The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors is detected consecutively 3 times.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B2325 | LIN Communication Bus Malfunction | The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more. | ·
Main body ECU (multiplex network body ECU) ·
Driver side junction block assembly ·
Multiplex network master switch assembly ·
Front power window regulator motor assembly LH ·
Front power window regulator motor assembly RH ·
Front multiplex network door ECU assembly LH (w/ Reverse Shift-linked Mirror) ·
Front multiplex network door ECU assembly RH (w/ Reverse Shift-linked Mirror) ·
Rear multiplex network door ECU assembly LH ·
Rear multiplex network door ECU assembly RH ·
Harness or connector ·
Rear power window regulator motor assembly RH ·
Rear power window regulator motor assembly LH |
Main Body | A |
for LHD
for RHD
When using the GTS with the ignition switch off to troubleshoot:
Connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds until communication between the GTS and vehicle begins.
When the front power window regulator motor assembly LH is removed and reinstalled or replaced, the front power window regulator motor assembly LH must be initialized.
Pre-procedure1
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is not output | A |
| B2325 is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for LHD with Reverse Shift-linked Mirror | A |
| for LHD without Reverse Shift-linked Mirror | B |
| for RHD with Reverse Shift-linked Mirror | C |
| for RHD without Reverse Shift-linked Mirror | D |
A
B
C
D
Pre-procedure1
Disconnect the E25 front multiplex network door ECU LH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B1206 and B2321 are output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E7 front multiplex network door ECU RH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2322 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the F1 rear power window regulator motor assembly RH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2323 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E2 rear power window regulator motor assembly RH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2323 is output | B |
Post-procedure1
None
A
B
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/ Roof Sunshade System | A |
| w/o Roof Sunshade System | B |
A
B
Pre-procedure1
Disconnect the H4 sliding roof drive gear sub-assembly connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B1273 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
*1: w/ Reverse Shift-linked Mirror
*2: w/o Reverse Shift-linked Mirror
*3: w/ Roof Sunshade System
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Reconnect the driver side junction block assembly connectors.
Disconnect the E25 front multiplex network door ECU LH connector.*1
Disconnect the E7 front multiplex network door ECU RH connector.*1
Disconnect the E32 multiplex network master switch connector.*2
Disconnect the E2 front power window regulator motor assembly RH connector.*2
Disconnect the F12 rear window regulator motor assembly LH connector.
Disconnect the F1 rear window regulator motor assembly RH connector.
Disconnect the H4 sliding roof drive gear sub-assembly connector.*3
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-16 (LIN2) - Body ground | Always | 10 kΩ or higher |
| A-16 (LIN2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
*1: w/ Reverse Shift-linked Mirror
*2: w/o Reverse Shift-linked Mirror
*3: w/ Roof Sunshade System
Reconnect the driver side junction block assembly connectors.
Disconnect the E25 front multiplex network door ECU LH connector.*1
Disconnect the E7 front multiplex network door ECU RH connector.*1
Disconnect the E32 multiplex network master switch connector.*2
Disconnect the E2 front power window regulator motor assembly RH connector.*2
Disconnect the F1 rear window regulator motor assembly RH connector.
Disconnect the F12 rear window regulator motor assembly LH connector.
Disconnect the H4 sliding roof drive gear sub-assembly connector.*3
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4A-19 - Body ground | Always | 10 kΩ or higher |
| 4A-19 - Other terminals | Always | 10 kΩ or higher |
| 4A-20 - Body ground | Always | 10 kΩ or higher |
| 4A-20 - Other terminals | Always | 10 kΩ or higher |
| 4H-34 - Body ground | Always | 10 kΩ or higher |
| 4H-34 - Other terminals | Always | 10 kΩ or higher |
| 4H-35 - Body ground | Always | 10 kΩ or higher |
| 4H-35 - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the E2 front power window regulator motor assembly RH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2322 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E7 front multiplex network door ECU RH connector.
Disconnect the E2 front power window regulator motor assembly RH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E7,E2)Location & Routingewd_type=routing;type=c,c;code=E7,E2 Click Connector(E7)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU RHewd_type=component;type=c;code=E7;pinno=13 Click Connector(E2)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly RHewd_type=component;type=c;code=E2;pinno=9 |
||
| E7-13 (LIN3) - E2-9 (LIN) | Always | Below 1 Ω |
| E7-13 (LIN3) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the E32 multiplex network master switch assembly connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B1206 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E25 front multiplex network door ECU LH connector.
Disconnect the E32 multiplex network master switch assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E25,E32)Location & Routingewd_type=routing;type=c,c;code=E25,E32 Click Connector(E25)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU LHewd_type=component;type=c;code=E25;pinno=12 Click Connector(E32)Body>Front Door Wire LH / Front Door Wire RH>Multiplex Network Master Switch Assemblyewd_type=component;type=c;code=E32;pinno=17 |
||
| E25-12 (LIN2) - E32-17 (LIN1) | Always | Below 1 Ω |
| E25-12 (LIN2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the E20 front power window regulator motor assembly LH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2321 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E32 front multiplex network door ECU LH connector.
Disconnect the E20 front power window regulator motor assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E25,E20)Location & Routingewd_type=routing;type=c,c;code=E25,E20 Click Connector(E25)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU LHewd_type=component;type=c;code=E25;pinno=13 Click Connector(E20)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly LHewd_type=component;type=c;code=E20;pinno=9 |
||
| E25-13 (LIN3) - E20-9 (LIN) | Always | Below 1 Ω |
| E25-13 (LIN3) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the E32 multiplex network master switch assembly connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B1206 and B2321 are output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E2 front power window regulator motor assembly RH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2322 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E20 front power window regulator motor assembly LH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2321 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E20 front power window regulator motor assembly LH connector.
Disconnect the E32 multiplex network master switch assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E20,E32)Location & Routingewd_type=routing;type=c,c;code=E20,E32 Click Connector(E20)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly LHewd_type=component;type=c;code=E20;pinno=9 Click Connector(E32)Body>Front Door Wire LH / Front Door Wire RH>Multiplex Network Master Switch Assemblyewd_type=component;type=c;code=E32;pinno=16 |
||
| E20-9 (LIN) - E32-16 (LIN2) | Always | Below 1 Ω |
| E20-9 (LIN) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the E7 front multiplex network door ECU RH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B1206 and B2321 are output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E25 front multiplex network door ECU LH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2322 is output | B |
Post-procedure1
None
A
B
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/ Double Locking System | A |
| w/o Double Locking System | B |
A
B
Pre-procedure1
Disconnect the F5 rear multiplex network door ECU RH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2323 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the F16 rear multiplex network door ECU LH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2324 is output | B |
Post-procedure1
None
A
B
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/ Roof Sunshade System | A |
| w/o Roof Sunshade System | B |
A
B
Pre-procedure1
Disconnect the H4 sliding roof drive gear sub-assembly connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B1273 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
*1: w/ Reverse Shift-linked Mirror
*2: w/o Reverse Shift-linked Mirror
*3: w/ Roof Sunshade System
*4: w/ Double Locking System
*5: w/o Double Locking System
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Reconnect the driver side junction block assembly connectors.
Disconnect the E25 front multiplex network door ECU LH connector.*1
Disconnect the E7 front multiplex network door ECU RH connector.*1
Disconnect the E32 multiplex network master switch connector.*2
Disconnect the E2 front power window regulator motor assembly RH connector.*2
Disconnect the E25 rear multiplex network door ECU LH connector.*4
Disconnect the F5 rear multiplex network door ECU RH connector.*4
Disconnect the F12 rear window regulator motor assembly LH connector.*5
Disconnect the F1 rear window regulator motor assembly RH connector.*5
Disconnect the H4 sliding roof drive gear sub-assembly connector.*3
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-16 (LIN2) - Body ground | Always | 10 kΩ or higher |
| A-16 (LIN2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Disconnect the E32 multiplex network master switch assembly connector.
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B1206 and B2321 are output | B |
A
B
Disconnect the E7 front multiplex network door ECU RH connector.
Disconnect the E14 multiplex network master switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E7,E14)Location & Routingewd_type=routing;type=c,c;code=E7,E14 Click Connector(E7)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU RHewd_type=component;type=c;code=E7;pinno=12 Click Connector(E14)Body>Front Door Wire LH / Front Door Wire RH>Multiplex Network Master Switch Assemblyewd_type=component;type=c;code=E14;pinno=17 |
||
| E7-12 (LIN2) - E14-17 (LIN1) | Always | Below 1 Ω |
| E7-12 (LIN2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the E2 front power window regulator motor assembly RH connector.
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2321 is output | B |
A
B
Disconnect the E20 front power window regulator motor assembly LH connector.
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2322 is output | B |
A
B
Disconnect the E25 front multiplex network door ECU LH connector.
Disconnect the E20 front power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E25,E20)Location & Routingewd_type=routing;type=c,c;code=E25,E20 Click Connector(E25)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU LHewd_type=component;type=c;code=E25;pinno=13 Click Connector(E20)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly LHewd_type=component;type=c;code=E20;pinno=9 |
||
| E25-13 (LIN3) - E20-9 (LIN) | Always | Below 1 Ω |
| E25-13 (LIN3) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F1 rear power window regulator motor assembly RH connector.
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2323 is output | B |
A
B
Pre-procedure1
Disconnect the F5 rear power window regulator motor assembly RH connector.
Disconnect the F1 rear multiplex network door ECU RH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(F5,F1)Location & Routingewd_type=routing;type=c,c;code=F5,F1 Click Connector(F5)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU RHewd_type=component;type=c;code=F5;pinno=23 Click Connector(F1)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly RHewd_type=component;type=c;code=F1;pinno=9 |
||
| F5-23 (LIN3) - F1-9 (LIN) | Always | Below 1 Ω |
| F5-23 (LIN3) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the F12 rear power window regulator motor assembly LH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2324 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the F12 rear power window regulator motor assembly LH connector.
Disconnect the F16 rear multiplex network door ECU LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(F16,F12)Location & Routingewd_type=routing;type=c,c;code=F16,F12 Click Connector(F16)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU LHewd_type=component;type=c;code=F16;pinno=23 Click Connector(F12)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LHewd_type=component;type=c;code=F12;pinno=9 |
||
| F16-23 (LIN3) - F12-9 (LIN) | Always | Below 1 Ω |
| F16-23 (LIN3) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
*1: w/ Reverse Shift-linked Mirror
*2: w/o Reverse Shift-linked Mirror
*3: w/ Roof Sunshade System
*4: w/ Double Locking System
*5: w/o Double Locking System
Reconnect the driver side junction block assembly connectors.
Disconnect the E25 front multiplex network door ECU LH connector.*1
Disconnect the E7 front multiplex network door ECU RH connector.*1
Disconnect the E32 multiplex network master switch connector.*2
Disconnect the E2 front power window regulator motor assembly RH connector.*2
Disconnect the E25 rear multiplex network door ECU LH connector.*4
Disconnect the F5 rear multiplex network door ECU RH connector.*4
Disconnect the F12 rear window regulator motor assembly LH connector.*5
Disconnect the F1 rear window regulator motor assembly RH connector.*5
Disconnect the H4 sliding roof drive gear sub-assembly connector.*3
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4A-40 - Body ground | Always | 10 kΩ or higher |
| 4A-40 - Other terminals | Always | 10 kΩ or higher |
| 4H-33 - Body ground | Always | 10 kΩ or higher |
| 4H-33 - Other terminals | Always | 10 kΩ or higher |
| 4H-34 - Body ground | Always | 10 kΩ or higher |
| 4H-34 - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Disconnect the F1 rear power window regulator motor assembly RH connector.
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2323 is output | B |
A
B
Pre-procedure1
Disconnect the F12 rear power window regulator motor assembly LH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2324 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E14 multiplex network master switch assembly connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B1206 and B2321 are output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E20 front power window regulator motor assembly LH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2322 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E2 front power window regulator motor assembly RH connector.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2325 is output | A |
| B2321 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the E2 front power window regulator motor assembly RH connector.
Disconnect the E14 multiplex network master switch assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(E2,E14)Location & Routingewd_type=routing;type=c,c;code=E2,E14 Click Connector(E2)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly RHewd_type=component;type=c;code=E2;pinno=9 Click Connector(E14)Body>Front Door Wire LH / Front Door Wire RH>Multiplex Network Master Switch Assemblyewd_type=component;type=c;code=E14;pinno=16 |
||
| E2-9 (LIN) - E14-16 (LIN2) | Always | Below 1 Ω |
| E2-9 (LIN) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG