & Routing

Click Connector(E3)Body>Front Door Wire LH / Front Door Wire RH>Front Door Lock with Motor Assembly RH

Click Connector(E6)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU RH

E3-2 (DL) - E6-5 (A1+) Always Below 1 Ω
E3-1 (UNDL) - E6-6 (A1-) Always Below 1 Ω
E3-9 (DLSR) - E6-24 (DBLS) Always Below 1 Ω
E3-10 (E) - E6-4 (DBE) Always Below 1 Ω
E3-2 (DL) or E6-5 (A1+) - Other terminals and body ground Always 10 kΩ or higher
E3-1 (UNDL) or E6-6 (A1-) - Other terminals and body ground Always 10 kΩ or higher
E3-9 (DLSR) or E6-24 (DBLS) - Other terminals and body ground Always 10 kΩ or higher
E3-10 (E) or E6-4 (DBE) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT REAR DOOR LOCK ASSEMBLY LH

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY LH - REAR MULTIPLEX NETWORK DOOR ECU LH)

NG

REPLACE REAR DOOR LOCK ASSEMBLY LH

8.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY LH - REAR MULTIPLEX NETWORK DOOR ECU LH)
a.

Disconnect the F13 rear door lock assembly LH connector.


b.

Disconnect the F15 rear multiplex network door ECU LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F13,F15)Location & Routing

Click Connector(F13)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

Click Connector(F15)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU LH

F13-2 (DL) - F15-5 (A1+) Always Below 1 Ω
F13-1 (UNDL) - F15-6 (A1-) Always Below 1 Ω
F13-5 (DLSR) - F15-24 (DBLS) Always Below 1 Ω
F13-6 (E) - F15-4 (DLE1) Always Below 1 Ω
F13-2 (DL) or F15-5 (A1+) - Other terminals and body ground Always 10 kΩ or higher
F13-1 (UNDL) or F15-6 (A1-) - Other terminals and body ground Always 10 kΩ or higher
F13-5 (DLSR) or F15-24 (DBLS) - Other terminals and body ground Always 10 kΩ or higher
F13-6 (E) or F15-4 (DLE1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT REAR DOOR LOCK ASSEMBLY RH

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY RH - REAR MULTIPLEX NETWORK DOOR ECU RH)

NG

REPLACE REAR DOOR LOCK ASSEMBLY RH

10.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY RH - REAR MULTIPLEX NETWORK DOOR ECU RH)
a.

Disconnect the F2 rear door lock assembly RH connector.


b.

Disconnect the F4 rear multiplex network door ECU RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F2,F4)Location & Routing

Click Connector(F2)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly RH

Click Connector(F4)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU RH

F2-4 (DL) - F4-5 (A1+) Always Below 1 Ω
F2-3 (UNDL) - F4-6 (A1-) Always Below 1 Ω
F2-9 (DLSR) - F4-24 (DBLS) Always Below 1 Ω
F2-10 (E) - F4-4 (DLE1) Always Below 1 Ω
F2-4 (DL) or F4-5 (A1+) - Other terminals and body ground Always 10 kΩ or higher
F2-3 (UNDL) or F4-6 (A1-) - Other terminals and body ground Always 10 kΩ or higher
F2-9 (DLSR) or F4-24 (DBLS) - Other terminals and body ground Always 10 kΩ or higher
F2-10 (E) or F4-4 (DLE1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE REAR MULTIPLEX NETWORK DOOR ECU RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR