Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER
RM37H0E _53 Suspension _097406 REAR SUSPENSION _0455878 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS(REMOVAL)
A479058N17
1.479,0.802 2.146,0.802 true 6.26,0.156 6.927,0.156 true 5.969,0.01 6.24,0.333 0.271,0.323 18 false 1 1.188,0.615 1.469,0.969 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 RELEASE PARKING BRAKE - (Click here) - -
2 REMOVE SERVICE PLUG GRIP G3834 (Click here) - -

A480783N14
5.917,2.167 6.917,2.333 1,0.167 4.417,1.875 5.167,1.875 false 2.573,0.854 3.323,0.854 false 3.948,4.854 3.042,3.615 3.042,3.615 2.792,3.615 true 5.719,3.083 6.01,3.083 false 6.406,0.354 6.698,0.354 false 5.417,2.667 5.417,2.25 5.417,2.25 5.917,2.25 false 5.698,2.583 5.698,2.25 false 2.594,3.51 3.156,3.802 0.563,0.292 18 false 5 5.229,1.74 5.583,2.073 0.354,0.333 18 false 3 3.448,0.708 4.073,1.052 0.625,0.344 18 false 4 4.406,1.354 4.74,1.615 0.333,0.26 10 false x 6 6.177,0.229 6.458,0.583 0.281,0.354 18 false 7 6.344,2.948 6.875,3.333 0.531,0.385 18 false 6, 8 4.604,3.417 4.927,3.625 0.323,0.208 10 false x 2 5.969,2.177 7.042,2.5 1.073,0.323 8 false 8.0 (82, 71 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

3 UPPER RADIATOR SUPPORT SEAL 53292A - - -
4 FC STACK COVER SUB-ASSEMBLY 1A906 - - -
5 FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY) G9200A (Click here) - -
6 REMOVE CONNECTOR COVER ASSEMBLY - (Click here) - -
7 CHECK TERMINAL VOLTAGE - (Click here) - -
8 INSTALL CONNECTOR COVER ASSEMBLY - (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

C449961N04
5.76,0.75 6.177,0.75 true 0.698,1.885 0.698,2.052 0.698,2.052 1.031,2.052 true 2.708,3.25 2.708,3.417 2.708,3.417 3.25,3.417 true 4.625,2.75 5.042,2.75 true 1.865,2.552 1.865,2.719 1.865,2.719 2.198,2.719 true 3.125,1.917 3.542,1.917 true 6.542,0.229 6.771,0.229 true 4.26,2.615 4.688,2.969 0.427,0.354 18 false 13 6.208,0.115 6.594,0.49 0.385,0.375 18 false 14 1.083,1.958 1.271,2.167 0.188,0.208 10 false ● 2.26,2.625 2.448,2.833 0.188,0.208 10 false ● 3.969,1.781 4.438,2.135 0.469,0.354 18 false 10 1.219,1.917 1.688,2.292 0.469,0.375 18 false 11 2.385,2.542 2.854,2.885 0.469,0.344 18 false 11 3.583,3.281 4.042,3.667 0.458,0.385 18 false 12 6.24,0.594 6.573,0.958 0.333,0.365 18 false 9

Procedure Part Name Code
Z101186

Z101188

Z101187

9 INNER LUGGAGE COMPARTMENT TRIM COVER LH 64722 - - -
10 REAR SEAT CUSHION ASSEMBLY LH - (Click here) - -
11 REAR SEAT CUSHION LOCK HOOK 72693 - - -
12 WIRE HARNESS - - - -
13 REAR TIRE - - - -
14 FORCED RELEASE PARKING BRAKE - - - (Click here)

● Non-reusable part - -

C442776N10
4.917,1.167 5.25,0.833 5.25,0.833 5.5,0.833 false 6.073,2.177 6.323,1.76 6.323,1.76 6.573,1.76 false 3.823,0.427 4.073,0.177 4.073,0.177 4.323,0.177 false 2.583,2.167 2.917,1.833 2.917,1.833 3.167,1.833 false 3.688,2.917 3.917,2.667 3.917,2.667 4.167,2.667 false 1.167,1.25 1.5,0.917 1.5,0.917 1.75,0.917 false 5.583,0.688 5.979,1.021 0.396,0.333 18 false 15 6.615,1.625 7.01,1.948 0.396,0.323 18 false 16 4.365,0.052 4.76,0.375 0.396,0.323 18 false 17 1.813,0.771 2.188,1.094 0.375,0.323 18 false 18 4.208,2.542 4.583,2.854 0.375,0.313 18 false 19 3.219,1.688 3.552,2.01 0.333,0.323 18 false 20 2.385,2.896 2.708,3.156 0.323,0.26 10 false x 2 3.156,3.5 3.49,3.688 0.333,0.188 10 false x 2 1.052,2.063 1.406,2.292 0.354,0.229 10 false x 2 2.865,2.573 3.167,2.792 0.302,0.219 10 false x 4 6.479,2.969 6.833,3.208 0.354,0.24 10 false x 4 3.458,1.021 3.708,1.188 0.25,0.167 10 false x 4 5.521,1.979 5.833,2.188 0.313,0.208 10 false x 4 4.802,2.146 5.135,2.375 0.333,0.229 10 false x 2 4.333,2.167 4.646,2.406 0.313,0.24 10 false x 6

Procedure Part Name Code
Z101186

Z101188

Z101187

15 NO. 1 FLOOR UNDER COVER 58398F - - -
16 TRANSMISSION OIL COOLER UNDER COVER LH 32912B - - -
17 TRANSMISSION OIL COOLER UNDER COVER RH 32911 - - -
18 NO. 1 DIFFERENTIAL SUPPORT PROTECTOR 52383E - - -
19 NO. 2 DIFFERENTIAL SUPPORT PROTECTOR 52384C - - -
20 REAR SUSPENSION BRACE COVER 53661B - - -

C449958N03
3.417,0.583 3.833,0.583 true 5.667,0.667 5.667,0.25 5.667,0.25 5.833,0.25 true 2.5,2.5 2.917,2.5 true 3.271,1.021 3.583,1.219 0.313,0.198 10 false x 2 4.896,2.135 5.208,2.333 0.313,0.198 10 false x 2 5.479,1.792 5.792,1.99 0.313,0.198 10 false x 3 6.198,2.573 6.51,2.771 0.313,0.198 10 false x 2 6.719,1.927 7.031,2.125 0.313,0.198 10 false x 11 2.792,3.344 3.104,3.542 0.313,0.198 10 false x 2 5.885,0.073 6.302,0.438 0.417,0.365 18 false 22 2.042,2.313 2.458,2.677 0.417,0.365 18 false 21 3.885,0.417 4.302,0.781 0.417,0.365 18 false 23

Procedure Part Name Code
Z101186

Z101188

Z101187

21 ROCKER PANEL MOULDING PROTECTOR LH 75866E - - -
22 REAR WHEEL HOUSE LINER LH 65638 - - -
23 PARKING BRAKE WITH BRACKET ACTUATOR ASSEMBLY 46300 - - -

C447223N05
2.302,3 2.875,3 true 3.708,0.271 3.969,0.271 true 3.729,0.854 4.01,0.854 true 1.167,1.844 1.521,1.844 true 0.969,0.667 1.396,0.667 true 1.917,1.708 2.271,2.021 0.354,0.313 18 false 24 1.99,2.875 2.406,3.219 0.417,0.344 18 false 25 0.646,0.542 1.031,0.885 0.385,0.344 18 false 26 4.729,0.115 5.146,0.438 0.417,0.323 18 false 27 4.5,0.719 4.906,1.021 0.406,0.302 18 false 28 0.625,2.125 0.938,2.323 0.313,0.198 10 false x 2 1.531,1.156 1.844,1.354 0.313,0.198 10 false x 2 3.646,1.135 3.958,1.333 0.313,0.198 10 false x 3 3.771,4.094 4.083,4.292 0.313,0.198 10 false x 2 4.49,0.156 4.677,0.354 0.188,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

24 MOTOR CABLE BRACKET G1143 (Click here) - -
25 MOTOR CABLE G1148 (Click here) - -
26 CONNECTOR COVER 82821T (Click here) - -
27 MOTOR CABLE TERMINAL CAP G114D (Click here) - -
28 WIRING HARNESS CONNECTOR 82H24 (Click here) - -

● Non-reusable part - -

C447198N04
5.875,2.531 5.875,2.031 5.875,2.031 6.042,2.031 true 1.26,2.448 1.26,1.948 1.26,1.948 1.427,1.948 true 0.646,1.021 0.646,1.438 0.646,1.438 0.792,1.438 true 5.24,0.542 5.573,0.917 5.573,0.917 5.74,0.917 true 4.771,2.208 4.771,1.823 4.771,1.823 4.938,1.823 true 5.208,3.396 5.208,2.896 5.208,2.896 5.375,2.896 true 0.719,3.219 0.719,3.073 0.719,3.073 0.885,3.073 true 3.698,3.052 3.938,3.052 true 5.604,4.156 5.844,4.156 true 6.667,4.76 6.667,4.042 6.667,4.042 6.771,4.042 true 0.458,5.063 0.458,4.771 0.458,4.771 0.625,4.771 true 0.979,4.344 0.979,4.052 0.979,4.052 1.146,4.052 true 1.958,5.042 1.958,5.542 1.958,5.542 2.125,5.542 true 2.385,3.104 2.396,2.708 2.396,2.708 2.521,2.708 true 2.135,2.031 2.135,1.375 2.135,1.375 2.25,1.375 true 6.531,0.271 6.771,0.271 true 2.656,1.219 3.208,1.573 0.552,0.354 18 false 30 1.177,1.26 1.729,1.615 0.552,0.354 18 false 30 6.104,1.865 6.656,2.219 0.552,0.354 18 false 31 1.51,1.792 2.063,2.146 0.552,0.354 18 false 32 6.167,0.125 6.521,0.479 0.354,0.354 18 false 29 2.906,2.552 3.458,2.906 0.552,0.354 18 false 34 2.188,5.375 2.74,5.729 0.552,0.354 18 false 35 0.979,2.917 1.531,3.271 0.552,0.354 18 false 35 5.917,4 6.469,4.354 0.552,0.354 18 false 36 1.219,3.917 1.771,4.271 0.552,0.354 18 false 37 4.021,2.896 4.573,3.25 0.552,0.354 18 false 36 4.99,1.646 5.542,2 0.552,0.354 18 false 38 6.833,3.948 7.156,4.146 0.323,0.198 10 false *1 5.438,2.813 5.792,3.031 0.354,0.219 10 false *2 6.167,0.76 6.719,1.115 0.552,0.354 18 false 39 0.688,4.604 1.042,4.958 0.354,0.354 18 false 33

Procedure Part Name Code
Z101186

Z101188

Z101187

29 DRAIN HYBRID TRANSAXLE FLUID - - (Click here) -
30 OIL COOLER TUBE SUB-ASSEMBLY 32906F (Click here) - -
31 REAR DRIVE SHAFT ASSEMBLY LH 42340B - - -
32 REAR DRIVE SHAFT ASSEMBLY RH 42330 - - -
33 NO. 1 BOND CABLE 82001 - - -
34 REAR SUSPENSION MEMBER SUB-ASSEMBLY 51206A (Click here) - -
35 REAR LOWER SUSPENSION MEMBER STOPPER 52278C - - -
36 REAR UPPER SUSPENSION MEMBER STOPPER 52277B - - -
37 MOTOR CABLE BRACKET G1143 - - -
38 NO. 2 MOTOR CABLE BRACKET G1143F - - -
39 PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET 46300 (Click here) - -

*1 REAR LOWER SUSPENSION MEMBER STOPPER LH *2 REAR LOWER SUSPENSION MEMBER STOPPER RH

C447199N06
1,2.5 1,1.917 1,1.917 1.167,1.917 true 5.292,1.198 5.708,1.198 true 3.531,0.302 3.948,0.302 true 2.792,2.167 2.958,2.167 2.958,2.167 3.052,1.667 true 6.125,1 6.708,1.313 0.583,0.313 18 false 40 4.031,0.167 4.615,0.479 0.583,0.313 18 false 41 2.49,2.042 2.948,2.365 0.458,0.323 18 false 42 1.24,1.771 1.771,2.104 0.531,0.333 18 false 43 3.448,1.375 3.76,1.573 0.313,0.198 10 false x 2 2.385,0.771 2.698,0.969 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

40 REAR STABILIZER LINK ASSEMBLY LH 48840A (Click here) - -
41 REAR STABILIZER LINK ASSEMBLY RH 48830D - - -
42 REAR STABILIZER BAR 48812 (Click here) - -
43 FCV WITH MOTOR TRANSAXLE ASSEMBLY 30600R - - -

C450026N03
2.417,3.417 3.083,3.417 true 1.75,5.25 2.25,5.25 true 5.542,3.438 6.042,3.438 true 4.885,5.146 5.552,5.146 true 5.677,1.146 6.292,1.146 true 4.958,4.406 4.958,3.99 4.958,3.99 5.125,3.99 true 4.115,5.167 3.948,5.167 3.948,5.167 3.948,4.667 true 5.115,0.49 5.375,0.198 5.375,0.198 5.542,0.198 true 4.385,0.573 4.385,0.156 4.385,0.156 4.208,0.156 true 6.531,3.271 7.083,3.625 0.552,0.354 18 false 47 6.698,1.01 7.156,1.385 0.458,0.375 18 false 48 3.135,3.26 3.688,3.615 0.552,0.354 18 false 46 5.615,5 6.167,5.354 0.552,0.354 18 false 45 2.729,5.073 3.281,5.427 0.552,0.354 18 false 44 4.188,5.083 4.5,5.281 0.313,0.198 10 false *1 5.208,3.906 5.521,4.104 0.313,0.198 10 false *2 5.615,0.094 5.927,0.292 0.313,0.198 10 false *3 3.875,0.063 4.188,0.26 0.313,0.198 10 false *2 0.135,0.083 0.448,0.281 0.313,0.198 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

44 LOWER CONTROL ARM ASSEMBLY LH 48730 (Click here) - -
45 REAR NO. 2 SUSPENSION ARM ASSEMBLY LH 48740F - - -
46 REAR NO. 1 SUSPENSION ARM ASSEMBLY LH 48720A - - -
47 REAR UPPER CONTROL ARM ASSEMBLY LH 48790 (Click here) - -
48 TOE CONTROL LINK SUB-ASSEMBLY LH 48706B (Click here) - -

*A for LH Side - -
*1 REAR NO. 2 SUSPENSION TOE ADJUST PLATE *2 REAR SUSPENSION ARM ATTACHMENT SUB-ASSEMBLY
*3 REAR SUSPENSION TOE ADJUST CAM SUB-ASSEMBLY - -

C447201N05
2.833,0.833 2.833,0.417 2.833,0.417 3.083,0.417 true 5.333,0.667 5.333,0.25 5.333,0.25 5.583,0.25 true 1.75,2 1.75,1.583 1.75,1.583 2,1.583 true 1.25,3.333 1.25,2.917 1.25,2.917 1.406,2.917 true 3,5.583 2.833,5.583 2.833,5.583 2.833,5.167 true 2.385,3.021 2.219,3.021 2.219,3.021 2.219,2.604 true 3.323,3.021 3.156,3.021 3.156,3.021 3.156,2.188 true 6.552,1.333 6.385,1.333 6.385,1.333 6.385,0.917 true 5.583,1.521 5.417,1.521 5.417,1.521 5.417,1.104 true 3.052,5.406 3.604,5.76 0.552,0.354 18 false 49 2.063,1.438 2.615,1.792 0.552,0.354 18 false 50 1.448,2.75 2,3.104 0.552,0.354 18 false 51 3.156,0.25 3.708,0.604 0.552,0.354 18 false 52 5.667,0.104 6.219,0.458 0.552,0.354 18 false 53 2.458,2.927 2.771,3.125 0.313,0.198 10 false *1 3.396,2.927 3.708,3.125 0.313,0.198 10 false *2 5.656,1.438 5.969,1.635 0.313,0.198 10 false *2 6.625,1.24 6.938,1.438 0.313,0.198 10 false *3 0.125,0.094 0.469,0.313 0.344,0.219 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

49 LOWER CONTROL ARM ASSEMBLY RH 48720 - - -
50 REAR NO. 2 SUSPENSION ARM ASSEMBLY RH 48730F - - -
51 REAR NO. 1 SUSPENSION ARM ASSEMBLY RH 48710A - - -
52 REAR UPPER CONTROL ARM ASSEMBLY RH 48770A - - -
53 TOE CONTROL LINK SUB-ASSEMBLY RH 48705 - - -

*A for RH Side - -
*1 REAR NO. 2 SUSPENSION TOE ADJUST PLATE *2 REAR SUSPENSION ARM ATTACHMENT SUB-ASSEMBLY
*3 REAR SUSPENSION ARM ATTACHMENT SUB-ASSEMBLY - -

C447202N04
3.063,5.188 3.188,5.188 3.188,5.188 3.188,4.667 true 1.333,4.25 1.5,4.25 1.5,4.25 1.5,3.75 true 5.5,1.5 5.25,1.5 5.25,1.5 5.25,0.833 true 4.083,1.833 3.833,1.833 3.833,1.833 3.833,1.417 true 5.885,2.781 5.635,2.781 5.635,2.781 5.427,2.344 true 6.083,1.354 6.542,1.688 0.458,0.333 18 false 54 2.74,5.073 3.115,5.396 0.375,0.323 18 false 55 0.958,4.083 1.292,4.438 0.333,0.354 18 false 56 6.365,2.646 6.74,3 0.375,0.354 18 false 57 4.281,1.677 4.615,2.031 0.333,0.354 18 true 58 0.781,4.125 0.969,4.323 0.188,0.198 10 false ● 4.146,1.719 4.333,1.917 0.188,0.198 10 false ● 5.927,1.396 6.115,1.594 0.188,0.198 10 false ● 6.229,2.688 6.417,2.885 0.188,0.198 10 false ● 2.604,5.104 2.792,5.302 0.188,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

54 REAR MOTOR MOUNTING INSULATOR G2371A (Click here) - -
55 REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION LH 52272A (Click here) - -
56 REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION RH 52271E - - -
57 REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for LH Side) 52275A (Click here) - -
58 REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for RH Side) 52275A - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear suspension member removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link

*: The vehicle height changes because of suspension or tire replacement.

·

Rear disc (Including removal and installation)

·

Parking brake shoe (Including removal and installation)

·

Parking brake actuator assembly with bracket (Removed and installed)


Parking brake bedding Electric parking brake system (Click here)
Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)
Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. Have been performed Perform headlight ECU sub-assembly LH initialization
·

Automatic headlight beam level control system

·

Adaptive high beam system


(Click here)
Wheel alignment adjustment Perform "Calibration" Electronically controlled brake system malfunctions (Click here)
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.RELEASE PARKING BRAKE

Z101186

Click here(Click here)

Hide 53292A 3.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 1A906 4.REMOVE FC STACK COVER SUB-ASSEMBLY

Hide G9200A 5.REMOVE FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY)

Z101186

Click here(Click here)

Hide 6.REMOVE CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 7.CHECK TERMINAL VOLTAGE

Z101186

Click here(Click here)

Hide 8.INSTALL CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 64722 9.REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER LH

Hide 10.REMOVE REAR SEAT CUSHION ASSEMBLY LH

Z101186

Click here(Click here)

Hide 72693 11.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 12.REMOVE WIRE HARNESS

a.
C453957C01
4.896,1.469 5.063,1.469 5.063,1.469 5.281,1.146 false 4.646,1.385 4.906,1.573 0.26,0.188 10 false *a 4.844,0.333 5.156,0.531 0.313,0.198 10 false *b 5.708,0.313 6.021,0.51 0.313,0.198 10 false *c
*a Grommet *b Outside of the Vehicle
*c Inside of the Vehicle - -



Hide 13.REMOVE REAR TIRE

Hide 14.FORCED RELEASE PARKING BRAKE

Z101186

Click here(Click here)

Hide 58398F 15.REMOVE NO. 1 FLOOR UNDER COVER

Hide 32912B 16.REMOVE TRANSMISSION OIL COOLER UNDER COVER LH

Hide 32911 17.REMOVE TRANSMISSION OIL COOLER UNDER COVER RH

Hide 52383E 18.REMOVE NO. 1 DIFFERENTIAL SUPPORT PROTECTOR

Hide 52384C 19.REMOVE NO. 2 DIFFERENTIAL SUPPORT PROTECTOR

Hide 53661B 20.REMOVE REAR SUSPENSION BRACE COVER

Hide 75866E 21.REMOVE ROCKER PANEL MOULDING PROTECTOR LH

Hide 65638 22.REMOVE REAR WHEEL HOUSE LINER LH

Hide 46300 23.DISCONNECT PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET

a.
C447203


Hide G1143 24.REMOVE MOTOR CABLE BRACKET

Z101186

CAUTION:

Wear insulated gloves.



a.
C449952


Hide G1148 25.DISCONNECT MOTOR CABLE

Z101186

CAUTION:

Wear insulated gloves.



a.
C447221


Hide 82821T 26.REMOVE CONNECTOR COVER

Z101186

CAUTION:

Wear insulated gloves.



a.
C449953


Hide G114D 27.REMOVE MOTOR CABLE TERMINAL CAP

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:
·

Do not touch the waterproof seal or terminals of the motor cable.

·

When removing the motor cable, make sure not to bent the motor cable base on the FCV transaxle with motor assembly side.




a.
C449954C01
3.667,1.51 3.938,1.833 3.938,1.833 4.125,1.833 true 4.208,1.74 4.521,1.938 0.313,0.198 10 true *1
*1 seal - -



Hide 82H24 28.REMOVE WIRING HARNESS CONNECTOR

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:
·

Do not touch the waterproof seal or terminals of the motor cable.

·

When removing the motor cable, make sure not to bent the motor cable base on the FCV transaxle with motor assembly side.




a.
C449955


Hide 29.DRAIN HYBRID TRANSAXLE FLUID

Z101186

Click here(Click here)

Hide 32906F 30.DISCONNECT OIL COOLER TUBE SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 42340B 31.REMOVE REAR DRIVE SHAFT ASSEMBLY LH

Hide 42330 32.REMOVE REAR DRIVE SHAFT ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 82001 33.REMOVE NO. 1 BOND CABLE

a.
C447204


Hide 51206A 34.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C447205C01
2.615,2.135 2.427,2.135 2.427,2.135 2.313,2.01 true 2.75,1.833 2.833,1.5 2.833,1.5 3,1.5 true 1.188,1.708 1.313,1.708 1.313,1.708 1.396,1.958 true 1.719,1.927 1.875,1.927 true 2.906,1.969 3.094,1.969 true 3.073,1.875 3.281,2.083 0.208,0.208 10 true *b 3.021,1.417 3.302,1.594 0.281,0.177 10 true *a 1.906,1.844 2.146,2.021 0.24,0.177 10 true *a 2.688,2.063 3,2.219 0.313,0.156 10 true *a 0.938,1.594 1.135,1.823 0.198,0.229 10 true *a 0.5,0.115 1.125,0.448 0.625,0.333 18 false i - iii
*a Attachment *b Engine Lifter
V100155

Attachment placement location - -


i.

Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

CAUTION:
·
C323114

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments to keep the rear suspension member sub-assembly level.



ii.

Remove the 4 bolts, rear lower suspension member stopper LH and rear lower suspension member stopper RH.


iii.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.




Hide 52278C 35.REMOVE REAR LOWER SUSPENSION MEMBER STOPPER

a.
C447211


Hide 52277B 36.REMOVE REAR UPPER SUSPENSION MEMBER STOPPER

a.
C447212


Hide G1143 37.REMOVE MOTOR CABLE BRACKET

a.
C447219


Hide G1143F 38.REMOVE NO. 2 MOTOR CABLE BRACKET

a.
C447220


Hide 46300 39.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET

Z101186

Click here(Click here)

Hide 48840A 40.REMOVE REAR STABILIZER LINK ASSEMBLY LH

Z101186

Click here(Click here)

Hide 48830D 41.REMOVE REAR STABILIZER LINK ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 48812 42.REMOVE REAR STABILIZER BAR

Z101186

Click here(Click here)

Hide 30600R 43.REMOVE FCV WITH MOTOR TRANSAXLE ASSEMBLY

Hide 48730 44.REMOVE LOWER CONTROL ARM ASSEMBLY LH

a.
C447206C01
1.688,0.063 1.969,0.417 0.281,0.354 18 false i
V100135

Bolt
V100136

Nut


i.

Remove the bolt, nut and lower control arm assembly LH from the rear suspension member sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.




Hide 48740F 45.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.
C447207


Hide 48720A 46.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C447208C01
1.729,0.083 2.01,0.438 0.281,0.354 18 false i
V100135

Bolt
V100136

Nut



Hide 48790 47.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C447209C01
1.854,0.083 2.135,0.438 0.281,0.354 18 false i
V100135

Bolt
V100136

Nut


i.

Remove the bolt, nut, washer and rear upper control arm assembly LH from the rear suspension member sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.




Hide 48706B 48.REMOVE TOE CONTROL LINK SUB-ASSEMBLY LH

a.
C447210C01
2.104,0.906 2.333,0.385 2.333,0.385 2.052,0.729 true 4.646,0.667 4.896,0.219 4.896,0.219 4.615,0.563 true 0.896,0.146 1.177,0.5 0.281,0.354 18 false i 1.99,2.156 2.271,2.51 0.281,0.354 18 false ii 2.385,0.26 2.719,0.479 0.333,0.219 10 false *a 4.969,0.125 5.302,0.344 0.333,0.219 10 true *a
*a Matchmark - -


i.

Place matchmarks on the rear suspension toe adjust cam sub-assembly, rear No. 2 suspension toe adjust plate and rear suspension member sub-assembly.


ii.

Remove the nut, rear suspension toe adjust cam sub-assembly, rear No. 2 suspension toe adjust plate and toe control link sub-assembly LH from the rear suspension member sub-assembly.



Hide 48720 49.REMOVE LOWER CONTROL ARM ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 48730F 50.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 48710A 51.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 48770A 52.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 48705 53.REMOVE TOE CONTROL LINK SUB-ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide G2371A 54.REMOVE REAR MOTOR MOUNTING INSULATOR

a.
C449956C01
5.25,1.271 5.25,1.438 5.25,1.438 5.75,1.438 false 1.24,1.656 1.24,1.76 1.24,1.76 1.448,1.76 false 1.115,4.104 1.281,4.104 1.281,4.104 1.281,4.271 false 1.615,3.823 1.781,3.823 1.781,3.823 1.781,3.99 false 2.063,3.667 2.229,3.667 2.229,3.667 2.229,3.833 false 2.542,3.5 2.708,3.5 2.708,3.5 2.708,3.667 false 3.438,4.438 3.271,4.438 3.271,4.438 3.271,3.99 false 3.781,4.188 3.604,4.188 3.604,4.188 3.604,3.854 false 4,3.938 3.833,3.938 3.833,3.938 3.833,3.771 false 5.802,1.375 6.26,1.573 0.458,0.198 10 false SST 1.521,1.656 1.979,1.854 0.458,0.198 10 false SST 0.927,4.021 1.385,4.219 0.458,0.198 10 false *a 1.438,3.74 1.896,3.938 0.458,0.198 10 false *a 3.823,4.115 4.281,4.313 0.458,0.198 10 false *a 2.375,3.427 2.833,3.625 0.458,0.198 10 false *b 1.875,3.594 2.333,3.792 0.458,0.198 10 false *b 3.5,4.385 3.958,4.583 0.458,0.198 10 false *a 4.073,3.875 4.531,4.073 0.458,0.198 10 false *a 0.479,0.135 0.76,0.49 0.281,0.354 18 false i
*a SST (09570-24011) *b SST (09570-60010)
V100135

SST bolt location
V100136

Front of the Vehicle


i.

Using SST, remove the rear motor mounting insulator.

SST
09570-24011  
09570-60010  

NOTICE:
·

Before using SST, apply grease to the SST bolts.

·

Be sure to use the correct combination of SST.

·

Do not tilt the bolts of SST.

·

Tighten the 2 bolts of SST so that they enter the 2 holes of the rear motor mounting insulator by an equal amount.



HINT:

Install the 2 SST bolts to the 2 SST holes as shown in the illustration.




Hide 52272A 55.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION LH

a.
C447213N04
2.073,0.104 2.552,0.417 0.479,0.313 18 false i

i.

Using a chisel and hammer, bend the rear suspension member front body mounting cushion rib.



b.
C447214C02
2.25,1.417 3.083,1.417 true 0.583,1.333 1.75,1.333 true 5.927,1.406 6.646,1.406 true 4.646,1.052 5.438,1.052 true 0.479,0.115 0.813,0.438 0.333,0.323 18 false i 4.563,0.094 4.865,0.385 0.302,0.292 18 false ii 3.167,1.323 3.625,1.521 0.458,0.198 10 false SST 0.156,1.25 0.615,1.448 0.458,0.198 10 false SST 6.698,1.323 7.156,1.521 0.458,0.198 10 false SST 4.198,0.969 4.656,1.167 0.458,0.198 10 false SST 2.583,0.208 2.896,0.406 0.313,0.198 10 false *a 6.344,0.333 6.656,0.531 0.313,0.198 10 false *a 6.74,0.823 7.052,1.021 0.313,0.198 10 true *b
*a Turn *b Hold


i.

Using SST, remove the rear suspension member front body mounting cushion LH while applying grease into the clearance between the rear suspension member front body mounting cushion LH and the rear suspension member sub-assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09957-04010, 09958-04011)
09950-60011  (09951-00540)

NOTICE:
·

Apply grease to the threads and tip of the SST center bolt before use.

·

Be careful as the rear suspension member front body mounting cushion LH may fly out.

·

The rear suspension member front body mounting cushion LH cannot be reused.




ii.

If the outer casing of the rear suspension member front body mounting cushion remains, insert SST between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly, and then remove the outer casing. SST

SST
09608-06041  
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09957-04010, 09958-04011)
09950-60011  (09951-00540)
09950-60021  (09951-00680)



Hide 52271E 56.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION RH

a.

Perform the same procedure as for the LH side.


Hide 52275A 57.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for LH Side)

a.
C447215C03
2.135,1.385 2.927,1.385 true 0.771,1.646 1.563,1.646 true 5.479,1.156 6.271,1.156 true 4.229,1.365 5.021,1.365 true 0.448,0.104 1.146,0.417 0.698,0.313 18 false i 4.531,0.104 4.958,0.458 0.427,0.354 18 false ii 2.74,0.573 3.052,0.771 0.313,0.198 10 false *a 0.802,1.021 1.115,1.219 0.313,0.198 10 true *b 5.917,0.198 6.229,0.396 0.313,0.198 10 false *a 4.604,1.115 4.917,1.313 0.313,0.198 10 true *b 2.99,1.302 3.448,1.5 0.458,0.198 10 true SST 0.396,1.542 0.76,1.75 0.365,0.208 10 true SST 6.302,1.073 6.76,1.271 0.458,0.198 10 true SST 3.875,1.26 4.24,1.469 0.365,0.208 10 true SST
*a Turn *b Hold


i.

Using SST, remove the rear suspension member rear body mounting cushion while applying grease into the clearance between the rear suspension member rear body mounting cushion and the rear suspension member sub-assembly.

SST
09608-06041  
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60011  (09951-00540)

NOTICE:
·

Apply grease to the threads and tip of the SST center bolt before use.

·

Be careful as the rear suspension member rear body mounting cushion may fly out.

·

The rear suspension member rear body mounting cushion cannot be reused.




ii.

If the outer casing of the rear suspension member rear body mounting cushion remains, insert SST between the rear suspension member rear body mounting cushion and the rear suspension member sub-assembly, and then remove the outer casing. SST

SST
09608-06041  
09950-00020  
09950-00030  
09950-60021  (09951-00680)



Hide 52275A 58.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for RH Side)

a.

Perform the same procedure as for the LH side.