Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM C

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P272C73  Park Pawl Motor Relay System Actuator Stuck Closed  


DESCRIPTION

The P CON MTR relay is activated by signals output from the shift control ECU and supplies power to the shift control actuator assembly (parking lock motor).

When the shift control ECU detects a malfunction of the P CON MTR relay, the DTC is stored in the EV control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P272C73 Park Pawl Motor Relay System Actuator Stuck Closed When the P CON MTR relay is off, voltage at terminal MUA, MVA or MWA of the shift control ECU is 3 V or higher for 0.064 seconds or more.
(1 trip detection logic)
·

Shift control ECU

·

P CON MTR relay

·

Shift control actuator assembly

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 10 seconds or more.*

HINT:

*After performing repairs and clearing the DTCs, the P272C73 fail-safe (3-phase motor power source relay OFF) is continued for 1 trip. As a result, P1C8949 may be output. In this case, "Shift system malfunction Apply electric parking brake securely when parking See owner's manual" is displayed on the multi-information display. Therefore, perform the following procedures and clear P1C8949 after restoring normal control.


2.

Operate the electric parking brake, turn the ignition switch off and wait for at least 2 minutes (If the ODO meter is still illuminated after 2 minutes, wait until it turns off).

3.

Turn the ignition switch to ON.

HINT:

If the DTC was cleared during the previous trip, after turning the ignition switch to ON the fail-safe is cleared once normal judgment has been completed.


4.

Depress the brake pedal and move the shift lever to select drive (D).

5.

Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.

CAUTION:

Perform this drive pattern on a level surface and strictly observe the posted speed limits and traffic laws while driving.


6.

Stop the vehicle and push the P position switch (parking switch) to select park (P).

7.

Check that the DTC P272C73 judgment result shows NORMAL by performing the All Readiness check procedure.

8.

Clear the DTCs.

HINT:

If P1C8949 is output at this time, it may be due to the fail-safe.


9.

Turn the ignition switch off and wait for 2 minutes or more (If the ODO meter is still illuminated after 2 minutes, wait until it turns off).

10.

Turn the ignition switch to ON and wait for 10 seconds or more.

11.

Check that there is no DTCs output.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION



PROCEDURE

1.CHECK RELAY VOLTAGE (P CON MTR RELAY)

Pre-procedure1

a.
C453748C01
0.198,0.177 0.51,0.375 0.313,0.198 10 false *1 0.458,1.844 0.771,2.042 0.313,0.198 10 false *2
*1 Luggage Room Relay Block
*2 P CON MTR Relay


Remove the P CON MTR relay from the luggage room relay block.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P CON MTR relay terminal 5 - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the P CON MTR relay.



OK

2.CHECK TERMINAL VOLTAGE (SHIFT CONTROL SUPPLY)

NG

20.CHECK SHIFT CONTROL ECU
2.CHECK TERMINAL VOLTAGE (SHIFT CONTROL SUPPLY)

Pre-procedure1

a.

Disconnect the G12 shift control supply connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G12)Location & Routing

Click Connector(G12)Instrument Panel>Floor Wire>Shift Control Supply

G12-19 (MA2) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G12 shift control supply connector.



OK

3.INSPECT P CON MTR RELAY

NG

13.CHECK SHIFT CONTROL ECU
3.INSPECT P CON MTR RELAY

Pre-procedure1

a.
C453749C01
1.323,2.521 1.99,2.927 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *1 2.104,2.958 2.406,3.188 0.302,0.229 10 false *2
*1 Luggage Room Relay Block
*2 P CON MTR Relay


Remove the P CON MTR relay from the luggage room relay block.


Procedure1

a.
C453750C01
0.094,0.094 0.406,0.292 0.313,0.198 10 false *1
*1 P CON MTR Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the P CON MTR relay.



OK

4.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT CONTROL SUPPLY)

NG

12.REPLACE P CON MTR RELAY
4.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT CONTROL SUPPLY)

Pre-procedure1

a.

Disconnect the G12 shift control supply connector.


b.

Disconnect the D92 shift control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(G12,D92)Location & Routing

Click Connector(G12)Instrument Panel>Floor Wire>Shift Control Supply

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

G12-16 (IG) - IG2 P NO.2 fuse Always Below 1 Ω
G12-14 (RO) - D92-22 (BUBI) Always Below 1 Ω
CAPACITOR fuse terminal 2 - G12-7 (+B) Always Below 1 Ω
G12-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D92 shift control ECU connector.


b.

Reconnect the G12 shift control supply connector.



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - P CON MTR RELAY)

NG

11.REPLACE SHIFT CONTROL SUPPLY
5.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - P CON MTR RELAY)

Pre-procedure1

a.

Disconnect the A44 shift control ECU connector.


b.

Remove the P CON MTR relay from the luggage room relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(A44)Location & Routing

Click Connector(A44)Instrument Panel>Front Compartment Main Wire>Shift Control ECU

A44-12 (BMA1) or P CON MTR relay terminal 1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the P CON MTR relay.


b.

Reconnect the A44 shift control ECU connector.



OK

6.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT CONTROL SUPPLY)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT CONTROL SUPPLY)

Pre-procedure1

a.

Disconnect the D92 shift control ECU connector.


b.

Disconnect the G12 shift control supply connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(D92,G12)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

Click Connector(G12)Instrument Panel>Floor Wire>Shift Control Supply

D92-24 (BMA2) or G12-4 (BMA2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G12 shift control supply connector.


b.

Reconnect the D92 shift control ECU connector.



OK

7.REPLACE SHIFT CONTROL ECU

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE SHIFT CONTROL ECU

NEXT

8.CHECK DTC OUTPUT
8.CHECK DTC OUTPUT
a.

After repairs have been completed, perform the DTC confirmation driving pattern to run the DTC judgment and check that the DTC judgment result shows NORMAL by performing the All Readiness check procedure (Refer to the CONFIRMATION DRIVING PATTERN for DTC P272C73.).

HINT:

After performing repairs and clearing the DTCs, the P272C73 fail-safe (3-phase motor power source relay OFF) is continued for 1 trip. As a result, P1C8949 may be output. In this case, "Shift system malfunction Apply electric parking brake securely when parking See owner's manual" is displayed on the multi-information display. Therefore, turn the ignition switch off and wait for 2 minutes, then turn the ignition switch to ON and clear P1C8949 after restoring normal control.


Result:
Proceed to
NEXT




NEXT

END

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
11.REPLACE SHIFT CONTROL SUPPLY
Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
12.REPLACE P CON MTR RELAY
Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
13.CHECK SHIFT CONTROL ECU

Pre-procedure1

a.

Disconnect the G12 shift control supply connector.


b.

Disconnect the G153 parking lock motor (shift control actuator assembly) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G12)Location & Routing

Click Connector(G12)Instrument Panel>Floor Wire>Shift Control Supply

G12-19 (MA2) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G153 parking lock motor (shift control actuator assembly) connector.


b.

Reconnect the G12 shift control supply connector.



OK

14.REPLACE SHIFT CONTROL ECU

NG

15.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY))
14.REPLACE SHIFT CONTROL ECU

NEXT

8.CHECK DTC OUTPUT
15.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY))

Pre-procedure1

a.

Disconnect the A44 shift control ECU connector.


b.

Disconnect the G153 parking lock motor (shift control actuator assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(A44,G153)Location & Routing

Click Connector(A44)Instrument Panel>Front Compartment Main Wire>Shift Control ECU

Click Connector(G153)Body>Floor Wire / No. 3 Floor Wire>Shift Control Actuator Assembly

A44-5 (MUA) or G153-2 (MUA) - Other terminals Always 10 kΩ or higher
A44-2 (MVA) or G153-6 (MVA) - Other terminals Always 10 kΩ or higher
A44-1 (MWA) or G153-1 (MWA) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G153 parking lock motor (shift control actuator assembly) connector.


b.

Reconnect the A44 shift control ECU connector.



OK

16.CHECK HARNESS AND CONNECTOR (PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY) - P CON MTR RELAY, SHIFT CONTROL SUPPLY)

NG

19.REPAIR OR REPLACE HARNESS OR CONNECTOR
16.CHECK HARNESS AND CONNECTOR (PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY) - P CON MTR RELAY, SHIFT CONTROL SUPPLY)

Pre-procedure1

a.

Disconnect the G153 parking lock motor (shift control actuator assembly) connector.


b.

Remove the P CON MTR relay from the luggage room relay block.


c.

Disconnect the G12 shift control supply connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(G153)Location & Routing

Click Connector(G153)Body>Floor Wire / No. 3 Floor Wire>Shift Control Actuator Assembly

P CON MTR relay terminal 5 or G153-7 (BMA) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G12 shift control supply connector.


b.

Install the P CON MTR relay.


c.

Reconnect the G153 parking lock motor (shift control actuator assembly) connector.



OK

17.REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY

NG

18.REPAIR OR REPLACE HARNESS OR CONNECTOR
17.REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY

NEXT

8.CHECK DTC OUTPUT
18.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
19.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
20.CHECK SHIFT CONTROL ECU

Pre-procedure1

a.
C453748C01
0.198,0.177 0.51,0.375 0.313,0.198 10 false *1 0.458,1.844 0.771,2.042 0.313,0.198 10 false *2
*1 Luggage Room Relay Block
*2 P CON MTR Relay


Remove the P CON MTR relay from the luggage room relay block.


b.

Disconnect the A44 shift control ECU connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P CON MTR relay terminal 5 - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the A44 shift control ECU connector.


b.

Install the P CON MTR relay.



OK

21.REPLACE SHIFT CONTROL ECU

NG

22.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY))
21.REPLACE SHIFT CONTROL ECU

NEXT

8.CHECK DTC OUTPUT
22.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY))

Pre-procedure1

a.

Disconnect the A44 shift control ECU connector.


b.

Disconnect the G153 parking lock motor (shift control actuator assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(A44,G153)Location & Routing

Click Connector(A44)Instrument Panel>Front Compartment Main Wire>Shift Control ECU

Click Connector(G153)Body>Floor Wire / No. 3 Floor Wire>Shift Control Actuator Assembly

A44-5 (MUA) or G153-2 (MUA) - Other terminals Always 10 kΩ or higher
A44-2 (MVA) or G153-6 (MVA) - Other terminals Always 10 kΩ or higher
A44-1 (MWA) or G153-1 (MWA) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G153 parking lock motor (shift control actuator assembly) connector.


b.

Reconnect the A44 shift control ECU connector.



OK

23.CHECK HARNESS AND CONNECTOR (PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY) - P CON MTR RELAY, SHIFT CONTROL SUPPLY)

NG

26.REPAIR OR REPLACE HARNESS OR CONNECTOR
23.CHECK HARNESS AND CONNECTOR (PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY) - P CON MTR RELAY, SHIFT CONTROL SUPPLY)

Pre-procedure1

a.

Disconnect the G153 parking lock motor (shift control actuator assembly) connector.


b.

Remove the P CON MTR relay from the luggage room relay block.


c.

Disconnect the G12 shift control supply connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(G153,G12)Location & Routing

Click Connector(G153)Body>Floor Wire / No. 3 Floor Wire>Shift Control Actuator Assembly

Click Connector(G12)Instrument Panel>Floor Wire>Shift Control Supply

P CON MTR relay terminal 5 or G153-7 (BMA) - Other terminals (except G12-19 (MA2)) Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the P CON MTR relay.


b.

Reconnect the G12 shift control supply connector.


c.

Reconnect the G153 parking lock motor (shift control actuator assembly) connector.



OK

24.REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
24.REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY

NEXT

8.CHECK DTC OUTPUT
25.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
26.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT