Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U011000  Lost Communication with Drive Motor Control Module "A"  U011087  Lost Communication with Drive Motor Control Module "A" Missing Message  U012987  Lost Communication with Brake System Control Module Missing Message  U115000  Lost Communication with Hybrid Powertrain Control Module (ch2)  U115087  Lost Communication with Hybrid Powertrain Control Module (ch2) Missing Message  U115987  Lost Communication with Electronic Brake Booster Control Module "A" (ch3) Missing Message  U117D87  Lost Communication with Brake System Control Module (ch4) Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U011000 Lost Communication with Drive Motor Control Module "A" Communication stop occurs between the EV control ECU assembly and ECU or sensor outputs DTC(s)
·

CAN main/branch bus lines or connector

·

EV control ECU assembly

·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

No. 1 CAN junction connector


Brake Booster A
U011087 Lost Communication with Drive Motor Control Module "A" Missing Message Communication stop occurs between the EV control ECU assembly and ECU or sensor outputs DTC(s)
·

CAN main/branch bus lines or connector

·

EV control ECU assembly

·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

No. 1 CAN junction connector


Brake/EPB A
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and ECU or sensor outputs DTC(s)
·

CAN main/branch bus lines or connector

·

EV control ECU assembly

·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

No. 1 CAN junction connector


EV A
U115000 Lost Communication with Hybrid Powertrain Control Module (ch2) Communication stop occurs between the EV control ECU assembly and ECU or sensor outputs DTC(s)
·

CAN main/branch bus lines or connector

·

EV control ECU assembly

·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

No. 1 CAN junction connector


Brake Booster A
U115087 Lost Communication with Hybrid Powertrain Control Module (ch2) Missing Message Communication stop occurs between the EV control ECU assembly and ECU or sensor outputs DTC(s)
·

CAN main/branch bus lines or connector

·

EV control ECU assembly

·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

No. 1 CAN junction connector


Brake/EPB A
U115987 Lost Communication with Electronic Brake Booster Control Module "A" (ch3) Missing Message Communication stop occurs between the brake booster with master cylinder assembly (No. 1 skid control ECU) and ECU or sensor outputs DTC(s)
·

CAN main/branch bus lines or connector

·

EV control ECU assembly

·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

No. 1 CAN junction connector


Brake/EPB A
U117D87 Lost Communication with Brake System Control Module (ch4) Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and ECU or sensor outputs DTC(s)
·

CAN main/branch bus lines or connector

·

EV control ECU assembly

·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

No. 1 CAN junction connector


Brake Booster A

WIRING DIAGRAM

C452761E02
5.833,1.688 6.927,1.885 1.094,0.198 10 false EV Control ECU 0.094,1.563 1.76,2.083 1.667,0.521 10 false Brake Booster with Master Cylinder Assembly (No. 1 Skid Control ECU) 5.521,3.542 7.104,3.938 1.583,0.396 10 false Brake Actuator Assembly (No. 2 Skid Control ECU) 2.813,3.594 4.698,3.833 1.885,0.24 10 false No. 1 CAN Junction Connector 5.833,1.521 6.76,1.698 0.927,0.177 10 false A8*1, D15*2 5.99,0.573 6.49,0.792 0.5,0.219 10 false CA3P 6.01,1.24 6.51,1.458 0.5,0.219 10 false CA3N 6.042,2.594 6.542,2.813 0.5,0.219 10 false CA2H 5.698,0.594 6,0.833 0.302,0.24 10 false 14 5.698,1.01 6,1.25 0.302,0.24 10 false 15 6.042,3.26 6.542,3.479 0.5,0.219 10 false CA2L 5.708,2.615 6.01,2.854 0.302,0.24 10 false 16 5.698,3.021 6,3.26 0.302,0.24 10 false 17 0.917,0.698 1.375,0.885 0.458,0.188 10 false CA2H 0.917,1.115 1.333,1.313 0.417,0.198 10 false CA2L 1.396,1 1.698,1.24 0.302,0.24 10 false 36 1.396,0.604 1.698,0.844 0.302,0.24 10 false 35 2.802,3.427 3.302,3.646 0.5,0.219 10 false A78 5.531,3.375 6.031,3.594 0.5,0.219 10 false A6 0.104,1.396 0.604,1.615 0.5,0.219 10 false A5 3.156,0.979 3.458,1.219 0.302,0.24 10 false 17 3.208,0.573 3.51,0.813 0.302,0.24 10 false 6 4.042,1.021 4.344,1.26 0.302,0.24 10 false 16 4.063,0.604 4.365,0.844 0.302,0.24 10 false 5 4.031,3.031 4.333,3.271 0.302,0.24 10 false 13 4.063,2.604 4.365,2.844 0.302,0.24 10 false 2 0.24,3.833 1.927,4.031 1.688,0.198 10 false *1: for LHD 0.24,4.229 1.927,4.427 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Chassis > Brake/EPB > Trouble Codes
50001 435
Chassis > Brake Booster > Trouble Codes
50001 466
Display on GTS / Output DTC Pattern
Pattern 1 Pattern 2 Pattern 3

○: DTC is output

-: DTC is not output

Brake Booster U011000 ○ - ○
U115000 ○ - ○
U117D87 ○ ○ -
Brake/EPB U011087 - ○ ○
U115087 - ○ ○
U115987 ○ ○ -
EV U012987 - ○ ○


Result:
Result Proceed to
Pattern 1 A
Pattern 2 B
Pattern 3 C
Other Pattern D



A

2.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU) - NO. 1 CAN JUNCTION CONNECTOR)

B

3.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU) - NO. 1 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR OPEN IN CAN BUS WIRE (EV CONTROL ECU - NO. 1 CAN JUNCTION CONNECTOR)

D

5.CHECK FOR OPEN IN CAN BUS WIRE
2.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE BOOSTER ASSEMBLY WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU) - NO. 1 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A5 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A5)Location & Routing

Click Connector(A5)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Booster with Master Cylinder Assembly

A5-35 (CA2H) - A5-36 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU) - NO. 1 CAN JUNCTION CONNECTOR)

3.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU) - NO. 1 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-16 (CA2H) - A6-17 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU) - NO. 1 CAN JUNCTION CONNECTOR)

4.CHECK FOR OPEN IN CAN BUS WIRE (EV CONTROL ECU - NO. 1 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD



Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-14 (CA3P) - A8-15 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D15-14 (CA3P) - D15-15 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (EV CONTROL ECU - NO. 10 CAN JUNCTION CONNECTOR)

5.CHECK FOR OPEN IN CAN BUS WIRE

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

A484770C02
6.083,0.438 6.5,0.719 0.417,0.281 6.083,0.104 6.5,0.385 0.417,0.281 5.448,2.188 5.625,2.188 5.625,2.188 6.01,1.406 true 5.615,2.479 5.792,2.479 5.792,2.479 6.125,1.406 true 6.177,0.49 6.635,0.688 0.458,0.198 10 false D15 5.042,2.094 5.656,2.292 0.615,0.198 10 false CA3N 5.229,2.396 5.844,2.594 0.615,0.198 10 false CA3P 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 6.208,0.167 6.49,0.344 0.281,0.177 10 false A8 6.552,0.156 6.813,0.333 0.26,0.177 10 false *A 6.552,0.479 6.813,0.656 0.26,0.177 10 false *B
*A for LHD *B for RHD
*a Component with harness connected
(to EV Control ECU)
- -


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-14 (CA3P) - A8-15 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D15-14 (CA3P) - D15-15 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

6.CHECK FOR SHORT IN CAN BUS WIRES

NG

27.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)
6.CHECK FOR SHORT IN CAN BUS WIRES
a.

Measure the resistance according to the value(s) in the table below.

A484770C02
6.083,0.438 6.5,0.719 0.417,0.281 6.083,0.104 6.5,0.385 0.417,0.281 5.448,2.188 5.625,2.188 5.625,2.188 6.01,1.406 true 5.615,2.479 5.792,2.479 5.792,2.479 6.125,1.406 true 6.177,0.49 6.635,0.688 0.458,0.198 10 false D15 5.042,2.094 5.656,2.292 0.615,0.198 10 false CA3N 5.229,2.396 5.844,2.594 0.615,0.198 10 false CA3P 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 6.208,0.167 6.49,0.344 0.281,0.177 10 false A8 6.552,0.156 6.813,0.333 0.26,0.177 10 false *A 6.552,0.479 6.813,0.656 0.26,0.177 10 false *B
*A for LHD *B for RHD
*a Component with harness connected
(to EV Control ECU)
- -


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-24 (CA3P) - A8-11 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D15-14 (CA3P) - D15-15 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher



Result:
Proceed to
OK
NG



OK

7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE

NG

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)
7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE
a.

Measure the resistance according to the value(s) in the table below.

C441474C01
6,0.667 6.417,0.917 0.417,0.25 4.365,0.25 4.781,0.5 0.417,0.25 4.365,0.667 4.781,0.917 0.417,0.25 3.813,2.229 3.99,2.229 3.99,2.229 4.375,1.448 true 3.948,2.552 4.125,2.552 4.125,2.552 4.458,1.479 true 6.313,2.052 6.49,2.052 6.49,2.052 6.635,1.625 true 4.458,0.708 4.917,0.906 0.458,0.198 10 false D15 3.375,2.146 3.99,2.344 0.615,0.198 10 false CA3N 3.51,2.469 4.125,2.667 0.615,0.198 10 false CA3P 0.135,0.708 0.448,0.906 0.313,0.198 10 false *a 4.479,0.292 4.76,0.469 0.281,0.177 10 false A8 4.854,0.292 5.115,0.469 0.26,0.177 10 false *A 4.833,0.729 5.094,0.906 0.26,0.177 10 false *B 5.5,0.75 5.813,0.948 0.313,0.198 10 false *b 6.073,0.708 6.531,0.906 0.458,0.198 10 false D20 6,1.979 6.615,2.177 0.615,0.198 10 false BAT
*A for LHD *B for RHD
*a Component with harness connected
(to EV Control ECU)
*b Front view of DLC3


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(A8,D20)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A8-14 (CA3P) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A8-15 (CA3N) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(D15,D20)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D15-14 (CA3P) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D15-15 (CA3N) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE

NG

15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE
a.

Measure the resistance according to the value(s) in the table below.

C441474C03
6,0.667 6.417,0.917 0.417,0.25 4.365,0.25 4.781,0.5 0.417,0.25 4.365,0.667 4.781,0.917 0.417,0.25 3.813,2.229 3.99,2.229 3.99,2.229 4.375,1.448 true 3.948,2.552 4.125,2.552 4.125,2.552 4.458,1.479 true 6.156,1.26 6.583,0.917 6.583,0.917 6.75,0.917 true 4.458,0.708 4.917,0.906 0.458,0.198 10 false D15 3.375,2.146 3.99,2.344 0.615,0.198 10 false CA3N 3.51,2.469 4.125,2.667 0.615,0.198 10 false CA3P 0.135,0.708 0.448,0.906 0.313,0.198 10 false *a 4.479,0.292 4.76,0.469 0.281,0.177 10 false A8 4.854,0.292 5.115,0.469 0.26,0.177 10 false *A 4.833,0.729 5.094,0.906 0.26,0.177 10 false *B 5.5,0.75 5.813,0.948 0.313,0.198 10 false *b 6.073,0.708 6.531,0.906 0.458,0.198 10 false D20 6.813,0.844 7.156,1.073 0.344,0.229 10 false CG
*A for LHD *B for RHD
*a Component with harness connected
(to EV Control ECU)
*b Front view of DLC3


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(A8,D20)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A8-14(CA3P) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A8-15(CA3N) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(D15,D20)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D15-14 (CA3P) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D15-15 (CA3N) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

CHECK INTERMITTENT PROBLEMS

NG

9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)
9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the A78 No. 1 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-5 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A78-16 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)
10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A78-13 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

NG

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-6 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A78-17 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-5 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A78-16 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

Pre-procedure1

a.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A78-13 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

Pre-procedure1

a.

Disconnect the A5 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-6 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A78-17 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the A78 No. 1 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-5 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A78-16 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)
16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A78-13 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

NG

19.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
17.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-6 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A78-17 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-5 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A78-16 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)

19.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

Pre-procedure1

a.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A78-13 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

Pre-procedure1

a.

Disconnect the A5 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78,D20)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

A78-6 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A78-17 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the A78 No. 1 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

A78-5 (CANH) - A78-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)
22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

A78-2 (CANH) - A78-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

NG

25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

A78-6 (CANH) - A78-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

A78-5 (CANH) - A78-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)

25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

Pre-procedure1

a.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

A78-2 (CANH) - A78-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

Pre-procedure1

a.

Disconnect the A5 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

A78-6 (CANH) - A78-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

27.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the A78 No. 1 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

A78-5 (CANH) - A78-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

28.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

29.CHECK FOR OPEN IN CAN BUS WIRE (EV CONTROL ECU - NO. 1 CAN JUNCTION CONNECTOR)
28.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A78)Location & Routing

Click Connector(A78)Instrument Panel>Front Compartment Main Wire>No. 1 CAN Junction Connector

A78-2 (CANH) - A78-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

30.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU) - NO. 1 CAN JUNCTION CONNECTOR)
29.CHECK FOR OPEN IN CAN BUS WIRE (EV CONTROL ECU - NO. 1 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the A78 No. 1 CAN junction connector.


b.

Disconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD



Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-14 (CA3P) - A8-15 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D15-14 (CA3P) - D15-15 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (EV CONTROL ECU - NO. 1 CAN JUNCTION CONNECTOR)

30.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU) - NO. 1 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the A78 No. 1 CAN junction connector.


b.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-16 (CA2H) - A6-17 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU) - NO. 1 CAN JUNCTION CONNECTOR)