Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1DC500  FC Air Pressure Too High  


DESCRIPTION

The air system of the FC system feeds the FC stack with oxygen, so that the FC stack can generate power.

In order to feed the FC stack with air volume and pressure that are needed for FC stack power generation, the air system regulates the FC air pressure regulator assembly (air pressure regulating valve), FC air by-pass valve assembly (air shunt valve) and FC air compressor with motor assembly based the sensor inputs.

If the air pressure (air pressure sensor measurement) is likely to exceed the FC stack pressure limitation, the EV control ECU interprets that the air pressure is excessively high, and stores this DTC.

For the circuit diagram, refer to DTC P1DDF00.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1DDF00

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1DC500 FC Air Pressure Too High
·

FC Stack Air Pressure (FC Stack Inlet) is likely to exceed the FC stack pressure limitation.

This malfunction detection is active while the FC system is in modes other than FC Shutdown.

·

The operating point of the FC air compressor assembly with motor is estimated to continue to be in the surge range during high pressure, or a surge state is detected


(1 trip detection logic)
·

All air system piping (includes exhaust drainage pipes)

·

FC stack assembly

·

FC air compressor with motor assembly

·

FC stack inlet air pressure sensor (vacuum sensor assembly)

·

Mass air flow meter sub-assembly

·

FC air pressure regulator assembly (air sealing valve)

·

FC air by-pass valve assembly (air shunt valve)

·

FC air pressure regulator assembly (air pressure regulating valve)

·

Amount of FC stack coolant

·

FC stack coolant piping (leakage)


Master Warning: Comes on EV B

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection - ○ ○ ○ ○ ○

Related Data List
DTC No. Data List
P1DC500
·

Atmospheric Pressure

·

Intake Air Temperature (Filtered Value)

·

Target Mass Air Flow

·

Mass Air Flow (Filtered Value)

·

FC Air Compressor Motor Speed

·

Target FC Air Compressor Motor Speed

·

Target FC Inlet Air Pressure

·

FC Inlet Air Pressure (Filtered Value)

·

FC Air Compressor Consumption Power



Related Active Test
DTC No. Active Test
P1DC500 Control the FC Air Compressor

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle for 10 minutes according to the freeze frame data (Vehicle Speed, Accelerator Degree, etc.).

Since malfunction detection is performed when a high load is applied, drive the vehicle under high load conditions, such as driving uphill. It is important that the vehicle speed is close to a speed recorded in the freeze frame data as much as possible. The "FC Inlet Air Pressure (Filtered Value)" is roughly less than 130 kPa(abs) during light load operation including idling.

CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.




PROCEDURE

1.CHECK DTC OUTPUT
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


Pre-procedure1

a.

None


Procedure1

a.

According to the display on the GTS, check for DTCs in the Health Check.

Result:
Result Proceed to
Only P1DC500 is output A
P1DC500 is output and DTCs other than the DTCs in the table below are output B
P1DC500 is output and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1DC618 (FC) Air Sealing Valve Circuit Current Below Threshold
P1DC619 (FC) Air Sealing Valve Circuit Current Above Threshold
P1DC711 (FC) Air Sealing Valve Position Sensor Circuit Short to Ground
P1DC715 (FC) Air Sealing Valve Position Sensor Circuit Short to Battery or Open
P1E7A18 (FC) Air Shunt Valve Circuit Current Below Threshold
P1E7A19 (FC) Air Shunt Valve Circuit Current Above Threshold
P1E7B11 (FC) Air Shunt Valve Position Sensor Circuit Short to Ground
P1E7B15 (FC) Air Shunt Valve Position Sensor Circuit Short to Battery or Open
P1E7C18 (FC) Air Pressure Regulating Valve Circuit Current Below Threshold
P1E7C19 (FC) Air Pressure Regulating Valve Circuit Current Above Threshold
P1E7D11 (FC) Air Pressure Regulating Valve Position Sensor Circuit Short to Ground
P1E7D15 (FC) Air Pressure Regulating Valve Position Sensor Circuit Short to Battery or Open
System malfunction P009A62 (EV) Intake Air Temperature/Ambient Air Temperature Correlation Signal Compare Failure
P1D7F62 (EV) FC Air Compressor Motor Signal Compare Failure
P1D7F96 (EV) FC Air Compressor Motor Component Internal Failure
P1DDF00 (EV) FC Air Flow Malfunction
P1DDF79 (EV) FC Air Flow Mechanical Linkage Failure
P1F6C71 (EV) Air Sealing Valve Actuator Stuck
P1F6D71 (EV) Air Shunt Valve Actuator Stuck
P1F6E71 (EV) Air Pressure Regulating Valve Actuator Stuck


HINT:

DTC P1DC500 may be store due to problems that cause the DTCs shown above to be output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order of the listed DTCs shown in the table above.



Post-procedure1

a.

Turn the ignition switch off.



A

2.READ VALUE USING GTS (FC INLET AIR PRESSURE (FILTERED VALUE))

B

2.READ VALUE USING GTS (FC INLET AIR PRESSURE (FILTERED VALUE))

C

GO TO DTC CHART

2.READ VALUE USING GTS (FC INLET AIR PRESSURE (FILTERED VALUE))

Pre-procedure1

a.

None


Procedure1

a.

Turn the ignition switch to ON.


b.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
FC Inlet Air Pressure (Filtered Value)
50003 397 891

c.

Using the table, read the normal atmospheric pressure value for the applicable altitude.

A479641C01
0.177,0.063 0.49,0.26 0.313,0.198 10 false *a 0.396,0.51 0.708,0.708 0.313,0.198 10 false *b 2.719,0.51 3.031,0.708 0.313,0.198 10 false *b 5.031,0.51 5.344,0.708 0.313,0.198 10 false *b 1.146,0.51 1.458,0.708 0.313,0.198 10 false *c 3.438,0.5 3.75,0.698 0.313,0.198 10 false *c 5.729,0.5 6.042,0.698 0.313,0.198 10 false *c 1.802,0.5 2.115,0.698 0.313,0.198 10 false *d 4.125,0.51 4.438,0.708 0.313,0.198 10 false *d 6.396,0.521 6.708,0.719 0.313,0.198 10 false *d
*a Altitude, Temperature and Atmospheric Pressure Correlation Table *b Altitude (m (ft.))
*c Temperature (°C (°F)) *d Atmospheric Pressure (kPa (psi))


HINT:
·

Standard atmospheric pressure is approximately 101 kPa (15 psi).

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (0.1 psi). This varies by weather.




d.

Compare the "FC Inlet Air Pressure (Filtered Value)" values in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Difference between "FC Inlet Air Pressure (Filtered Value)" in Data List and normal atmospheric pressure value is 10 kPa or more. A
Other than above. B



Post-procedure1

a.

Turn the ignition switch off.



B

3.CHECK INTAKE AND EXHAUST PIPING

A

REPLACE VACUUM SENSOR ASSEMBLY

3.CHECK INTAKE AND EXHAUST PIPING
a.

Check that no air comes in without flowing through each part of the intake air system and the exhaust drainage pipe is not clogged, disconnected, or damaged.

HINT:

Check the area extending from the FC air compressor assembly with motor to the exhaust drainage pipe.


OK:

The intake and exhaust piping is not clogged, disconnected or damaged



Result:
Proceed to
OK
NG



OK

4.CHECK FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

4.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None


Procedure1

a.

Read the freeze frame data of DTC P1DC500.

Powertrain > EV > DTC(P1DC500) > Freeze Frame Data
Tester Display
FC Inlet Air Pressure (Filtered Value)
50040 397 891 P1DC500
Result:
Result Proceed to
The value of FC Inlet Air Pressure (Filtered Value) is 303 kPa(abs) or more A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

10.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE)

B

5.CHECK COOLANT (FC STACK COOLANT) LEAK
5.CHECK COOLANT (FC STACK COOLANT) LEAK

Pre-procedure1

a.

Check the FC stack coolant level in the FC radiator reserve tank.


Procedure1

a.

Check for FC coolant leaks.

Click hereEngine / Hybrid System>COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION

Result:
Result Proceed to
No leaks are found and the FC coolant level in the FC radiator reserve tank is above the low line. A
No leaks are found and the FC coolant level in the FC radiator reserve tank is below the low line. B
FC coolant leaks are evident. C


HINT:
·

After repairing the FC coolant leaks and adding coolant, perform the "Control the FC Coolant Pump" and "Control the Radiator Fan 1" Active Test and make sure that there are no malfunctions.

·

If a coolant leak cannot be found despite that the coolant in the radiator reserve tank is below the Low level, leakage may have occurred inside the FC stack or in the air conditioning system.

·

If there is a leak in the FC stack, DTC P0AA649 may be output to the EV control ECU.




Post-procedure1

a.

None



A

6.CHECK COOLANT HOSE

B

13.ADD FC STACK COOLANT

C

INSPECT COOLANT LEAK AND ADD COOLANT

6.CHECK COOLANT HOSE
a.

Check that the cooling system hoses are not kinked or clogged.

OK:

The cooling system hoses are not kinked or clogged



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)

NG

REPAIR OR REPLACE COOLANT HOSE

7.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)

Pre-procedure1

a.

None


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Atmospheric Pressure
50003 397 888

b.

Using the table, read the normal atmospheric pressure value for the applicable altitude.

A479641C01
0.177,0.063 0.49,0.26 0.313,0.198 10 false *a 0.396,0.51 0.708,0.708 0.313,0.198 10 false *b 2.719,0.51 3.031,0.708 0.313,0.198 10 false *b 5.031,0.51 5.344,0.708 0.313,0.198 10 false *b 1.146,0.51 1.458,0.708 0.313,0.198 10 false *c 3.438,0.5 3.75,0.698 0.313,0.198 10 false *c 5.729,0.5 6.042,0.698 0.313,0.198 10 false *c 1.802,0.5 2.115,0.698 0.313,0.198 10 false *d 4.125,0.51 4.438,0.708 0.313,0.198 10 false *d 6.396,0.521 6.708,0.719 0.313,0.198 10 false *d
*a Altitude, Temperature and Atmospheric Pressure Correlation Table *b Altitude (m (ft.))
*c Temperature (°C (°F)) *d Atmospheric Pressure (kPa (psi))


HINT:
·

Standard atmospheric pressure is approximately 101 kPa (15 psi).

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (0.1 psi). This varies by weather.




c.

Compare the "Atmospheric Pressure" values in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Difference between "Atmospheric Pressure" in Data List and normal atmospheric pressure value is 10 kPa or more. A
Other than above. B



Post-procedure1

a.

Turn the ignition switch off.



B

8.READ VALUE USING GTS (MASS AIR FLOW (FILTERED VALUE))

A

8.READ VALUE USING GTS (MASS AIR FLOW (FILTERED VALUE))

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Mass Air Flow (Filtered Value)
50003 397 897
Result:
Result Proceed to
The value of Mass Air Flow (Filtered Value) is less than 8 L/min A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

9.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)

B

REPLACE INTAKE MASS AIR FLOW METER SUB-ASSEMBLY

9.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)

OK

10.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE)

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

10.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE)

Pre-procedure1

a.

Remove the FC air pressure regulator assembly (air sealing valve).

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR CONTROL VALVE>REMOVAL



Procedure1

a.

Visually check the FC air pressure regulator assembly (air sealing valve).

OK:

The valve shaft is not bent or otherwise damaged



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the FC air pressure regulator assembly (air sealing valve).



OK

11.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE)

NG

REPLACE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE)

11.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE)

Pre-procedure1

a.

Remove the FC air pressure regulator assembly (air pressure regulating valve).

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR CONTROL VALVE>REMOVAL



Procedure1

a.

Visually check the FC air pressure regulator assembly (air pressure regulating valve).

OK:

The valve shaft is not bent or otherwise damaged



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the FC air pressure regulator assembly (air pressure regulating valve).



OK

12.CHECK FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE)

NG

REPLACE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE)

12.CHECK FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE)

Pre-procedure1

a.

Remove the FC air by-pass valve assembly (air shunt valve).

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR BYPASS VALVE>REMOVAL



Procedure1

a.

Visually check the FC air by-pass valve assembly (air shunt valve).

OK:

The valve shaft is not bent or otherwise damaged



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the FC air by-pass valve assembly (air shunt valve).



OK

NG

REPLACE FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE)

13.ADD FC STACK COOLANT

Pre-procedure1

a.

None


b.

Add FC stack coolant and bleed air.


Procedure1

a.

After bleeding air, check the coolant level and check for coolant leaks again.

OK:

No leaks are found and the FC coolant level in the FC radiator reserve tank is above the low line.


HINT:
·

After repairing the FC coolant leaks and adding coolant, perform the "Control the FC Coolant Pump" and "Control the Radiator Fan 1" Active Test and make sure that there are no malfunctions.

·

If a coolant leak cannot be found despite that the coolant in the radiator reserve tank is below the Low level, leakage may have occurred inside the FC stack or in the air conditioning system.

In this case, add coolant and then bleed air from the coolant. If the coolant level is still too low but a coolant leak cannot be confirmed even in the air conditioning system, the coolant leak is in the FC stack. Replace the FC stack.

·

If there is a leak in the FC stack, DTC P0AA649 may be output to the EV control ECU.



Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

END

NG

REPLACE FC STACK ASSEMBLY