Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U012587  Lost Communication with Multi-axis Acceleration Sensor Module Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the EV control ECU assembly and ECU or sensor outputs DTC(s)
·

CAN main/branch bus lines or connector

·

Airbag ECU assembly

·

Brake actuator assembly (No. 2 skid control ECU)

·

Rack and pinion power steering gear assembly

·

Central gateway ECU (network gateway ECU)

·

No. 3 CAN junction connector


Brake/EPB A

WIRING DIAGRAM

C441459E02
5.156,1.521 7.104,1.927 1.948,0.406 10 false Central Gateway ECU (Network Gateway ECU) 0.135,1.542 2.083,1.948 1.948,0.406 10 false Airbag ECU Assembly 5.594,3.542 7.052,4.083 1.458,0.542 10 false Brake Actuator Bracket Assembly (No. 2 Skid Control ECU) 2.813,3.594 4.698,3.833 1.885,0.24 10 false No. 3 CAN Junction Connector 5.167,1.365 5.667,1.583 0.5,0.219 10 false D119 6.094,0.594 6.594,0.813 0.5,0.219 10 false CAWH 6.083,1.271 6.583,1.49 0.5,0.219 10 false CAWL 6.042,2.594 6.542,2.813 0.5,0.219 10 false CA3H 5.698,0.594 6,0.833 0.302,0.24 10 false 13 5.688,1.01 5.99,1.25 0.302,0.24 10 false 12 6.042,3.26 6.542,3.479 0.5,0.219 10 false CA3L 5.708,2.615 6.01,2.854 0.302,0.24 10 false 28 5.708,3.031 6.01,3.271 0.302,0.24 10 false 44 0.875,0.698 1.375,0.917 0.5,0.219 10 false CANH 0.917,1.115 1.417,1.333 0.5,0.219 10 false CANL 1.375,1.021 1.677,1.26 0.302,0.24 10 false 19 1.396,0.604 1.698,0.844 0.302,0.24 10 false 20 2.802,3.427 3.302,3.646 0.5,0.219 10 false D168 5.594,3.375 6.094,3.594 0.5,0.219 10 false A6 0.104,1.396 0.604,1.615 0.5,0.219 10 false D10 2.667,1.01 3.49,1.25 0.823,0.24 10 false 13*1, 14*2 2.813,0.583 3.552,0.854 0.74,0.271 10 false 4*1, 3*2 4.042,1.021 4.344,1.26 0.302,0.24 10 false 12 4.063,0.604 4.365,0.844 0.302,0.24 10 false 1 4.031,3.031 4.823,3.229 0.792,0.198 10 false 14*1, 13*2 4.063,2.604 4.802,2.813 0.74,0.208 10 false 3*1, 2*2 0.208,3.531 0.708,3.75 0.5,0.219 10 false A80 0.188,3.698 2.177,4.146 1.99,0.448 10 false Rack and Pinion Power Steering Gear Assembly*1 0.177,4.5 1.115,4.813 0.938,0.313 10 false *1: for LHD 1.396,2.615 1.698,2.854 0.302,0.24 10 false 10 1.406,3.021 1.708,3.26 0.302,0.24 10 false 11 0.875,2.698 1.375,2.917 0.5,0.219 10 false CA2H 0.896,3.115 1.396,3.333 0.5,0.219 10 false CA2L 1.083,4.5 2.021,4.813 0.938,0.313 10 false *2: for RHD 3.063,2.604 3.563,2.833 0.5,0.229 10 false 2*1 3.01,3.042 3.51,3.271 0.5,0.229 10 false 13*1

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Procedure1

b.
C425195C95
1.51,0.073 1.927,0.323 0.417,0.25 0.365,1.813 1.052,0.771 true 2.583,1.823 1.156,0.771 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.573,0.115 2.031,0.313 0.458,0.198 10 false D119 0.188,1.865 0.656,2.083 0.469,0.219 10 false CAWH 2.51,1.865 3.073,2.115 0.563,0.25 10 false CAWL
*a Component with harness connected
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D119)Location & Routing

Click Connector(D119)Instrument Panel>Instrument Panel Wire>Network Gateway ECU

D119-13 (CAWH) - D119-12 (CAWL) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

2.CHECK FOR SHORT IN CAN BUS WIRES

NG

44.CHECK VEHICLE TYPE
2.CHECK FOR SHORT IN CAN BUS WIRES
a.
C425195C95
1.51,0.073 1.927,0.323 0.417,0.25 0.365,1.813 1.052,0.771 true 2.583,1.823 1.156,0.771 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.573,0.115 2.031,0.313 0.458,0.198 10 false D119 0.188,1.865 0.656,2.083 0.469,0.219 10 false CAWH 2.51,1.865 3.073,2.115 0.563,0.25 10 false CAWL
*a Component with harness connected
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D119)Location & Routing

Click Connector(D119)Instrument Panel>Instrument Panel Wire>Network Gateway ECU

D119-13 (CAWH) - D119-12 (CAWL) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher



Result:
Proceed to
OK
NG



OK

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE

NG

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE
a.
C421610C40
1.5,0.083 1.917,0.333 0.417,0.25 1.5,2.583 1.917,2.833 0.417,0.25 0.667,1.833 0.833,1.833 0.833,1.833 1.052,0.76 true 2.479,1.885 2.313,1.885 2.313,1.885 1.146,0.781 true 2.844,4.25 2.677,4.25 2.677,4.25 2.354,3.76 true 1.552,0.115 2.167,0.313 0.615,0.198 10 false D119 1.583,2.625 2.198,2.823 0.615,0.198 10 false D20 0.188,1.76 0.802,1.958 0.615,0.198 10 false CAWH 2.573,1.823 3.188,2.021 0.615,0.198 10 false CAWL 2.906,4.177 3.406,4.396 0.5,0.219 10 false BAT 0.083,0.094 0.698,0.292 0.615,0.198 10 false *a 0.167,2.646 0.781,2.844 0.615,0.198 10 false *b
*a Component with harness connected
(to Central Gateway ECU (Network Gateway ECU))
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D119,D20)Location & Routing

Click Connector(D119)Instrument Panel>Instrument Panel Wire>Network Gateway ECU

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D119-13 (CAWH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D119-12 (CAWL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE

NG

18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE
a.
C421610C40
1.5,0.083 1.917,0.333 0.417,0.25 1.5,2.583 1.917,2.833 0.417,0.25 0.667,1.833 0.833,1.833 0.833,1.833 1.052,0.76 true 2.479,1.885 2.313,1.885 2.313,1.885 1.146,0.781 true 2.844,4.25 2.677,4.25 2.677,4.25 2.354,3.76 true 1.552,0.115 2.167,0.313 0.615,0.198 10 false D119 1.583,2.625 2.198,2.823 0.615,0.198 10 false D20 0.188,1.76 0.802,1.958 0.615,0.198 10 false CAWH 2.573,1.823 3.188,2.021 0.615,0.198 10 false CAWL 2.906,4.177 3.406,4.396 0.5,0.219 10 false BAT 0.083,0.094 0.698,0.292 0.615,0.198 10 false *a 0.167,2.646 0.781,2.844 0.615,0.198 10 false *b
*a Component with harness connected
(to Central Gateway ECU (Network Gateway ECU))
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D119,D20)Location & Routing

Click Connector(D119)Instrument Panel>Instrument Panel Wire>Network Gateway ECU

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D119-13 (CAWH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-12 (CAWL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

CHECK INTERMITTENT PROBLEMS

NG

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

Pre-procedure1

a.

Disconnect the No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-1 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-12 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

6.CHECK VEHICLE TYPE

NG

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
6.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

B

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-13 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-3 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-14 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

NG

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-4 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-15 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the D120 central gateway ECU (network gateway ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-1 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-12 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the A80 airbag ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-13 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-3 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-14 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the D10 airbag ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-4 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-15 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-13 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

NG

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-3 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-14 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-13 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the D10 airbag ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-3 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D168-14 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

Pre-procedure1

a.

Disconnect the No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-1 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-12 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

19.CHECK VEHICLE TYPE

NG

23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
19.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

B

27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-13 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-3 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-14 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

NG

25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-4 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-15 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the D120 central gateway ECU (network gateway ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-1 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-12 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the A80 airbag ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-13 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-3 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-14 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the D10 airbag ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-4 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-15 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-13 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

NG

29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-3 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-14 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-13 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the D10 airbag ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168,D20)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

D168-3 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D168-14 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

Pre-procedure1

a.

Disconnect the No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-1 (CANH) - D168-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

32.CHECK VEHICLE TYPE

NG

36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
32.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

B

40.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-2 (CANH) - D168-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-3 (CANH) - D168-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

35.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

NG

38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
35.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-4 (CANH) - D168-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the D120 central gateway ECU (network gateway ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-1 (CANH) - D168-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the A80 airbag ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-2 (CANH) - D168-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - RACK AND PINION POWER STEERING GEAR ASSEMBLY)

38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-3 (CANH) - D168-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the D10 airbag ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-4 (CANH) - D168-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

40.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-2 (CANH) - D168-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

NG

42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-3 (CANH) - D168-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)
42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-2 (CANH) - D168-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the D10 airbag ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-3 (CANH) - D168-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - AIRBAG ECU ASSEMBLY)

44.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

45.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

B

48.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
45.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

Pre-procedure1

a.

Disconnect the No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-3 (CANH) - D168-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

46.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

NG

47.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU) - NO. 3 CAN JUNCTION CONNECTOR)
46.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the D120 central gateway ECU (network gateway ECU) connector.


c.

Disconnect the D10 airbag ECU assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D10)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

D10-20 (CANH) - D10-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (AIRBAG ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

47.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU) - NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-28 (CA3H) - A6-44 (CA3L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

48.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

Pre-procedure1

a.

Disconnect the No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D168)Location & Routing

Click Connector(D168)Instrument Panel>Instrument Panel Wire>No. 3 CAN Junction Connector

D168-2 (CANH) - D168-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

49.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

NG

50.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU) - NO. 3 CAN JUNCTION CONNECTOR)
49.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the D120 central gateway ECU (network gateway ECU) connector.


c.

Disconnect the D10 airbag ECU assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D10)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

D10-20 (CANH) - D10-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (AIRBAG ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

50.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU) - NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the No. 3 CAN junction connector.


b.

Disconnect the A6 brake actuator assembly (No. 2 skid control ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-28 (CA3H) - A6-44 (CA3L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))