Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM
RM37H0E _54 Brake _096946 PARKING BRAKE _0455727 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C113319  Unified Electric Parking Brake Actuator Performance Circuit Current Above Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C113319 Unified Electric Parking Brake Actuator Performance Circuit Current Above Threshold When the electric parking brake is operating, overcurrent is detected in the parking brake actuator assembly with bracket 3 times.
·

Parking brake actuator assembly with bracket

·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


DTC stored Brake/EPB A An electric parking brake system malfunction is displayed on the multi-information display.

CAUTION / NOTICE / HINT

NOTICE:
·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "EPB Initialize" and "Acquire Tension Sensor Zero Point".

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>UTILITY

·

After replacing the parking brake actuator assembly with bracket, perform "EPB Initialize" and "Acquire Tension Sensor Zero Point".

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G71 parking brake actuator assembly with bracket connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6,G71)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assembly

A6-3 (M+) - G71-8 (M+) Always Below 1 Ω
A6-3 (M+) or G71-8 (M+) - Body ground Always 10 kΩ or higher
A6-2 (M-) - G71-7 (M-) Always Below 1 Ω
A6-2 (M-) or G71-7 (M-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET (PARKING BRAKE MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET (PARKING BRAKE MOTOR)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the G71 parking brake actuator assembly with bracket connector.


Procedure1

a.
C139753C09
1.552,0.177 1.927,0.427 0.375,0.25 0.333,1.667 0.333,1.583 0.333,1.583 1.5,1.333 true 2,1.333 3,1.583 3,1.583 3,1.667 true 2.917,1.708 3.24,1.917 0.323,0.208 10 false M+ 0.271,1.719 0.583,1.917 0.313,0.198 10 false M- 0.125,0.146 0.417,0.375 0.292,0.229 10 false *a 1.615,0.229 1.927,0.427 0.313,0.198 10 false G71
*a Component without harness connected
(Parking Brake Actuator Assembly with Bracket)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G71)Location & Routing

Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assembly

G71-7(M-) - G71-8(M+) Always Below 4 Ω
G71-7 (M-) - Body ground Always 10 kΩ or higher
G71-8 (M+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK FOR SHORT TO +B

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET

3.CHECK FOR SHORT TO +B

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the G71 parking brake actuator assembly with bracket connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G71)Location & Routing

Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assembly

G71-8 (M+) - G71-7 (M-) Electric parking brake not operating Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET

NG

4.CHECK FOR SHORT TO +B
4.CHECK FOR SHORT TO +B

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the G71 parking brake actuator assembly with bracket connector.


c.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G71,A6)Location & Routing

Click Connector(G71)Body>Floor Wire / No. 3 Floor Wire>Parking Brake Actuator with Bracket Assembly

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

G71-8 (M+) or A6-3 (M+) - Body ground Always Below 1 V
G71-7 (M-) or A6-2 (M-) - Body ground Always Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR