Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0455055 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  PTC Heater Circuit  


DESCRIPTION

The air conditioning amplifier assembly sends operation signals to the PTC heater relays when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC heater relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.

Symptom Factor
Heating performance is poor when it is cold.
·

No. 1 semiconductor power integration ECU malfunction

·

Quick heater assembly malfunction

·

Air conditioning amplifier assembly malfunction

·

Main body ECU (multiplex network body ECU) malfunction

·

Harness or connector



WIRING DIAGRAM

E366623E07
2.615,1.594 4.302,1.99 1.688,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 0.25,1.583 1.823,1.958 1.573,0.375 10 false Air Conditioning Amplifier Assembly 2.948,3.552 4.594,3.771 1.646,0.219 10 false Quick Heater Assembly 5.385,4.208 7.115,4.615 1.729,0.406 10 false No. 1 Semiconductor Power Integration ECU 6.313,3.115 6.792,3.302 0.479,0.188 10 false CPU 5.667,3 6.938,3.219 1.271,0.219 10 false IPD 5.375,2.615 6.646,2.833 1.271,0.219 10 false L 5.396,3.073 6.667,3.292 1.271,0.219 10 false L 5.135,2.604 6.406,2.823 1.271,0.219 10 false 1 5.135,3.073 6.406,3.292 1.271,0.219 10 false 2 5.375,4.052 6.646,4.271 1.271,0.219 10 false D123 4.271,2.74 4.781,2.948 0.51,0.208 10 false D76 4.344,2.479 4.854,2.688 0.51,0.208 10 false 2 4.271,3.208 4.781,3.417 0.51,0.208 10 false D75 4.354,2.969 4.865,3.177 0.51,0.208 10 false 2 2.833,2.729 3.344,2.938 0.51,0.208 10 false D76 2.906,2.49 3.417,2.698 0.51,0.208 10 false 1 2.844,3.208 3.354,3.417 0.51,0.208 10 false D75 2.906,2.969 3.417,3.177 0.51,0.208 10 false 1 0.74,3.969 2.917,4.167 2.177,0.198 10 false : CXPI Communication System 0.75,4.354 2.771,4.604 2.021,0.25 10 false : CAN Communication System 3.958,2.729 4.469,2.938 0.51,0.208 10 false B 3.979,3.208 4.49,3.417 0.51,0.208 10 false B 3.292,2.729 3.802,2.938 0.51,0.208 10 false E 3.281,3.208 3.792,3.417 0.51,0.208 10 false E

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

OK:

CAN communication system DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.CHECK CXPI COMMUNICATION SYSTEM

NG

2.CHECK CXPI COMMUNICATION SYSTEM
a.

Using the GTS, check if the CXPI communication system is functioning normally.

OK:

CXPI communication system DTCs are not output.



Result:
Proceed to
OK
NG



OK

3.CHECK POWER INTEGRATION SYSTEM

NG

3.CHECK POWER INTEGRATION SYSTEM
a.

Using the GTS, check if the power integration system is functioning normally.

OK:

Power integration system DTCs are not output.



Result:
Proceed to
OK
NG



OK

4.CHECK QUICK HEATER ASSEMBLY

NG

4.CHECK QUICK HEATER ASSEMBLY
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Heater Active Level Quick heater assembly Min.: 0
Max.: 2
Perform this test when the following conditions are met:
·

Ignition switch ON (READY)

·

Air conditioning system is operated


Body Electrical > Air Conditioner > Active Test
Tester Display
Heater Active Level
50004 121 33

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D75,D76)Location & Routing

Click Connector(D75)Instrument Panel>Instrument Panel Wire>Quick Heater Assembly

Click Connector(D76)Instrument Panel>Instrument Panel Wire>Quick Heater Assembly

D75-2 (B) - Body ground
·

Perform Active Test and select "OFF" → "ON" item

·

Heater level is 1


Below 1 V → 11 to 14 V
D76-2 (B) - Body ground
·

Perform Active Test and select "OFF" → "ON" item

·

Heater level is 2


Below 1 V → 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - BODY GROUND)

NG

7.READ VALUE USING GTS (STATUS OF PTC HEATER NO.1 FUSE, STATUS OF PTC HEATER NO.2 FUSE)
5.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - BODY GROUND)
a.

Disconnect the quick heater assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D75,D76)Location & Routing

Click Connector(D75)Instrument Panel>Instrument Panel Wire>Quick Heater Assembly

Click Connector(D76)Instrument Panel>Instrument Panel Wire>Quick Heater Assembly

D75-1 (E) - Body ground Always Below 1 Ω
D76-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT QUICK HEATER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT QUICK HEATER ASSEMBLY
a.
E241121C10
0.927,0.26 1.427,0.51 0.5,0.25 1.927,0.25 2.427,0.5 0.5,0.25 1.271,1.333 1.094,2 1.094,2 0.844,2 true 2.073,1.313 2.323,2 2.323,2 2.573,2 true 2.333,1.25 2.833,1.25 true 0.5,1.25 1,1.25 true 0.375,1.177 0.531,1.323 0.156,0.146 10 false B 0.729,1.938 0.906,2.115 0.177,0.177 10 false E 2.625,1.917 2.823,2.073 0.198,0.156 10 false B 2.896,1.156 2.99,1.313 0.094,0.156 10 false E 2.135,0.313 2.229,0.469 0.094,0.156 10 false B 1.156,0.302 1.25,0.458 0.094,0.156 10 false A 0.104,0.073 0.542,0.281 0.438,0.208 10 false *a
*a Component without harness connected
(Quick Heater Assembly)


Disconnect the D75 and D76 quick heater assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (B) - A-1 (E) Always Below 10 kΩ
B-2 (B) - B-1 (E) Always Below 10 kΩ



Result:
Proceed to
OK
NG



OK

NG

7.READ VALUE USING GTS (STATUS OF PTC HEATER NO.1 FUSE, STATUS OF PTC HEATER NO.2 FUSE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Status of PTC Heater No.1 Fuse Quick heater assembly fuse Connect or Disconnect Connect: Fuse not shut off
Disconnect: Fuse shut off
-
Status of PTC Heater No.2 Fuse Quick heater assembly fuse Connect or Disconnect Connect: Fuse not shut off
Disconnect: Fuse shut off
-
Body Electrical > Power Integration No.2 > Data List
Tester Display
Status of PTC Heater No.1 Fuse
Status of PTC Heater No.2 Fuse
50003 411 62,63
OK:

The Data List value displays "Connect".



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPLACE NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU AND QUICK HEATER ASSEMBLY