Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AE411  Hybrid/EV Battery Precharge Contactor Circuit Short to Ground  


DESCRIPTION

The SMRs (System Main Relays) are the relays that connect or disconnect the high-voltage system in accordance with commands from the EV control ECU.

There are 3 SMRs and 1 system main resistor. SMRB, SMRP, SMRG and the system main resistor are located in the No. 1 EV battery junction block assembly.

To connect to the high voltage power system, the vehicle will first turn on SMRP and SMRB to charge the vehicle through the system main resistor. Then, SMRP will be turned off after SMRG is turned on. To shut off the high voltage power system, SMRB and SMRG are turned off.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground Short to ground in the SMRP circuit:
Primary circuit of SMRP is malfunctioning.
(2 trip detection logic)
·

Wire harness or connector

·

No. 1 EV battery junction block assembly

·

EV control ECU


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P0AE411
·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Hybrid/EV Battery Voltage

·

SMRP Status

·

SMRB Status

·

SMRG Status

·

SMRP Control Status

·

SMRB Control Status

·

SMRG Control Status

·

Boosting Converter Shutdown Status

·

Motor Inverter Shutdown Status

·

FC Air Compressor Inverter Shutdown Status



CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

4.

Turn the ignition switch and wait for 10 minutes or more.

5.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the HV battery high-voltage line circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

If DTC P0AE411 is output, the ignition switch cannot be turned to ON (READY).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - BODY GROUND)

Pre-procedure1

a.

Disconnect the G14*1 or A14*2 EV control ECU connector.

*1: for LHD

*2: for RHD


Procedure1

a.
A478492C12
0.396,0.333 0.813,0.615 0.417,0.281 0.396,0.656 0.813,0.938 0.417,0.281 0.823,2.781 0.552,2.302 true 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.469,0.417 0.927,0.615 0.458,0.198 10 false G14 0.844,2.802 1.458,3 0.615,0.198 10 false SMRP 0.469,0.708 0.927,0.906 0.458,0.198 10 false A14 0.906,0.406 1.219,0.604 0.313,0.198 10 false *A 0.917,0.708 1.229,0.906 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G14)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

G14-2 (SMRP) - Body ground Ignition switch off 140 to 290 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A14)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A14-2 (SMRP) - Body ground Ignition switch off 140 to 290 Ω


Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



Post-procedure1

a.

Reconnect the G14*1 or A14*2 EV control ECU connector.

*1: for LHD

*2: for RHD



OK

NG (for LHD)

3.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)

NG (for RHD)

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)
2.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A478500E01
2.021,0.375 2.469,0.698 0.448,0.323 2.135,0.458 2.375,0.604 0.24,0.146 10 true z24

Disconnect the z24 No. 1 EV battery junction block assembly connector.


d.

Disconnect the G14*1 or A14*2 EV control ECU connector.

*1: for LHD

*2: for RHD


Procedure1

a.
A479459C35
2.531,3.51 3.01,3.885 0.479,0.375 0.813,1.479 1.302,1.76 0.49,0.281 0.823,1.844 1.302,2.115 0.479,0.271 1.313,4.302 1.615,3.823 true 0.833,2.333 0.375,1.813 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 0.198,2.76 0.51,2.958 0.313,0.198 10 false *b 2.677,3.615 2.99,3.813 0.313,0.198 10 false z24 0.854,2.365 1.313,2.531 0.458,0.167 10 false SMRP 0.927,4.302 1.469,4.5 0.542,0.198 10 false SMRP 0.927,1.531 1.385,1.729 0.458,0.198 10 false G14 0.917,1.896 1.375,2.094 0.458,0.198 10 false A14 1.385,1.531 1.698,1.729 0.313,0.198 10 false *A 1.385,1.896 1.698,2.094 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to EV Control ECU)
*b Front view of wire harness connector
(to No. 1 EV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G14,z24)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

G14-14 (SMRP) and z24-2 (SMRP) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A14,z24)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

A14-14 (SMRP) and z24-2 (SMRP) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G14*1 or A14*2 EV control ECU connector.

*1: for LHD

*2: for RHD


b.

Reconnect the z24 No. 1 EV battery junction block assembly connector.


c.

Install the No. 10 EV battery shield panel.



OK

REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR