Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0453477 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P1A8000  Hybrid/EV Battery Stack 1 Delta SOC High  P1A8500  Hybrid/EV Battery Stack 2 Delta SOC High  


DESCRIPTION

The EV supply battery assembly is composed of 84 cells (3.7 V each) in series. The battery ECU assembly monitors the difference in capacity of each EV battery cell to detect malfunctions of the EV supply battery assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1A8000 Hybrid/EV Battery Stack 1 Delta SOC High The difference in capacity of each cell of the No. 1 EV supply stack sub-assembly exceeds the specified value.
(2 trip detection logic)
·

No. 1 EV supply stack sub-assembly

·

EV battery terminal block

·

Battery voltage sensor (for upper side)


Master Warning:
Comes on
EV Battery A
P1A8500 Hybrid/EV Battery Stack 2 Delta SOC High The difference in capacity of each cell of the No. 2 EV supply stack sub-assembly exceeds the specified value.
(2 trip detection logic)
·

No. 2 EV supply stack sub-assembly

·

EV battery terminal block

·

Battery voltage sensor (for lower side)


Master Warning:
Comes on
EV Battery A

Related Data List
DTC No. Data List
P1A8000
·

Hybrid/EV Battery Cell 1 to 84 Voltage

·

Hybrid/EV Battery Cell 1 to 84 Internal Resistance

·

Hybrid/EV Battery SOC

·

Hybrid/EV Battery Current

·

Hybrid/EV Battery Voltage


P1A8500

HINT:
·

These DTCs can be stored after clearing the DTCs and driving the vehicle for approximately 12 minutes.

·

In order to ensure EV supply battery assembly performance, appropriate cooling performance must be maintained. Perform the following items as necessary. If cooling performance has decreased and "Maintenance Required for Traction Battery Cooling Parts See Owner's Manual" is displayed on the multi-information display, make sure to perform the following items:

-

Make sure the air intake port for EV supply battery assembly is not blocked.


-

Make sure there are no gaps between the connecting parts of the ducts.


-

Clean the No. 1 EV battery intake filter and No. 2 EV battery intake filter.

Clear the DTCs to reset the learning values even if no DTCs are stored.





CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Drive the vehicle on urban roads for approximately 12 minutes or more.

(As 2 trip detection logic is used, check for DTCs including pending DTCs.)

4.

Enter the following menus: Powertrain / EV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an EV supply battery assembly, make sure to return it through an authorized collection agent who is capable of handling it safely. If the EV supply battery assembly is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the EV supply battery assembly is disposed of improperly or abandoned. Therefore, make sure to return all EV supply battery assemblies through an authorized collection agent.


·

Before returning the EV supply battery assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the EV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the EV supply battery assembly and EV supply stack sub-assemblies.

·
A358020

After removing the EV supply battery assembly, keep it away from water. Exposure to water may cause the EV supply battery assembly to produce heat, resulting in a fire.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV BATTERY, EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV Battery > Trouble Codes
50001 398
Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
Only P1A8000 or P1A8500 for Hybrid battery system is output A
P1A8000 or P1A8500 is output and DTCs other than the DTCs in the table below are output B
P1A8000 or P1A8500 is output and Hybrid battery system DTCs in the table below are output C
P1A8000 or P1A8500 is output and Hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
P0ABF2A Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range
P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open
P1CC81E Hybrid/EV Battery Stack 1 Voltage Difference Out of Range
P1CC91E Hybrid/EV Battery Stack 2 Voltage Difference Out of Range
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation
P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range
P1C2D62 Hybrid/EV Battery "A" Voltage Sensor/ Boosting Converter Voltage Sensor "A" Signal Compare Failure


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK ODOMETER

B

2.CHECK ODOMETER

C

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

D

2.CHECK ODOMETER
a.

Check and record the total distance traveled of the vehicle.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
"P1A8000" is also output. A
"P1A8500" is also output. B



A

4.CHECK FREEZE FRAME DATA

B

8.CHECK FREEZE FRAME DATA
4.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

a.

Read the value of freeze frame data items "Hybrid/EV Battery Cell 1 Voltage" through "Hybrid/EV Battery Cell 42 Voltage" for DTC P1A8000 and make a note if the value of any is the lowest voltage value.

HINT:

Use this for reference when measuring the battery voltage sensor resistance.


Powertrain > EV Battery > DTC(P1A8000) > Freeze Frame Data
Tester Display
Hybrid/EV Battery Cell 1 Voltage
Hybrid/EV Battery Cell 2 Voltage
Hybrid/EV Battery Cell 3 Voltage
Hybrid/EV Battery Cell 4 Voltage
Hybrid/EV Battery Cell 5 Voltage
Hybrid/EV Battery Cell 6 Voltage
Hybrid/EV Battery Cell 7 Voltage
Hybrid/EV Battery Cell 8 Voltage
Hybrid/EV Battery Cell 9 Voltage
Hybrid/EV Battery Cell 10 Voltage
Hybrid/EV Battery Cell 11 Voltage
Hybrid/EV Battery Cell 12 Voltage
Hybrid/EV Battery Cell 13 Voltage
Hybrid/EV Battery Cell 14 Voltage
Hybrid/EV Battery Cell 15 Voltage
Hybrid/EV Battery Cell 16 Voltage
Hybrid/EV Battery Cell 17 Voltage
Hybrid/EV Battery Cell 18 Voltage
Hybrid/EV Battery Cell 19 Voltage
Hybrid/EV Battery Cell 20 Voltage
Hybrid/EV Battery Cell 21 Voltage
Hybrid/EV Battery Cell 22 Voltage
Hybrid/EV Battery Cell 23 Voltage
Hybrid/EV Battery Cell 24 Voltage
Hybrid/EV Battery Cell 25 Voltage
Hybrid/EV Battery Cell 26 Voltage
Hybrid/EV Battery Cell 27 Voltage
Hybrid/EV Battery Cell 28 Voltage
Hybrid/EV Battery Cell 29 Voltage
Hybrid/EV Battery Cell 30 Voltage
Hybrid/EV Battery Cell 31 Voltage
Hybrid/EV Battery Cell 32 Voltage
Hybrid/EV Battery Cell 33 Voltage
Hybrid/EV Battery Cell 34 Voltage
Hybrid/EV Battery Cell 35 Voltage
Hybrid/EV Battery Cell 36 Voltage
Hybrid/EV Battery Cell 37 Voltage
Hybrid/EV Battery Cell 38 Voltage
Hybrid/EV Battery Cell 39 Voltage
Hybrid/EV Battery Cell 40 Voltage
Hybrid/EV Battery Cell 41 Voltage
Hybrid/EV Battery Cell 42 Voltage
50040 398 334,335,336,337,338,339,340,341,342,343,344,345,346,347,348,349,350,351,352,353,354,355,356,357,358,359,360,361,362,363,364,365,366,367,368,369,370,371,372,373,374,375 P1A8000

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

5.CHECK BATTERY VOLTAGE SENSOR (for Upper Side) (VA1 - VA42)
5.CHECK BATTERY VOLTAGE SENSOR (for Upper Side) (VA1 - VA42)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the battery voltage sensor (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When disconnecting connector y1 of the battery voltage sensor (for upper side), first disconnect connectors z14 and z15 from the battery voltage sensor (for upper side).


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the EV battery cells which measured the lowest voltage value in the previous step.


C371968C06
1.594,1.792 1.99,2.021 0.396,0.229 5.021,1.802 5.417,2.031 0.396,0.229 1.74,4.323 1.75,3.75 true 0.688,3.427 0.438,2.719 true 0.844,3.427 0.573,2.385 true 1,3.448 0.885,2.719 true 1.135,3.417 1.083,2.354 true 1.271,3.427 1.313,2.708 true 2.344,3.406 2.198,2.729 true 2.5,3.417 2.365,2.333 true 2.625,3.427 2.635,2.729 true 2.792,3.448 2.917,2.333 true 0.26,4.344 0.76,3.75 true 0.344,4.74 0.865,3.76 true 0.813,4.313 1.156,3.75 true 0.896,4.719 1.323,3.75 true 1.323,4.313 1.458,3.729 true 1.49,4.74 1.594,3.74 true 1.969,4.729 1.896,3.74 true 2.198,4.313 2.031,3.729 true 2.521,4.74 2.188,3.74 true 2.625,4.292 2.333,3.74 true 2.615,4.292 2.323,3.74 true 3.094,4.719 2.458,3.719 true 3.135,4.333 2.708,3.719 true 3.208,4 2.875,3.719 true 3.698,4.729 4.344,3.75 true 4.219,4.333 4.635,3.74 true 4.313,4.708 4.792,3.74 true 4.76,4.333 4.938,3.75 true 4.948,4.719 5.063,3.76 true 5.208,4.333 5.219,3.74 true 5.448,4.698 5.375,3.74 true 5.667,4.354 5.5,3.771 true 5.969,4.698 5.646,3.74 true 6.063,4.333 5.771,3.75 true 6.563,4.708 5.927,3.729 true 6.615,4.292 6.229,3.74 true 6.677,4.021 6.344,3.74 true 4.438,3.417 4.125,2.708 true 4.594,3.406 4.375,2.333 true 4.74,3.417 4.719,2.729 true 5.823,3.406 5.469,2.323 true 6.083,3.396 6.063,2.302 true 6.375,3.417 6.813,2.344 true 5.958,3.406 5.844,2.719 true 6.24,3.406 6.302,2.729 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 0.198,4.792 0.667,4.969 0.469,0.177 10 false VA3 0.208,2.542 0.604,2.719 0.396,0.177 10 false GA0 0.417,2.177 0.885,2.354 0.469,0.177 10 false VA2 0.76,2.552 1.229,2.729 0.469,0.177 10 false VA4 0.979,2.177 1.448,2.354 0.469,0.177 10 false VA5 1.208,2.552 1.677,2.729 0.469,0.177 10 false VA7 1.969,2.552 2.438,2.729 0.469,0.177 10 false VA16 2.208,2.177 2.677,2.354 0.469,0.177 10 false VA18 2.49,2.552 2.958,2.729 0.469,0.177 10 false VA19 2.781,2.177 3.25,2.354 0.469,0.177 10 false VA21 0.073,4.375 0.542,4.552 0.469,0.177 10 false VA1 0.635,4.375 0.958,4.563 0.323,0.188 10 false VA6 0.74,4.792 1.063,4.979 0.323,0.188 10 false VA8 1.167,4.375 1.49,4.563 0.323,0.188 10 false VA9 1.313,4.781 1.781,4.958 0.469,0.177 10 false VA10 1.583,4.375 2.052,4.552 0.469,0.177 10 false VA11 1.823,4.781 2.292,4.958 0.469,0.177 10 false VA12 2.031,4.375 2.5,4.552 0.469,0.177 10 false VA13 2.365,4.792 2.833,4.969 0.469,0.177 10 false VA14 2.542,4.385 3.01,4.563 0.469,0.177 10 false VA15 2.969,4.792 3.438,4.969 0.469,0.177 10 false VA17 3.115,4.052 3.583,4.229 0.469,0.177 10 false VA22 3.042,4.385 3.51,4.563 0.469,0.177 10 false VA20 3.563,4.792 4.031,4.969 0.469,0.177 10 false GA1 6.667,2.177 7.135,2.354 0.469,0.177 10 false VA42 4.021,4.385 4.49,4.563 0.469,0.177 10 false VA25 4.135,4.792 4.604,4.969 0.469,0.177 10 false VA27 4.583,4.385 5.052,4.563 0.469,0.177 10 false VA28 4.771,4.792 5.24,4.969 0.469,0.177 10 false VA29 5.052,4.385 5.521,4.563 0.469,0.177 10 false VA30 5.292,4.792 5.76,4.969 0.469,0.177 10 false VA31 5.51,4.385 5.979,4.563 0.469,0.177 10 false VA32 5.823,4.792 6.292,4.969 0.469,0.177 10 false VA33 5.958,4.385 6.427,4.563 0.469,0.177 10 false VA34 6.438,4.792 6.906,4.969 0.469,0.177 10 false VA36 6.51,4.385 6.979,4.563 0.469,0.177 10 false VA39 6.646,4.104 7.115,4.281 0.469,0.177 10 false VA41 3.917,2.552 4.385,2.729 0.469,0.177 10 false VA23 4.573,2.552 5.042,2.729 0.469,0.177 10 false VA26 5.677,2.552 6.146,2.729 0.469,0.177 10 false VA37 6.156,2.552 6.625,2.729 0.469,0.177 10 false VA40 4.219,2.177 4.688,2.354 0.469,0.177 10 false VA24 5.292,2.177 5.76,2.354 0.469,0.177 10 false VA35 5.927,2.177 6.396,2.354 0.469,0.177 10 false VA38 1.677,1.813 2.052,2 0.375,0.188 10 false z14 5.104,1.833 5.427,2.031 0.323,0.198 10 false z15
*a Component without harness connected
(Battery Voltage Sensor (for Upper Side))
- -


Standard Resistance:
Tester Connection
(Tester Probe Polarity)
EV Battery Cell Condition Specified Condition

Click Location & Routing(z14,z15)Location & Routing

Click Connector(z14)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Upper)

Click Connector(z15)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Upper)

z14-10 (GA0) (-) - z14-24 (VA1) (+) 1 Always 50 kΩ or higher
z14-24 (VA1) (-) - z14-9 (VA2) (+) 2 Always 50 kΩ or higher
z14-9 (VA2) (-) - z14-23 (VA3) (+) 3 Always 50 kΩ or higher
z14-23 (VA3) (-) - z14-8 (VA4) (+) 4 Always 50 kΩ or higher
z14-8 (VA4) (-) - z14-7 (VA5) (+) 5 Always 50 kΩ or higher
z14-7 (VA5) (-) - z14-22 (VA6) (+) 6 Always 50 kΩ or higher
z14-22 (VA6) (-) - z14-6 (VA7) (+) 7 Always 50 kΩ or higher
z14-6 (VA7) (-) - z14-21 (VA8) (+) 8 Always 50 kΩ or higher
z14-21 (VA8) (-) - z14-20 (VA9) (+) 9 Always 50 kΩ or higher
z14-20 (VA9) (-) - z14-19 (VA10) (+) 10 Always 50 kΩ or higher
z14-19 (VA10) (-) - z14-18 (VA11) (+) 11 Always 50 kΩ or higher
z14-18 (VA11) (-) - z14-17 (VA12) (+) 12 Always 50 kΩ or higher
z14-17 (VA12) (-) - z14-16 (VA13) (+) 13 Always 50 kΩ or higher
z14-16 (VA13) (-) - z14-15 (VA14) (+) 14 Always 50 kΩ or higher
z14-15 (VA14) (-) - z14-14 (VA15) (+) 15 Always 50 kΩ or higher
z14-14 (VA15) (-) - z14-5 (VA16) (+) 16 Always 50 kΩ or higher
z14-5 (VA16) (-) - z14-13 (VA17) (+) 17 Always 50 kΩ or higher
z14-13 (VA17) (-) - z14-4 (VA18) (+) 18 Always 50 kΩ or higher
z14-4 (VA18) (-) - z14-3 (VA19) (+) 19 Always 50 kΩ or higher
z14-3 (VA19) (-) - z14-12 (VA20) (+) 20 Always 50 kΩ or higher
z14-12 (VA20) (-) - z14-2 (VA21) (+) 21 Always 50 kΩ or higher
z14-2 (VA21) (-) - z14-11 (VA22) (+) 22 Always 50 kΩ or higher
z15-23 (GA1) (-) - z15-8 (VA23) (+) 23 Always 50 kΩ or higher
z15-8 (VA23) (-) - z15-7 (VA24) (+) 24 Always 50 kΩ or higher
z15-7 (VA24) (-) - z15-22 (VA25) (+) 25 Always 50 kΩ or higher
z15-22 (VA25) (-) - z15-6 (VA26) (+) 26 Always 50 kΩ or higher
z15-6 (VA26) (-) - z15-21 (VA27) (+) 27 Always 50 kΩ or higher
z15-21 (VA27) (-) - z15-20 (VA28) (+) 28 Always 50 kΩ or higher
z15-20 (VA28) (-) - z15-19 (VA29) (+) 29 Always 50 kΩ or higher
z15-19 (VA29) (-) - z15-18 (VA30) (+) 30 Always 50 kΩ or higher
z15-18 (VA30) (-) - z15-17 (VA31) (+) 31 Always 50 kΩ or higher
z15-17 (VA31) (-) - z15-16 (VA32) (+) 32 Always 50 kΩ or higher
z15-16 (VA32) (-) - z15-15 (VA33) (+) 33 Always 50 kΩ or higher
z15-15 (VA33) (-) - z15-14 (VA34) (+) 34 Always 50 kΩ or higher
z15-14 (VA34) (-) - z15-5 (VA35) (+) 35 Always 50 kΩ or higher
z15-5 (VA35) (-) - z15-13 (VA36) (+) 36 Always 50 kΩ or higher
z15-13 (VA36) (-) - z15-4 (VA37) (+) 37 Always 50 kΩ or higher
z15-4 (VA37) (-) - z15-3 (VA38) (+) 38 Always 50 kΩ or higher
z15-3 (VA38) (-) - z15-12 (VA39) (+) 39 Always 50 kΩ or higher
z15-12 (VA39) (-) - z15-2 (VA40) (+) 40 Always 50 kΩ or higher
z15-2 (VA40) (-) - z15-11 (VA41) (+) 41 Always 50 kΩ or higher
z15-11 (VA41) (-) - z15-1 (VA42) (+) 42 Always 50 kΩ or higher


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Read the resistance after the value has stabilized.

·

In order to avoid damaging the terminals of the battery voltage sensor, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of the battery voltage sensor.




Result:
Result Proceed to
The resistance between the terminals is 50 kΩ or higher. A
Other than above B


Post-procedure1

a.

Install the battery voltage sensor (for upper side).

CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When connecting connectors z14 and z15 of the battery voltage sensor (for upper side), first connect connector y1 to the battery voltage sensor (for upper side).




A

6.CHECK TOTAL DISTANCE DRIVEN

B

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)

6.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

B

7.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
7.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

8.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

a.

Read the value of freeze frame data items "Hybrid/EV Battery Cell 43 Voltage" through "Hybrid/EV Battery Cell 84 Voltage" for DTC P1A8500 and make a note if the value of any is the lowest voltage value.

HINT:

Use this for reference when measuring the battery voltage sensor resistance.


Powertrain > EV Battery > DTC(P1A8500) > Freeze Frame Data
Tester Display
Hybrid/EV Battery Cell 43 Voltage
Hybrid/EV Battery Cell 44 Voltage
Hybrid/EV Battery Cell 45 Voltage
Hybrid/EV Battery Cell 46 Voltage
Hybrid/EV Battery Cell 47 Voltage
Hybrid/EV Battery Cell 48 Voltage
Hybrid/EV Battery Cell 49 Voltage
Hybrid/EV Battery Cell 50 Voltage
Hybrid/EV Battery Cell 51 Voltage
Hybrid/EV Battery Cell 52 Voltage
Hybrid/EV Battery Cell 53 Voltage
Hybrid/EV Battery Cell 54 Voltage
Hybrid/EV Battery Cell 55 Voltage
Hybrid/EV Battery Cell 56 Voltage
Hybrid/EV Battery Cell 57 Voltage
Hybrid/EV Battery Cell 58 Voltage
Hybrid/EV Battery Cell 59 Voltage
Hybrid/EV Battery Cell 60 Voltage
Hybrid/EV Battery Cell 61 Voltage
Hybrid/EV Battery Cell 62 Voltage
Hybrid/EV Battery Cell 63 Voltage
Hybrid/EV Battery Cell 64 Voltage
Hybrid/EV Battery Cell 65 Voltage
Hybrid/EV Battery Cell 66 Voltage
Hybrid/EV Battery Cell 67 Voltage
Hybrid/EV Battery Cell 68 Voltage
Hybrid/EV Battery Cell 69 Voltage
Hybrid/EV Battery Cell 70 Voltage
Hybrid/EV Battery Cell 71 Voltage
Hybrid/EV Battery Cell 72 Voltage
Hybrid/EV Battery Cell 73 Voltage
Hybrid/EV Battery Cell 74 Voltage
Hybrid/EV Battery Cell 75 Voltage
Hybrid/EV Battery Cell 76 Voltage
Hybrid/EV Battery Cell 77 Voltage
Hybrid/EV Battery Cell 78 Voltage
Hybrid/EV Battery Cell 79 Voltage
Hybrid/EV Battery Cell 80 Voltage
Hybrid/EV Battery Cell 81 Voltage
Hybrid/EV Battery Cell 82 Voltage
Hybrid/EV Battery Cell 83 Voltage
Hybrid/EV Battery Cell 84 Voltage
50040 398 376,377,378,379,380,381,382,383,384,385,386,387,388,389,390,391,392,393,394,395,396,397,398,399,400,401,402,403,404,405,406,407,408,409,410,411,412,413,414,415,416,417 P1A8500

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

9.CHECK BATTERY VOLTAGE SENSOR (for Lower Side) (VA43 - VA84)
9.CHECK BATTERY VOLTAGE SENSOR (for Lower Side) (VA43 - VA84)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the battery voltage sensor (for lower side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When disconnecting connector y3 of the battery voltage sensor (for lower side), first disconnect connectors z16 and z17 from the battery voltage sensor (for lower side).


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the EV battery cells which measured the lowest voltage value in the previous step.


C371968C07
1.594,1.792 1.99,2.021 0.396,0.229 5.021,1.802 5.417,2.031 0.396,0.229 1.74,4.323 1.75,3.75 true 0.688,3.427 0.438,2.719 true 0.844,3.427 0.573,2.385 true 1,3.448 0.885,2.719 true 1.135,3.417 1.083,2.354 true 1.271,3.427 1.313,2.708 true 2.344,3.406 2.198,2.729 true 2.5,3.417 2.365,2.354 true 2.625,3.427 2.635,2.729 true 2.792,3.448 2.917,2.365 true 0.26,4.344 0.76,3.75 true 0.344,4.74 0.865,3.76 true 0.813,4.313 1.156,3.75 true 0.896,4.719 1.323,3.75 true 1.323,4.313 1.458,3.729 true 1.49,4.74 1.594,3.74 true 1.969,4.729 1.896,3.74 true 2.198,4.313 2.031,3.729 true 2.521,4.74 2.188,3.74 true 2.625,4.292 2.333,3.74 true 2.615,4.292 2.323,3.74 true 3.094,4.719 2.458,3.719 true 3.135,4.333 2.708,3.719 true 3.208,4 2.875,3.719 true 3.698,4.729 4.344,3.75 true 4.219,4.333 4.635,3.74 true 4.313,4.708 4.792,3.74 true 4.76,4.333 4.938,3.75 true 4.948,4.719 5.063,3.76 true 5.208,4.333 5.219,3.74 true 5.448,4.698 5.375,3.74 true 5.667,4.354 5.5,3.771 true 5.969,4.698 5.646,3.74 true 6.063,4.333 5.771,3.75 true 6.563,4.708 5.927,3.729 true 6.615,4.292 6.229,3.74 true 6.677,4.021 6.344,3.74 true 4.438,3.417 4.125,2.708 true 4.594,3.406 4.375,2.354 true 4.74,3.417 4.719,2.729 true 5.823,3.406 5.479,2.344 true 6.083,3.396 6.063,2.344 true 6.375,3.417 6.813,2.365 true 5.958,3.406 5.844,2.719 true 6.24,3.406 6.302,2.729 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 0.198,4.802 0.667,4.979 0.469,0.177 10 false VA45 0.208,2.542 0.604,2.719 0.396,0.177 10 false GA2 0.417,2.177 0.885,2.354 0.469,0.177 10 false VA44 0.719,2.552 1.188,2.729 0.469,0.177 10 false VA46 0.948,2.177 1.417,2.354 0.469,0.177 10 false VA47 1.167,2.552 1.635,2.729 0.469,0.177 10 false VA49 1.969,2.552 2.438,2.729 0.469,0.177 10 false VA58 2.208,2.177 2.677,2.354 0.469,0.177 10 false VA60 2.49,2.552 2.958,2.729 0.469,0.177 10 false VA61 2.781,2.177 3.25,2.354 0.469,0.177 10 false VA63 0.073,4.375 0.542,4.552 0.469,0.177 10 false VA43 0.594,4.375 1.021,4.573 0.427,0.198 10 false VA48 0.698,4.792 1.125,5.01 0.427,0.219 10 false VA50 1.125,4.375 1.521,4.563 0.396,0.188 10 false VA51 1.313,4.781 1.781,4.958 0.469,0.177 10 false VA52 1.583,4.375 2.052,4.552 0.469,0.177 10 false VA53 1.823,4.781 2.292,4.958 0.469,0.177 10 false VA54 2.031,4.375 2.5,4.552 0.469,0.177 10 false VA55 2.365,4.792 2.833,4.969 0.469,0.177 10 false VA56 2.542,4.385 3.01,4.563 0.469,0.177 10 false VA57 2.969,4.792 3.438,4.969 0.469,0.177 10 false VA59 3.115,4.052 3.583,4.229 0.469,0.177 10 false VA64 3.042,4.385 3.51,4.563 0.469,0.177 10 false VA62 3.563,4.792 4.031,4.969 0.469,0.177 10 false GA3 6.667,2.177 7.135,2.354 0.469,0.177 10 false VA84 4.021,4.385 4.49,4.563 0.469,0.177 10 false VA67 4.135,4.792 4.604,4.969 0.469,0.177 10 false VA69 4.583,4.385 5.052,4.563 0.469,0.177 10 false VA70 4.771,4.792 5.24,4.969 0.469,0.177 10 false VA71 5.052,4.385 5.521,4.563 0.469,0.177 10 false VA72 5.292,4.792 5.76,4.969 0.469,0.177 10 false VA73 5.51,4.385 5.979,4.563 0.469,0.177 10 false VA74 5.823,4.792 6.292,4.969 0.469,0.177 10 false VA75 5.958,4.385 6.427,4.563 0.469,0.177 10 false VA76 6.438,4.792 6.906,4.969 0.469,0.177 10 false VA78 6.51,4.385 6.979,4.563 0.469,0.177 10 false VA81 6.646,4.104 7.115,4.281 0.469,0.177 10 false VA83 3.917,2.552 4.385,2.729 0.469,0.177 10 false VA65 4.573,2.552 5.042,2.729 0.469,0.177 10 false VA68 5.677,2.552 6.146,2.729 0.469,0.177 10 false VA79 6.156,2.552 6.625,2.729 0.469,0.177 10 false VA82 4.219,2.177 4.688,2.354 0.469,0.177 10 false VA66 5.292,2.177 5.76,2.354 0.469,0.177 10 false VA77 5.927,2.177 6.396,2.354 0.469,0.177 10 false VA80 1.677,1.823 2.052,2.01 0.375,0.188 10 false z16 5.115,1.844 5.438,2.042 0.323,0.198 10 false z17
*a Component without harness connected
(Battery Voltage Sensor (for Lower Side))
- -


Standard Resistance:
Tester Connection
(Tester Probe Polarity)
EV Battery Cell Condition Specified Condition

Click Location & Routing(z16,z17)Location & Routing

Click Connector(z16)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Lower)

Click Connector(z17)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Lower)

z16-10 (GA2) (-) - z16-24 (VA43) (+) 43 Always 50 kΩ or higher
z16-24 (VA43) (-) - z16-9 (VA44) (+) 44 Always 50 kΩ or higher
z16-9 (VA44) (-) - z16-23 (VA45) (+) 45 Always 50 kΩ or higher
z16-23 (VA45) (-) - z16-8 (VA46) (+) 46 Always 50 kΩ or higher
z16-8 (VA46) (-) - z16-7 (VA47) (+) 47 Always 50 kΩ or higher
z16-7 (VA47) (-) - z16-22 (VA48) (+) 48 Always 50 kΩ or higher
z16-22 (VA48) (-) - z16-6 (VA49) (+) 49 Always 50 kΩ or higher
z16-6 (VA49) (-) - z16-21 (VA50) (+) 50 Always 50 kΩ or higher
z16-21 (VA50) (-) - z16-20 (VA51) (+) 51 Always 50 kΩ or higher
z16-20 (VA51) (-) - z16-19 (VA52) (+) 52 Always 50 kΩ or higher
z16-19 (VA52) (-) - z16-18 (VA53) (+) 53 Always 50 kΩ or higher
z16-18 (VA53) (-) - z16-17 (VA54) (+) 54 Always 50 kΩ or higher
z16-17 (VA54) (-) - z16-16 (VA55) (+) 55 Always 50 kΩ or higher
z16-16 (VA55) (-) - z16-15 (VA56) (+) 56 Always 50 kΩ or higher
z16-15 (VA56) (-) - z16-14 (VA57) (+) 57 Always 50 kΩ or higher
z16-14 (VA57) (-) - z16-5 (VA58) (+) 58 Always 50 kΩ or higher
z16-5 (VA58) (-) - z16-13 (VA59) (+) 59 Always 50 kΩ or higher
z16-13 (VA59) (-) - z16-4 (VA60) (+) 60 Always 50 kΩ or higher
z16-4 (VA60) (-) - z16-3 (VA61) (+) 61 Always 50 kΩ or higher
z16-3 (VA61) (-) - z16-12 (VA62) (+) 62 Always 50 kΩ or higher
z16-12 (VA62) (-) - z16-2 (VA63) (+) 63 Always 50 kΩ or higher
z16-2 (VA63) (-) - z16-11 (VA64) (+) 64 Always 50 kΩ or higher
z17-23 (GA3) (-) - z17-8 (VA65) (+) 65 Always 50 kΩ or higher
z17-8 (VA65) (-) - z17-7 (VA66) (+) 66 Always 50 kΩ or higher
z17-7 (VA66) (-) - z17-22 (VA67) (+) 67 Always 50 kΩ or higher
z17-22 (VA67) (-) - z17-6 (VA68) (+) 68 Always 50 kΩ or higher
z17-6 (VA68) (-) - z17-21 (VA69) (+) 69 Always 50 kΩ or higher
z17-21 (VA69) (-) - z17-20 (VA70) (+) 70 Always 50 kΩ or higher
z17-20 (VA70) (-) - z17-19 (VA71) (+) 71 Always 50 kΩ or higher
z17-19 (VA71) (-) - z17-18 (VA72) (+) 72 Always 50 kΩ or higher
z17-18 (VA72) (-) - z17-17 (VA73) (+) 73 Always 50 kΩ or higher
z17-17 (VA73) (-) - z17-16 (VA74) (+) 74 Always 50 kΩ or higher
z17-16 (VA74) (-) - z17-15 (VA75) (+) 75 Always 50 kΩ or higher
z17-15 (VA75) (-) - z17-14 (VA76) (+) 76 Always 50 kΩ or higher
z17-14 (VA76) (-) - z17-5 (VA77) (+) 77 Always 50 kΩ or higher
z17-5 (VA77) (-) - z17-13 (VA78) (+) 78 Always 50 kΩ or higher
z17-13 (VA78) (-) - z17-4 (VA79) (+) 79 Always 50 kΩ or higher
z17-4 (VA79) (-) - z17-3 (VA80) (+) 80 Always 50 kΩ or higher
z17-3 (VA80) (-) - z17-12 (VA81) (+) 81 Always 50 kΩ or higher
z17-12 (VA81) (-) - z17-2 (VA82) (+) 82 Always 50 kΩ or higher
z17-2 (VA82) (-) - z17-11 (VA83) (+) 83 Always 50 kΩ or higher
z17-11 (VA83) (-) - z17-1 (VA84) (+) 84 Always 50 kΩ or higher


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Read the resistance after the value has stabilized.

·

In order to avoid damaging the terminals of the battery voltage sensor, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of the battery voltage sensor.




Result:
Result Proceed to
The resistance between the terminals is 50 kΩ or higher. A
Other than above B


Post-procedure1

a.

Install the battery voltage sensor (for lower side).

CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When connecting connectors z16 and z17 of the battery voltage sensor (for lower side), first connect connector y3 to the battery voltage sensor (for lower side).




A

10.CHECK TOTAL DISTANCE DRIVEN

B

REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)

10.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

B

11.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
11.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK