Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P310715  Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

Refer to the description for DTC P310711.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P310711

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P310715 Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open Open or short to +B in the communication circuit
(1 trip detection logic)
·

Wire harness or connector

·

Airbag ECU assembly

·

EV control ECU


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P310715 Collision Signal (Airbag)

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 15 seconds or more.

2.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

3.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P310711.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P310711

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK AIRBAG ECU ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG ECU ASSEMBLY (CHECK WAVEFORM)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P310711

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B



A

3.CLEAR DTC

B

6.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (EV)
4.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
result Proceed to
P310715 is not output A
P310715 is output B



Post-procedure1

a.

Turn the ignition switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG ECU ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG ECU ASSEMBLY CONNECTOR)
a.
C374925C33
0.146,0.156 0.458,0.354 0.313,0.198 10 false *a
*a Component with harness connected
(Airbag ECU Assembly)


Check the connector connections and contact pressure of the relevant terminals for the airbag ECU assembly connector.

OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - AIRBAG ECU ASSEMBLY)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - AIRBAG ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the airbag ECU assembly connector.


Procedure1

a.
A481523C05
1.844,1.99 2.281,2.385 0.438,0.396 0.438,3.417 0.885,3.792 0.448,0.375 1.844,1.542 2.281,1.938 0.438,0.396 3.063,2.719 2.896,2.063 true 2.521,4.135 1.823,3.792 true 2.323,1.688 2.781,1.885 0.458,0.198 10 false *A 0.25,0.198 0.563,0.396 0.313,0.198 10 false *a 0.302,2.563 0.615,2.76 0.313,0.198 10 false *b 2.917,2.781 3.375,3.073 0.458,0.292 10 false ABFS 2.615,4.115 3.073,4.406 0.458,0.292 10 false GSW2 0.552,3.521 1.01,3.719 0.458,0.198 10 false D10 1.948,2.104 2.406,2.302 0.458,0.198 10 false D15 1.99,1.667 2.448,1.865 0.458,0.198 10 false A8 2.344,2.125 2.802,2.323 0.458,0.198 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to EV Control ECU)
*b Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-22 (ABFS) - Body ground Ignition switch ON Below 1 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D15-22 (ABFS) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the airbag ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Turn the ignition switch off.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A8,D10)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

A8-22 (ABFS) - D10-24 (GSW2) Ignition switch off Below 1 Ω
A8-22 (ABFS) or D10-14 (GSW2) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G15,D10)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

G15-22 (ABFS) - D10-24 (GSW2) Ignition switch off Below 1 Ω
G15-22 (ABFS) or D10-14 (GSW2) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the airbag ECU assembly connector.


b.

Reconnect the EV control ECU connector.



OK

9.CHECK EV CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK EV CONTROL ECU

Pre-procedure1

a.

Disconnect the airbag ECU assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.
A478491C54
2.563,0.448 3.021,0.813 0.458,0.365 2.563,0.865 3.021,1.229 0.458,0.365 2.854,1.833 3.031,2.427 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.677,0.969 3.198,1.167 0.521,0.198 10 false G15 2.865,2.479 3.365,2.646 0.5,0.167 10 false ABFS 2.708,0.573 3.094,0.781 0.385,0.208 10 false A8 3.063,0.563 3.281,0.781 0.219,0.219 10 false *A 3.083,0.979 3.302,1.177 0.219,0.198 10 false *B
*A for LHD
*B for RHD
*a Component with harness connected
(EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-22 (ABFS) - Body ground Ignition switch ON 11 to 14 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-22 (ABFS) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Turning the ignition switch to ON with the airbag ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the airbag ECU assembly connector.



OK

NG