The combination meter assembly and EV control ECU detects the rear seat belt state and rear seat occupant state. The rear seat belt warning light illuminates, blinks or turns off in accordance with the vehicle speed, rear seat belt state and rear seat occupant state.
The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Read the Data List according to the display on the GTS.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Right Seat Buckle Switch Status | Rear seat inner belt RH buckle signal | Buckle or Unbuckle | Buckle: Rear RH seat belt fastened
Unbuckle: Rear RH seat belt not fastened |
- |
| Rear Left Seat Buckle Switch Status | Rear seat inner belt LH buckle signal | Buckle or Unbuckle | Buckle: Rear LH seat belt fastened
Unbuckle: Rear LH seat belt not fastened |
- |
| Rear Center Seat Buckle Switch Status | Rear seat inner center belt buckle signal | Buckle or Unbuckle | Buckle: Rear center seat belt fastened
Unbuckle: Rear center seat belt not fastened |
- |
| Tester Display |
|---|
| Rear Right Seat Buckle Switch Status |
| Rear Left Seat Buckle Switch Status |
| Rear Center Seat Buckle Switch Status |
The GTS display changes correctly in response to the rear seat belt buckle switch condition.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Rear RH seat belt malfunction) | B |
| NG (Rear center seat belt malfunction) | C |
| NG (Rear LH seat belt malfunction) | D |
A
B
C
D
Read the Data List according to the display on the GTS.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Right Seat Buckle / Occupant Detection Warning Switch | Rear occupant detection sensor RH signal | ON or OFF | ON: Rear RH seat occupaied
OFF: Rear RH seat not occupaied |
- |
| Rear Left Seat Buckle / Occupant Detection Warning Switch | Rear occupant detection sensor LH signal | ON or OFF | ON: Rear LH seat occupaied
OFF: Rear LH seat not occupaied |
- |
| Rear Center Seat Buckle / Occupant Detection Warning Switch | Rear occupant detection sensor with center signal | ON or OFF | ON: Rear center seat occupaied
OFF: Rear center seat not occupaied |
- |
| Tester Display |
|---|
| Rear Right Seat Buckle / Occupant Detection Warning Switch |
| Rear Left Seat Buckle / Occupant Detection Warning Switch |
| Rear Center Seat Buckle / Occupant Detection Warning Switch |
The GTS display changes correctly in response to the rear seat condition (occupied or unoccupied).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR (for Rear Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M7 rear occupant detection sensor (for LH) connector.
Disconnect the M9 rear occupant detection sensor (for RH) connector.
Disconnect the M8 rear occupant detection sensor (for center) connector.
Disconnect the D41 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(M7,D41)Location & Routingewd_type=routing;type=c,c;code=M7,D41 Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assemblyewd_type=component;type=c;code=D41;pinno=14 |
||
| M7-2 - D41-14 (RLSB) | Always | Below 1 Ω |
| M7-1 - Body ground | Always | Below 1 Ω |
| M7-2 or D41-14 (RLSB) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(M9,D41)Location & Routingewd_type=routing;type=c,c;code=M9,D41 Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assemblyewd_type=component;type=c;code=D41;pinno=12 |
||
| M9-2 - D41-12 (RRSB) | Always | Below 1 Ω |
| M9-1 - Body ground | Always | Below 1 Ω |
| M9-2 or D41-12 (RRSB) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(M8,D41)Location & Routingewd_type=routing;type=c,c;code=M8,D41 Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assemblyewd_type=component;type=c;code=D41;pinno=13 |
||
| M8-2 - D41-13 (RCSB) | Always | Below 1 Ω |
| M8-1 - Body ground | Always | Below 1 Ω |
| M8-2 or D41-13 (RCSB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the rear seat inner with center belt assembly RH connector.
| *a | Front view of wire harness connector
(to Rear Seat Inner with Center Belt Assembly RH) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G77)Location & Routingewd_type=routing;type=c;code=G77 Click Connector(G77)Seat>Floor Wire>Rear Seat Inner Belt with Center Assembly RHewd_type=component;type=c;code=G77;pinno=1 |
||
| G77-1 (RBR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G77 rear seat inner with center belt assembly RH connector.
Disconnect the A16 EV control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G77,A16)Location & Routingewd_type=routing;type=c,c;code=G77,A16 Click Connector(G77)Seat>Floor Wire>Rear Seat Inner Belt with Center Assembly RHewd_type=component;type=c;code=G77;pinno=2 Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECUewd_type=component;type=c;code=A16;pinno=8 |
||
| G77-2 (RBR-) - A16-8 (BRFC) | Always | Below 1 Ω |
| G77-2 (RBR-) or A16-8 (BRFC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the rear inner seat belt assembly LH connector.
| *a | Front view of wire harness connector
(to Rear Seat Inner Belt Assembly LH) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G75)Location & Routingewd_type=routing;type=c;code=G75 Click Connector(G75)Seat>Floor Wire>Rear Seat Inner Belt Assembly LHewd_type=component;type=c;code=G75;pinno=1 |
||
| G75-1 (CBR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G75 rear inner seat belt assembly LH connector.
Disconnect the A16 EV control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G75,A16)Location & Routingewd_type=routing;type=c,c;code=G75,A16 Click Connector(G75)Seat>Floor Wire>Rear Seat Inner Belt Assembly LHewd_type=component;type=c;code=G75;pinno=2 Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECUewd_type=component;type=c;code=A16;pinno=28 |
||
| G75-2 (CBR-) - A16-28 (BCFC) | Always | Below 1 Ω |
| G75-2 (CBR-) or A16-28 (BCFC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the rear inner seat belt assembly LH connector.
| *a | Front view of wire harness connector
(to Rear Seat Inner Belt Assembly LH) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G78)Location & Routingewd_type=routing;type=c;code=G78 Click Connector(G78)Seat>Floor Wire>Rear Seat Inner Belt Assembly LHewd_type=component;type=c;code=G78;pinno=1 |
||
| G78-1 (LBR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G78 rear inner seat belt assembly LH connector.
Disconnect the A16 EV control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G78,A16)Location & Routingewd_type=routing;type=c,c;code=G78,A16 Click Connector(G78)Seat>Floor Wire>Rear Seat Inner Belt Assembly LHewd_type=component;type=c;code=G78;pinno=2 Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECUewd_type=component;type=c;code=A16;pinno=18 |
||
| G78-2 (LBR-) - A16-18 (BLFC) | Always | Below 1 Ω |
| G78-2 (LBR-) or A16-18 (BLFC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG