Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  HV Battery High-voltage Line Circuit  


DESCRIPTION

The cause of the malfunction may be the EV supply battery high-voltage line circuit.

Check the continuity in the high-voltage line from the EV supply battery to the inverter.

Check the connection condition and for an open circuit in the frame wire from the service plug grip, EV fuse and EV supply battery to the inverter and perform a function check of the system main relay.

Related Parts Check
Area Inspection
High-voltage circuit from EV supply battery to inverter Check connection condition and for open circuit.
Service plug grip Check connection condition and for open circuit.
EV fuse Check for open circuit.
System Main Relay Check operation condition as relay.

SYSTEM DESCRIPTION

The EV supply battery high voltage is supplied to the inverter via the system main relay operation.

WIRING DIAGRAM

A479477E01
2.99,4.563 3.438,4.76 0.448,0.198 10 false SMRG 3.052,5.969 3.5,6.167 0.448,0.198 10 false SMRP 3.031,1.615 3.479,1.813 0.448,0.198 10 false SMRB 1.688,0.927 2,1.125 0.313,0.198 10 false z13 1.365,1.76 1.677,1.958 0.313,0.198 10 false z19 1.354,2.469 1.667,2.667 0.313,0.198 10 false z18 1.698,3.885 2.01,4.083 0.313,0.198 10 false z12 0.24,1.052 1.219,1.604 0.979,0.552 10 false No. 2 EV Supply Stack Sub-assembly 0.156,2.719 1.094,3.292 0.938,0.573 10 false No. 1 EV Supply Stack Sub-assembly 0.229,3.531 1.063,3.958 0.833,0.427 10 false Service Plug Grip 0.208,2.031 1.146,2.448 0.938,0.417 10 false EV Battery Terminal Block 2.021,0.813 2.25,0.958 0.229,0.146 10 false + 2.031,3.74 2.26,3.885 0.229,0.146 10 false - 1.24,7.375 3.885,7.656 2.646,0.281 10 false : EV Supply Battery Voltage Line 4.083,4.219 4.531,4.417 0.448,0.198 10 false SMRG 4.219,3.74 4.531,3.938 0.313,0.198 10 false CEI 4.083,5.635 4.531,5.833 0.448,0.198 10 false SMRP 4.083,1.271 4.531,1.469 0.448,0.198 10 false SMRB 4.177,6.104 4.49,6.302 0.313,0.198 10 false GND 4.188,0.802 4.5,1 0.313,0.198 10 false CBI 6.479,0.948 6.792,1.146 0.313,0.198 10 false A 6.49,1.802 6.802,2 0.313,0.198 10 false B 4.573,4.323 4.885,4.521 0.313,0.198 10 false z24 6.021,4.844 6.177,5.042 0.156,0.198 10 false C 6.021,5.292 6.177,5.49 0.156,0.198 10 false D 6.031,5.729 6.344,5.927 0.313,0.198 10 false E 4.615,3.896 4.927,4.094 0.313,0.198 10 false N2 4.583,5.74 4.896,5.938 0.313,0.198 10 false z24 4.583,6.198 4.896,6.396 0.313,0.198 10 false z24 4.583,1.375 4.896,1.573 0.313,0.198 10 false z24 4.604,0.938 4.917,1.135 0.313,0.198 10 false N1 4.635,0.75 4.792,0.948 0.156,0.198 10 false 1 4.625,1.188 4.781,1.385 0.156,0.198 10 false 1 4.646,3.708 4.802,3.906 0.156,0.198 10 false 1 4.656,4.156 4.813,4.354 0.156,0.198 10 false 4 4.656,5.573 4.813,5.771 0.156,0.198 10 false 2 4.635,6.031 4.792,6.229 0.156,0.198 10 false 3 1.958,6.729 4.719,6.896 2.76,0.167 10 false No. 1 EV Battery Junction Block Assembly 1.729,0.75 1.885,0.948 0.156,0.198 10 false 1 1.771,3.698 1.927,3.896 0.156,0.198 10 false 1 1.198,1.76 1.354,1.958 0.156,0.198 10 false 1 1.188,2.49 1.344,2.688 0.156,0.198 10 false 1

for LHD:
A484915E01
1.354,0.646 1.667,0.844 0.313,0.198 10 false N3 1.354,1.51 1.667,1.708 0.313,0.198 10 false N3 0.688,0.646 0.885,0.813 0.198,0.167 10 false A 0.688,1.49 0.885,1.656 0.198,0.167 10 false B 1.656,0.656 1.969,0.854 0.313,0.198 10 false CBI 1.656,1.521 1.969,1.719 0.313,0.198 10 false CEI 2.635,0.667 2.781,0.865 0.146,0.198 10 false P 2.635,1.24 2.781,1.438 0.146,0.198 10 false N 2.323,1.885 2.781,2.094 0.458,0.208 10 false C-OFF 2.896,0.635 3.208,0.833 0.313,0.198 10 false x2 2.885,1.25 3.198,1.448 0.313,0.198 10 false x2 2.896,1.865 3.208,2.063 0.313,0.198 10 false x2 5.281,0.656 5.427,0.854 0.146,0.198 10 false P 5.281,1.292 5.427,1.49 0.146,0.198 10 false N 5.281,1.885 5.74,2.094 0.458,0.208 10 false C-OFF 1.406,2.417 3.146,2.729 1.74,0.313 10 false FC Converter Assembly 5.125,2.365 5.438,2.563 0.313,0.198 10 false x1 5.104,2.552 6.552,2.958 1.448,0.406 10 false Inverter with Converter Assembly 0.677,3.99 0.875,4.156 0.198,0.167 10 false C 0.656,4.75 0.854,4.917 0.198,0.167 10 false D 0.667,5.51 0.865,5.677 0.198,0.167 10 false E 1.406,0.448 1.604,0.615 0.198,0.167 10 false 2 1.406,1.313 1.604,1.479 0.198,0.167 10 false 1 2.906,0.469 3.104,0.635 0.198,0.167 10 false 1 2.917,1.073 3.115,1.24 0.198,0.167 10 false 2 2.927,1.688 3.125,1.854 0.198,0.167 10 false 3 5.094,0.51 5.292,0.677 0.198,0.167 10 false 1 5.083,1.104 5.281,1.271 0.198,0.167 10 false 2 5.083,1.771 5.281,1.938 0.198,0.167 10 false 3 1.792,4.104 1.99,4.271 0.198,0.167 10 false 6 1.792,4.854 1.99,5.021 0.198,0.167 10 false 9 1.802,5.635 2,5.802 0.198,0.167 10 false 7 2.521,4.094 2.719,4.26 0.198,0.167 10 false 6 2.51,4.844 2.708,5.01 0.198,0.167 10 false 9 2.51,5.615 2.708,5.781 0.198,0.167 10 false 7 5.094,4.104 5.292,4.271 0.198,0.167 10 false 4 5.083,4.833 5.323,5 0.24,0.167 10 false 2 5.052,5.594 5.375,5.76 0.323,0.167 10 false 14 2.021,6.063 2.5,6.25 0.479,0.188 10 false G156 5.25,6.042 5.729,6.229 0.479,0.188 10 false G14 5.26,6.219 6.896,6.417 1.635,0.198 10 false EV Control ECU 0.646,7.323 1.896,7.74 1.25,0.417 10 false : EV Supply Battery Voltage Line 5.281,3.885 5.854,4.063 0.573,0.177 10 false SMRB 5.323,5.406 5.896,5.583 0.573,0.177 10 false SMRP 5.292,4.635 5.865,4.813 0.573,0.177 10 false SMRG 1.646,6.24 3.052,6.677 1.406,0.438 10 false NO. 2 EV Battery Pack Wire Connector 3.5,7.354 5.135,7.552 1.635,0.198 10 false *: with Monitor Circuit 6.198,3.885 6.396,4.052 0.198,0.167 10 false * 6.208,4.646 6.406,4.813 0.198,0.167 10 false * 6.188,5.438 6.385,5.604 0.198,0.167 10 false * 2.552,7.365 4.188,7.563 1.635,0.198 10 false : Shielded

for RHD:
A479478E01
1.375,0.656 1.688,0.854 0.313,0.198 10 false N3 1.375,1.521 1.688,1.719 0.313,0.198 10 false N3 0.688,0.646 0.885,0.813 0.198,0.167 10 false A 0.688,1.49 0.885,1.656 0.198,0.167 10 false B 1.656,0.656 1.969,0.854 0.313,0.198 10 false CBI 1.656,1.521 1.969,1.719 0.313,0.198 10 false CEI 2.635,0.667 2.781,0.865 0.146,0.198 10 false P 2.635,1.24 2.781,1.438 0.146,0.198 10 false N 2.323,1.885 2.781,2.094 0.458,0.208 10 false C-OFF 2.896,0.656 3.208,0.854 0.313,0.198 10 false x2 2.885,1.271 3.198,1.469 0.313,0.198 10 false x2 2.896,1.885 3.208,2.083 0.313,0.198 10 false x2 5.281,0.656 5.427,0.854 0.146,0.198 10 false P 5.281,1.292 5.427,1.49 0.146,0.198 10 false N 5.281,1.885 5.74,2.094 0.458,0.208 10 false C-OFF 1.406,2.417 3.146,2.729 1.74,0.313 10 false FC Converter Assembly 5.125,2.365 5.438,2.563 0.313,0.198 10 false x1 5.104,2.552 6.552,2.958 1.448,0.406 10 false Inverter with Converter Assembly 0.677,3.99 0.875,4.156 0.198,0.167 10 false C 0.656,4.75 0.854,4.917 0.198,0.167 10 false D 0.667,5.51 0.865,5.677 0.198,0.167 10 false E 1.427,0.458 1.625,0.625 0.198,0.167 10 false 2 1.417,1.323 1.615,1.49 0.198,0.167 10 false 1 2.927,0.479 3.125,0.646 0.198,0.167 10 false 1 2.917,1.094 3.115,1.26 0.198,0.167 10 false 2 2.927,1.708 3.125,1.875 0.198,0.167 10 false 3 5.094,0.51 5.292,0.677 0.198,0.167 10 false 1 5.083,1.104 5.281,1.271 0.198,0.167 10 false 2 5.083,1.771 5.281,1.938 0.198,0.167 10 false 3 1.792,4.104 1.99,4.271 0.198,0.167 10 false 6 1.792,4.854 1.99,5.021 0.198,0.167 10 false 9 1.802,5.635 2,5.802 0.198,0.167 10 false 7 2.521,4.094 2.719,4.26 0.198,0.167 10 false 6 2.51,4.844 2.708,5.01 0.198,0.167 10 false 9 2.51,5.615 2.708,5.781 0.198,0.167 10 false 7 3.458,4.844 3.656,5.01 0.198,0.167 10 false 6 3.469,4.104 3.667,4.271 0.198,0.167 10 false 7 3.469,5.625 3.667,5.792 0.198,0.167 10 false 8 4.177,4.094 4.375,4.26 0.198,0.167 10 false 7 4.177,4.844 4.375,5.01 0.198,0.167 10 false 6 4.177,5.615 4.375,5.781 0.198,0.167 10 false 8 5.094,4.104 5.292,4.271 0.198,0.167 10 false 4 5.094,4.833 5.333,5 0.24,0.167 10 false 2 5.031,5.615 5.271,5.781 0.24,0.167 10 false 14 1.635,6.052 2.115,6.24 0.479,0.188 10 false G156 3.417,6.063 3.896,6.25 0.479,0.188 10 false AG2 5.25,6.042 5.729,6.229 0.479,0.188 10 false A14 5.25,6.219 6.885,6.417 1.635,0.198 10 false EV Control ECU 0.646,7.323 1.948,7.677 1.302,0.354 10 false : EV Supply Battery Voltage Line 5.281,3.885 5.854,4.063 0.573,0.177 10 false SMRB 5.323,5.406 5.896,5.583 0.573,0.177 10 false SMRP 5.292,4.635 5.865,4.813 0.573,0.177 10 false SMRG 3.406,6.229 4.49,6.667 1.083,0.438 10 false NO. 2 Floor Wire Connector 1.635,6.208 2.979,6.635 1.344,0.427 10 false NO. 2 EV Battery Pack Wire Connector 3.5,7.354 5.135,7.552 1.635,0.198 10 false *: with Monitor Circuit 6.198,3.885 6.396,4.052 0.198,0.167 10 false * 6.208,4.646 6.406,4.813 0.198,0.167 10 false * 6.188,5.438 6.385,5.604 0.198,0.167 10 false * 2.552,7.365 4.188,7.563 1.635,0.198 10 false : Shielded

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK INVERTER WITH CONVERTER ASSEMBLY (FC JUNCTION CABLE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483165C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.458 0.313,2.656 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Check that the bolts for the FC junction cable is tightened to the specified torque, the FC junction cable is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)



c.

Disconnect the FC junction cable from the inverter with converter assembly.


Procedure1

a.

Check for arc marks on the terminals for the FC junction cable and inverter with converter assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the FC junction cable.



A

2.CHECK FC CONVERTER ASSEMBLY (FC JUNCTION CABLE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

2.CHECK FC CONVERTER ASSEMBLY (FC JUNCTION CABLE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A484671C01
0,2.438 0.313,2.635 0.313,0.198 10 true *B 0,0 0.313,0.198 0.313,0.198 10 true *A
*A for LHD
*B for RHD


Check that the bolts for the FC junction cable is tightened to the specified torque, the FC junction cable is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)



c.

Disconnect the FC junction cable from the FC converter assembly.


Procedure1

a.

Check for arc marks on the terminals for the FC junction cable and FC converter assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the FC junction cable.



A

3.CHECK FC CONVERTER ASSEMBLY (FLOOR UNDER WIRE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

3.CHECK FC CONVERTER ASSEMBLY (FLOOR UNDER WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A484669C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.479 0.313,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Check that the bolts for the floor under wire is tightened to the specified torque, the floor under wire is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.

Disconnect the floor under wire from the FC converter assembly.


c.

Check for arc marks on the terminals for the floor under wire and FC converter assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the floor under wire.



A

4.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

4.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check the condition of the service plug grip.

OK:

Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.



Result:
Proceed to
OK
NG



OK

5.INSPECT SERVICE PLUG GRIP

NG

5.INSPECT SERVICE PLUG GRIP

OK

6.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (FLOOR UNDER WIRE)

NG

6.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (FLOOR UNDER WIRE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A478504E02
1.375,0.073 1.75,0.333 0.375,0.26 1.865,0.073 2.24,0.333 0.375,0.26 2,0.135 2.313,0.333 0.313,0.198 10 false N1 1.5,0.146 1.813,0.344 0.313,0.198 10 false N2

Check that the floor under wire is connected securely, and there are no contact problems.


d.

Disconnect the floor under wire connectors from the No. 1 EV battery junction block assembly.


Procedure1

a.

Check for arc marks on the terminals of the floor wire and the No. 1 EV battery junction block assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the floor under wire.


b.

Install the No. 10 EV battery shield panel.



A

7.CHECK FC JUNCTION CABLE (FC CONVERTER ASSEMBLY - INVERTER WITH CONVERTER ASSEMBLY)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

7.CHECK FC JUNCTION CABLE (FC CONVERTER ASSEMBLY - INVERTER WITH CONVERTER ASSEMBLY)

OK

8.CHECK FLOOR UNDER WIRE

NG

REPLACE FC JUNCTION CABLE

8.CHECK FLOOR UNDER WIRE

OK

9.CHECK FC CONVERTER ASSEMBLY

NG

9.CHECK FC CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A484669C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.479 0.313,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the floor under wire from the FC converter assembly.


c.
A484671C01
0,2.438 0.313,2.635 0.313,0.198 10 true *B 0,0 0.313,0.198 0.313,0.198 10 true *A
*A for LHD
*B for RHD


Disconnect the FC junction cable from the FC converter assembly.


Procedure1

a.
A481475C02
0.99,0.438 1.406,0.75 0.417,0.313 1.927,0.438 2.344,0.75 0.417,0.313 1.292,1.146 1.49,1.667 true 2.01,1.188 1.896,1.75 true 1.135,1.156 0.865,1.646 true 2.188,1.156 2.406,1.708 true 2.063,0.531 2.281,0.698 0.219,0.167 10 true x2 1.125,0.542 1.354,0.698 0.229,0.156 10 true N3 0.677,1.688 0.958,1.865 0.281,0.177 10 true CBI 1.417,1.688 1.708,1.875 0.292,0.188 10 true CEI 1.833,1.75 2.01,1.958 0.177,0.208 10 true N 2.396,1.74 2.542,1.906 0.146,0.167 10 true P 0.063,0.042 0.292,0.198 0.229,0.156 10 true *a
*a Component without harness connected
(FC Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(N3,x2)Location & Routing

Click Connector(N3)Engine Compartment>Floor Under Wire>FC Converter Assembly

Click Connector(x2)Engine Compartment>FC Junction Cable>FC Converter Assembly

N3-1 (CEI) - x2-2 (N) Ignition switch off Below 1 Ω
N3-2 (CBI) - x2-1 (P) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC junction cable.


b.

Reconnect the floor under wire.



OK

10.CHECK EV BATTERY TERMINAL BLOCK

NG

13.REMOVE FC CONVERTER ASSEMBLY
10.CHECK EV BATTERY TERMINAL BLOCK

OK

11.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

REPLACE EV BATTERY TERMINAL BLOCK

11.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery junction block assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A479455C10
3.208,0.188 3.583,0.417 0.375,0.229 3.802,1 4.177,1.271 0.375,0.271 5.656,0.115 6.042,0.396 0.385,0.281 3.354,0.688 3.052,1 true 3.156,1.427 3.396,1.188 true 3.813,1.427 3.604,1.177 true 6.333,1.094 5.813,0.688 true 0.198,0.146 0.51,0.302 0.313,0.156 10 false *a 3.344,0.24 3.552,0.396 0.208,0.156 10 true N1 2.823,1.031 3.135,1.188 0.313,0.156 10 true CBI 2.917,1.438 3.229,1.594 0.313,0.156 10 true GND 3.688,1.438 4.167,1.625 0.479,0.188 10 true SMRB 3.885,1.052 4.135,1.208 0.25,0.156 10 false z24 5.75,0.188 6.01,0.354 0.26,0.167 10 true z13 6.385,1.073 6.635,1.229 0.25,0.156 10 false +
*a Component without harness connected
(No. 1 EV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z13,N1)Location & Routing

Click Connector(z13)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

Click Connector(N1)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assembly

z13-1 (+) - N1-1 (CBI) Auxiliary battery voltage not applied between terminals z24-1 (SMRB) and z24-3 (GND) 10 kΩ or higher
z13-1 (+) - N1-1 (CBI) Auxiliary battery voltage applied between terminals z24-1 (SMRB) and z24-3 (GND) Below 1 Ω



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z24)Location & Routing

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z24-1 (SMRB) - z24-3 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 EV battery junction block assembly.



OK

12.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRG)

NG

REPLACE NO. 1 EV EV BATTERY JUNCTION BLOCK ASSEMBLY

12.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRG)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.

Remove the No. 1 EV battery junction block assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL



b.

Measure the resistance according to the value(s) in the table below.

A479455C11
1.177,0.115 1.552,0.396 0.375,0.281 3.802,0.979 4.177,1.25 0.375,0.271 2.25,0.115 2.604,0.385 0.354,0.271 2.396,0.688 2.115,1.052 true 3.104,1.396 3.292,1.177 true 3.656,1.385 3.417,1.188 true 0.802,1.01 1.313,0.667 true 0.198,0.146 0.51,0.302 0.313,0.156 10 false *a 1.26,0.188 1.51,0.365 0.25,0.177 10 true z12 1.917,1.073 2.281,1.25 0.365,0.177 10 true CEI 3.615,1.438 3.979,1.667 0.365,0.229 10 true GND 2.844,1.438 3.354,1.656 0.51,0.219 10 true SMRG 3.896,1.031 4.146,1.188 0.25,0.156 10 false z24 0.729,0.99 0.979,1.146 0.25,0.156 10 false - 2.354,0.188 2.552,0.354 0.198,0.167 10 true N2
*a Component without harness connected
(No. 1 EV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z12,N2)Location & Routing

Click Connector(z12)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

Click Connector(N2)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assembly

z12-1 (-) - N2-1 (CEI) Auxiliary battery voltage not applied between terminals e2-4 (SMRG) and e2-3 (GND) 10 kΩ or higher
z12-1 (-) - N2-1 (CEI) Auxiliary battery voltage applied between terminals e2-4 (SMRG) and e2-3 (GND) Below 1 Ω



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z24)Location & Routing

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z24-4 (SMRG) - z24-3 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 EV battery junction block assembly.



OK

HV BATTERY HIGH-VOLTAGE LINE CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

13.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

REPLACE FC INVERTER INPUT TERMINAL