Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM37H0E _59 Vehicle Exterior _095212 WIPER / WASHER _0447384 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rear Cleaner Motor and Relay Circuit  


DESCRIPTION

When the main body ECU (multiplex network body ECU) receives a washer switch (CAMERA) signal from the windshield wiper switch assembly, the rear lidar sensor cleaner relay (LIDAR CLN RR/CAMERA CLN) operates to spray the windshield washer.

WIRING DIAGRAM

E459327E03
5.396,3.938 7.042,4.375 1.646,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 3.24,0.333 4.646,0.542 1.406,0.208 10 false from Auxiliary Battery 5.375,3.75 5.833,3.948 0.458,0.198 10 false D12 5.75,2.75 6.365,2.948 0.615,0.198 10 false RWSR 5.458,2.646 5.771,2.844 0.313,0.198 10 false 23 4.625,1.469 4.781,1.667 0.156,0.198 10 false 5 3.708,1.479 3.865,1.677 0.156,0.198 10 false 3 4.625,2.635 4.781,2.833 0.156,0.198 10 false 2 3.688,2.646 3.844,2.844 0.156,0.198 10 false 1 0.896,2.042 1.354,2.24 0.458,0.198 10 false A57 3.313,3.146 5.198,3.573 1.885,0.427 10 false Camera Cleaner Relay (LIDAR CLN RR/CAMERA CLN) 0.885,2.219 3.125,2.448 2.24,0.229 10 false Washer Motor and Pump Assembly 0.948,1.469 1.104,1.667 0.156,0.198 10 false 1 2.906,1.469 3.063,1.667 0.156,0.198 10 false 2 0.188,2.74 1.208,2.958 1.021,0.219 10 false from IG1 Relay 2.49,1.469 2.948,1.667 0.458,0.198 10 false GND 1.156,1.479 1.469,1.677 0.313,0.198 10 false IG 1.875,2.938 2.813,3.146 0.938,0.208 10 false R/B-IG1 NO. 2 0.542,0.552 2.813,0.823 2.271,0.271 10 false LIDAR CLN MTR RR/CAMERA CLN

CAUTION / NOTICE / HINT

NOTICE:
·

First check that the windshield washer function operates normally.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>OPERATION CHECK

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Washer Relay Operates the camera cleaner relay (LIDAR CLN RR/CAMERA CLN) OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Rear Washer Relay
50004 123 89
OK:

Camera cleaner relay (LIDAR CLN RR/CAMERA CLN) is operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK WASHER MOTOR AND PUMP ASSEMBLY
2.CHECK WASHER MOTOR AND PUMP ASSEMBLY

OK

3.INSPECT CAMERA CLEANER RELAY (LIDAR CLN RR/CAMERA CLN)

NG

REPLACE WASHER MOTOR AND PUMP ASSEMBLY

3.INSPECT CAMERA CLEANER RELAY (LIDAR CLN RR/CAMERA CLN)

OK

4.CHECK HARNESS AND CONNECTOR (REAR WASHER MOTOR AND PUMP ASSEMBLY - CAMERA CLEANER RELAY [LIDAR CLN RR/CAMERA CLN] AND BATTERY)

NG

REPLACE CAMERA CLEANER RELAY (LIDAR CLN RR/CAMERA CLN)

4.CHECK HARNESS AND CONNECTOR (REAR WASHER MOTOR AND PUMP ASSEMBLY - CAMERA CLEANER RELAY [LIDAR CLN RR/CAMERA CLN] AND BATTERY)
a.

Disconnect the A57 washer motor and pump assembly connector.


b.

Remove the camera cleaner relay (LIDAR CLN RR/CAMERA CLN) from the No. 1 front compartment relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A57)Location & Routing

Click Connector(A57)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Washer Motor & Pump Assembly

A57-2 (GND) - Camera cleaner relay (LIDAR CLN RR/CAMERA CLN) terminal 3 Always Below 1 Ω
A57-2 (GND) or Camera cleaner relay (LIDAR CLN RR/CAMERA CLN) terminal 3 - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A57)Location & Routing

Click Connector(A57)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Washer Motor & Pump Assembly

A57-1 (IG) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CAMERA CLEANER RELAY [LIDAR CLN RR/CAMERA CLN] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CAMERA CLEANER RELAY [LIDAR CLN RR/CAMERA CLN] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BATTERY)
a.

Remove the camera cleaner relay (LIDAR CLN RR/CAMERA CLN) from the No. 1 front compartment relay block.


b.

Disconnect the D12 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D12)Location & Routing

Click Connector(D12)Instrument Panel>Instrument Panel Wire>Main Body ECU

Camera cleaner relay (LIDAR CLN RR/CAMERA CLN) terminal 2 - D12-23 (RWSR) Always Below 1 Ω
Camera cleaner relay (LIDAR CLN RR/CAMERA CLN) terminal 5 - Body ground Always Below 1 Ω
Camera cleaner relay (LIDAR CLN RR/CAMERA CLN) terminal 2 or D12-23 (RWSR) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Camera cleaner relay (LIDAR CLN RR/CAMERA CLN) terminal 1 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR