Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455114 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB5  Open in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1AB5 Open in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator


·

Outer mirror LH (outer rear view mirror indicator LH)

·

Outer mirror retractor LH

·

Harness or connector

·

Blind spot monitor sensor LH

·

Front multiplex network door ECU LH


Blind Spot Monitor Slave A

WIRING DIAGRAM

E329056E82
1.583,1.25 1.74,1.448 0.156,0.198 10 false 2 1.583,1.729 1.74,1.927 0.156,0.198 10 false 1 1.375,1.365 1.531,1.563 0.156,0.198 10 false + 1.375,1.823 1.531,2.021 0.156,0.198 10 false - 0.323,2.198 0.979,2.427 0.656,0.229 10 false IND2 0.323,2.344 2.042,2.74 1.719,0.396 10 false Outer Mirror LH (Outer Rear View Mirror Indicator LH) 0.479,3.385 2.813,3.781 2.333,0.396 10 false Outer Mirror Retractor LH 2.885,1.344 3.354,1.542 0.469,0.198 10 false z29 2.948,1.156 3.417,1.354 0.469,0.198 10 false 8 3.281,1.354 3.75,1.552 0.469,0.198 10 false BSL 3.135,3.396 4.646,4.042 1.51,0.646 10 false Front Multiplex Network Door ECU LH 4.031,1.375 4.5,1.573 0.469,0.198 10 false BSMI 4.094,1.833 4.563,2.031 0.469,0.198 10 false GND 4.542,1.344 5.01,1.542 0.469,0.198 10 false E25 4.583,1.146 5.052,1.344 0.469,0.198 10 false 21 4.615,1.635 5.083,1.833 0.469,0.198 10 false 1 5.969,1.375 6.438,1.573 0.469,0.198 10 false OMIL 5.781,1.25 6.25,1.448 0.469,0.198 10 false 4 5.885,3.396 6.354,3.594 0.469,0.198 10 false G60 5.885,3.552 7.115,4.177 1.229,0.625 10 false Blind Spot Monitor Sensor LH 2.917,1.625 3.188,1.792 0.271,0.167 10 false 12 3.302,1.802 3.542,1.969 0.24,0.167 10 false - 2.875,1.823 3.344,2.021 0.469,0.198 10 false z29 4.542,1.823 5.01,2.021 0.469,0.198 10 false E25

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

Result:
Result Proceed to
C1AB5 is not output A
C1AB5 is output B



A

B

2.CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)

Pre-procedure1

a.

Disconnect the G60 blind spot monitor sensor LH connector.


b.

Disconnect the E25 front multiplex network door ECU LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G60,E25)Location & Routing

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

Click Connector(E25)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU LH

G60-4 (OMIL) - E25-21 (BSMI) Always Below 1 Ω
E25-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.INSPECT FRONT MULTIPLEX NETWORK DOOR ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT MULTIPLEX NETWORK DOOR ECU LH

Pre-procedure1

a.
E364709C15
1.531,1.823 1.896,2.042 0.365,0.219 2.26,0.167 2.625,0.385 0.365,0.219 2.083,1.5 2.25,1.5 2.25,1.5 2.583,1.167 true 2.917,1.5 3.083,1.5 3.083,1.5 2.917,0.833 true 0.583,2.25 0.75,2.25 0.75,2.25 1.167,2.583 true 1.833,2.833 2.25,3.25 2.25,3.25 2.417,3.25 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 2.323,0.188 2.635,0.385 0.313,0.198 10 false E25 1.604,1.844 1.917,2.042 0.313,0.198 10 false z29 1.698,1.417 2.094,1.583 0.396,0.167 10 false BSMI 2.594,1.417 2.99,1.583 0.396,0.167 10 false GND 0.292,2.167 0.74,2.385 0.448,0.219 10 false BSL 2.49,3.156 2.885,3.323 0.396,0.167 10 false -
*a Component without harness connected
(Front Multiplex Network Door ECU LH)


Disconnect the front multiplex network door ECU LH connectors.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E25,z29)Location & Routing

Click Connector(E25)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU LH

Click Connector(z29)Body>other>Outer Rear View Mirror Assembly LH , Front Multiplex Network Door ECU LH

E25-21 (BSMI) - z29-8 (BSL) Always Below 1 Ω
E25-1 (GND) - z29-12 (-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.INSPECT OUTER MIRROR RETRACTOR LH

NG

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH

4.INSPECT OUTER MIRROR RETRACTOR LH

Pre-procedure1

a.

Disconnect the z29 outer mirror actuator assembly LH connector.


b.

Disconnect the IND2 outer mirror LH (outer rear view mirror indicator LH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z29)Location & Routing

Click Connector(z29)Body>other>Outer Rear View Mirror Assembly LH , Front Multiplex Network Door ECU LH

z29-8 (BSL) - IND 2-2 (+) Always Below 1 Ω
z29-12 (-) - IND 2-1 (-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

5.INSPECT OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

NG

REPLACE OUTER MIRROR RETRACTOR LH

5.INSPECT OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

OK

NG

REPLACE OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)