Home › Suspension › REAR SUSPENSION › REAR STABILIZER BAR
RM37H0E _53 Suspension _097406 REAR SUSPENSION _0455877 REAR STABILIZER BAR A

REAR SUSPENSION  REAR STABILIZER BAR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C455734N01
3,0.417 3.417,0.417 true 5.104,1.792 5.406,1.792 true 2.667,1.667 3.083,1.667 true 2.75,1.917 3.167,1.917 true 0.917,1.25 1.333,1.25 true 0.75,1 1.167,1 true 2.083,3.031 2.292,3.031 2.292,3.031 2.667,2.281 true 1.875,5.188 2.083,5.188 2.083,5.188 2.458,4.438 true 2.594,1.365 2.906,1.563 0.313,0.198 10 false x 2 1.177,0.313 1.49,0.51 0.313,0.198 10 false x 2 1.615,5.031 1.896,5.385 0.281,0.354 18 false 1 3.115,1.49 3.396,1.844 0.281,0.354 18 false 5 3.479,0.281 3.76,0.635 0.281,0.354 18 false 3 1.802,2.875 2.083,3.229 0.281,0.354 18 false 4 0.427,0.813 0.708,1.167 0.281,0.354 18 false 6 3.219,1.792 3.5,2.146 0.281,0.354 18 false 7 0.625,1.125 0.906,1.479 0.281,0.354 18 false 7 5.729,1.667 6.01,2.021 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR SUSPENSION MEMBER SUB-ASSEMBLY 51206A - - -
2 REAR STABILIZER LINK ASSEMBLY LH 48840A (Click here) - -
3 REAR STABILIZER LINK ASSEMBLY RH 48830D - - -
4 REAR STABILIZER BAR 48812 - - -
5 REAR NO.1 STABILIZER BAR BRACKET LH 48833R - - -
6 REAR NO.1 STABILIZER BAR BRACKET RH 48832R - - -
7 REAR STABILIZER BUSHING 48818 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear stabilizer bar removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link

*: The vehicle height changes because of suspension or tire replacement.

·

Rear disc (Including removal and installation)

·

Parking brake shoe (Including removal and installation)

·

Parking brake actuator assembly with bracket (Removed and installed)


Parking brake bedding Electric parking brake system (Click here)
Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)
Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. Have been performed Perform headlight ECU sub-assembly LH initialization
·

Automatic headlight beam level control system

·

Adaptive highe beam system


(Click here)
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 51206A 1.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

Hide 48840A 2.REMOVE REAR STABILIZER LINK ASSEMBLY LH

Z101186

Click here(Click here)

Hide 48830D 3.REMOVE REAR STABILIZER LINK ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 48812 4.REMOVE REAR STABILIZER BAR

a.
C447192


Hide 48833R 5.REMOVE REAR NO.1 STABILIZER BAR BRACKET LH

a.
C447227


Hide 48832R 6.REMOVE REAR NO.1 STABILIZER BAR BRACKET RH

a.

Perform the same procedure as for the rear No. 1 stabilizer bar bracket LH.


Hide 48818 7.REMOVE REAR STABILIZER BUSHING

a.
C447226