Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM C

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P176087  Lost Communication with Sub Battery Module Missing Message  


DESCRIPTION

The shift control ECU sends backup request signals to the shift control supply according to BUBO signals.

The shift control ECU receives backup mode and malfunction notification signals from the shift control supply according to BUBI signals.

Communication is performed using PWM communication (Pulse Width Modulation: Modulates pulse width according to duty ratio).

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P176087 Lost Communication with Sub Battery Module Missing Message 0.5 seconds or more elapse after turning ignition switch to ON with auxiliary battery voltage 10 V or higher, shift control ECU is unable to receive signals from shift control supply continuously for 1 second or more
(1 trip detection logic)
·

Shift control ECU

·

Shift control supply

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 2 minutes or more.


WIRING DIAGRAM

C450322E01
1.635,0.552 2.094,0.75 0.458,0.198 10 false 12 V 0.896,3.052 1.208,3.25 0.313,0.198 10 false G12 0.896,3.229 3.198,3.417 2.302,0.188 10 false Shift Control Supply 2.573,1.906 2.865,2.073 0.292,0.167 10 false RO 2.896,1.896 3.135,2.094 0.24,0.198 10 false 3 4.646,1.896 5.073,2.052 0.427,0.156 10 false BUBI 4.333,1.896 4.656,2.104 0.323,0.208 10 false 22 4.792,3.042 5.115,3.219 0.323,0.177 10 false D92 4.792,3.219 6.781,3.448 1.99,0.229 10 false Shift Control ECU 0.563,2.417 0.719,2.615 0.156,0.198 10 false 2 0.833,2.552 1.292,2.75 0.458,0.198 10 false GND 2.417,1.656 3.031,1.854 0.615,0.198 10 false +BAT 2.896,1.573 3.052,1.771 0.156,0.198 10 false 1 4.635,1.677 5.094,1.875 0.458,0.198 10 false BUB 4.333,1.573 4.646,1.771 0.313,0.198 10 false 10 4.646,2.604 4.958,2.802 0.313,0.198 10 false E1 4.385,2.49 4.542,2.688 0.156,0.198 10 false 1 2.594,1.052 2.906,1.25 0.313,0.198 10 false +B 3.26,1.219 4.167,1.427 0.906,0.208 10 false CAPACITOR 3.365,0.927 3.521,1.125 0.156,0.198 10 false 2 3.677,0.927 3.833,1.125 0.156,0.198 10 false 1 2.896,0.938 3.052,1.135 0.156,0.198 10 false 7 2.625,0.531 2.938,0.729 0.313,0.198 10 false IG 2.875,0.427 3.188,0.625 0.313,0.198 10 false 16 4.323,0.698 5.854,0.896 1.531,0.198 10 false IG2 P NO.2 4.385,0.365 4.542,0.563 0.156,0.198 10 false 2 4.677,0.365 4.833,0.563 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION


HINT:

When a malfunction occurs in the shift control supply power source circuit, communication can no longer be established and P176087 is output.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (SHIFT CONTROL ECU CONNECTOR)
a.
for LHD:
C452170

for RHD:
C450295

Check the connector connections and contact pressure of the relevant terminals for the shift control ECU connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT CONTROL SUPPLY)

NG

CONNECT SECURELY

2.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT CONTROL SUPPLY)

Pre-procedure1

a.

Disconnect the D92 shift control ECU connector.


b.

Disconnect the G12 shift control supply connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D92,G12)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

Click Connector(G12)Instrument Panel>Floor Wire>Shift Control Supply

D92-22 (BUBI) - G12-3 (RO) Always Below 1 Ω
D92-22 (BUBI) or G12-3 (RO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G12 shift control supply connector.


b.

Reconnect the D92 shift control ECU connector.



OK

3.CHECK SHIFT CONTROL ECU (CHECK BUBI TERMINAL WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SHIFT CONTROL ECU (CHECK BUBI TERMINAL WAVEFORM)

Pre-procedure1

a.
C356780C15
0.781,0.313 1.188,0.51 0.406,0.198 0.604,1.781 0.677,1.188 true 1.354,1.781 1.281,1.083 true 0.333,0.292 0.646,0.49 0.313,0.198 10 false *a 0.333,2.219 0.646,2.417 0.313,0.198 10 false *b 2.885,3.5 3.344,3.698 0.458,0.198 10 false GND 0.427,1.823 0.865,1.979 0.438,0.156 10 false BUBI 1.313,1.823 1.75,2.031 0.438,0.208 10 false E1 0.854,0.344 1.469,0.542 0.615,0.198 10 false D92
*a Component with harness connected
(Shift Control ECU)
*b Waveform (Shift control supply condition signal)


Connect an oscilloscope between the shift control ECU terminals specified in the table below.


Procedure1

a.

Turn the ignition switch to ON and measure the waveform.

Tester Connection Condition Equipment Setting

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-22 (BUBI) - D92-1 (E1) Ignition switch ON 10 V/DIV., 10 ms./DIV.

HINT:

The duty ratio changes according to the vehicle condition.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.



OK

NG

4.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT CONTROL SUPPLY)
4.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT CONTROL SUPPLY)

Pre-procedure1

a.

Disconnect the D92 shift control ECU connector.


b.

Disconnect the G12 shift control supply connector.


c.

Remove the IG2 P NO.2 fuse from the luggage room relay block.


d.

Remove the CAPACITOR fuse from the luggage room relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G12,D92)Location & Routing

Click Connector(G12)Instrument Panel>Floor Wire>Shift Control Supply

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

G12-1 (+BAT) - D92-10 (BUB) Always Below 1 Ω
G12-16 (IG) - IG2 P NO.2 fuse terminal 2 Always Below 1 Ω
CAPACITOR fuse terminal 2 - G12-7 (+B) Always Below 1 Ω
G12-2 (GND) - Body ground Always Below 1 Ω
G12-1 (+BAT) or D92-10 (BUB) - Body ground and other terminals Always 10 kΩ or higher
G12-16 (IG) or IG2 P NO.2 fuse terminal 2 - Body ground Always 10 kΩ or higher
CAPACITOR fuse terminal 2 or G12-7 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the CAPACITOR fuse.


b.

Install the IG2 P NO.2 fuse.


c.

Reconnect the G12 shift control supply connector.


d.

Reconnect the D92 shift control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR