Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1E447A  Hydrogen Leak (Low Pressure Area) Fluid Leak or Seal Failure  


DESCRIPTION

The hydrogen system of the FC system feeds the FC stack with hydrogen, so that the FC stack can generate power.

The low-range pressure line located after the hydrogen injectors are called a hydrogen circulation system line, and its internal pressure is properly regulated by the hydrogen injectors for FC stack power generation.

Pressures in the low-range pressure line is monitored by the system, and if the internal pressure decreases despite the hydrogen injectors and exhaust drainage valve being closed, this will be interpreted as external leaks, and this DTC will be stored.

For the circuit diagram, refer to DTC P1DC000.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1DC000

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1E447A Hydrogen Leak (Low Pressure Area) Fluid Leak or Seal Failure Following malfunction detection is active while the mode is in FC Startup Process or Working (FC Intermittent Operation).
Hydrogen injectors and exhaust drainage valve are forced to close to shut off the hydrogen circulation system line (low-range pressure system) for checking if a pressure decrease has occurred in the system line so as to detect hydrogen leakage.
(1 trip detection logic)
·

Exhaust drainage valve

·

Low-range hydrogen pressure pipe

·

Hydrogen secondary pressure sensor

·

FC stack assembly

·

Sealed area of each component


Master Warning: Comes on EV B

HINT:

This DTC indicates leaks from the low-range hydrogen pressure system located after the hydrogen injectors.


Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection - ○ ○ - - -

Related Data List
DTC No. Data List
P1E447A
·

Tank Shut Valve 1 Drive Status

·

Tank Shut Valve 2 Drive Status

·

Tank Shut Valve 3 Drive Status

·

Hydrogen Injector 1 Injection Period

·

Hydrogen Injector 2 Injection Period

·

Hydrogen Injector 3 Injection Period

·

Target Low-Range Hydrogen Pressure

·

High-Range Hydrogen Pressure (Filtered Value)

·

Medium-Range Hydrogen Pressure (Filtered Value)

·

Low-Range Hydrogen Pressure (Filtered Value)

·

Motor Room Hydrogen Density

·

Tank Area 1 Hydrogen Density

·

Tank Area 2 Hydrogen Density

·

Exhaust Drainage Valve



Related Active Test
DTC No. Active Test
P1E447A Control the Select Hydrogen Injector

CAUTION / NOTICE / HINT

CAUTION:
·
A341072

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.

Click hereEngine / Hybrid System>FUEL>FUEL SYSTEM>PRECAUTION



NOTICE:
·

After completion of repair, check that no hydrogen leaks from the hydrogen pipes using a hydrogen gas detector.

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:
·

Forcing the SOC of the EV supply battery assembly to decrease by applying electrical loads such as turning on the air conditioning (HOT MAX, maximum airflow), or depressing the accelerator pedal with the shift state in park (P), the "FC Intermittent Operation" of the Data List is easily to enter OFF (power generation mode).


After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Working. Then, wait for 2 minutes or more (If FC system cannot be activated, check the DTCs that are present at the time).

2.

Turn the ignition switch off and wait for 10 minutes or more.



PROCEDURE

1.CHECK DTC OUTPUT
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


Pre-procedure1

a.

None


Procedure1

a.

According to the display on the GTS, check for DTCs in the Health Check.

Result:
Result Proceed to
Only P1E447A is output A
P1E447A is output and DTCs other than the DTCs in the table below are output B
P1E447A is output and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1D9A1C (FC) Hydrogen Injector 1 Circuit Voltage Out of Range
P1DA01C (FC) Hydrogen Injector 2 Circuit Voltage Out of Range
P1DA51C (FC) Hydrogen Injector 3 Circuit Voltage Out of Range
P1DAA12 (FC) Exhaust Drainage Valve Circuit Short to Battery
P1DAA14 (FC) Exhaust Drainage Valve Circuit Short to Ground or Open
P1DBA11 (FC) Low-Range Hydrogen Pressure Sensor Circuit Short to Ground
P1DBA15 (FC) Low-Range Hydrogen Pressure Sensor Circuit Short to Battery or Open


HINT:

DTC P1E447A may be store due to problems that cause the DTCs shown above to output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order of the listed DTCs shown in the table above.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CLEAR DTC

B

2.CLEAR DTC

C

GO TO DTC CHART

2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

3.CHECK HYDROGEN GAS LEAK
3.CHECK HYDROGEN GAS LEAK
CAUTION:
·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.

·

Open the hood with the ignition switch off, check for hydrogen leaks around the underbody and in the motor compartment with a hydrogen gas detector. If leakage is found, pay extra attention to fire safety in the following operations.



HINT:

For procedures to check for leaks from hydrogen pipes and components (high-range pressure and medium-range pressure), refer toEngine / Hybrid System>FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION.


Pre-procedure1

a.

Turn the ignition switch off.


b.

Remove the under cover.


Procedure1

a.

Check that the hydrogen tank and hydrogen pipes are not damaged.


b.

Check for a gas leaking sound, and then check if there are hydrogen leaks in the hydrogen pipes and components with a hydrogen gas detector.

A477015C02
6.219,3.813 6.031,3.052 true 6.469,3.281 6.469,2.99 true 4.01,2.719 4.219,2.635 true 4.688,1.406 5.104,0.698 true 5.646,3.49 5.729,2.813 true 6.635,1.833 6.729,1.135 true 4.969,2.323 5.563,2.177 true 4.917,2.146 5.26,2.042 true 4.969,2.469 5.323,2.396 true 2.552,2.135 2.844,1.667 true 4.906,2.031 5.479,1.729 true 2.698,3.563 3.188,2.792 true 1.292,2.104 1.979,1.5 true 0.531,1.885 0.24,0.927 true 4.49,3.708 4.396,3.313 true 6.406,2.865 6.146,2.25 true 4.208,2.177 4.01,1.781 true 4.906,3.885 4.854,3.26 true 5.021,3.052 5.469,3.979 true 0.99,1.854 1.313,1.115 true 6.24,4.01 6.448,4.198 0.208,0.188 10 false *1 5.563,3.563 5.802,3.729 0.24,0.167 10 false *2 5.281,1.969 5.594,2.125 0.313,0.156 10 false *3 5.51,1.635 5.823,1.792 0.313,0.156 10 false *5 2.865,1.51 3.177,1.667 0.313,0.156 10 false *6 1.302,0.979 1.615,1.135 0.313,0.156 10 false *14 6.667,0.958 6.979,1.115 0.313,0.156 10 false *8 6.042,2.063 6.354,2.219 0.313,0.156 10 false *9 5.427,4.021 5.896,4.177 0.469,0.156 10 false *10 2.583,3.583 3.052,3.74 0.469,0.156 10 false *11 2.01,1.375 2.281,1.531 0.271,0.156 10 false *12 0.708,3.26 1.021,3.417 0.313,0.156 10 false : *a 0.719,3.49 1.031,3.646 0.313,0.156 10 false : *b 0.729,3.75 1.042,3.906 0.313,0.156 10 false : *c 0.75,4.01 1.063,4.167 0.313,0.156 10 false : *d 3.823,2.698 4.063,2.865 0.24,0.167 10 false *2 5.375,2.323 5.688,2.479 0.313,0.156 10 false *3 5.177,0.604 5.49,0.76 0.313,0.156 10 false *7 4.781,2.99 5.25,3.146 0.469,0.156 10 false *10 6.406,3.323 6.646,3.49 0.24,0.167 10 false *2 4.385,3.781 4.625,3.948 0.24,0.167 10 false *2 5.615,2.094 5.927,2.25 0.313,0.156 10 false *4 3.885,1.542 4.198,1.698 0.313,0.156 10 false *9 4.844,3.938 5.156,4.094 0.313,0.156 10 false *9 0.115,0.76 0.385,0.917 0.271,0.156 10 false *13
*1 Hydrogen Inlet Receptacle Assembly *2 High-range Hydrogen Pressure Pipe (for filling)
*3 Hydrogen Tank Tube Joint *4 Hydrogen Tank Pressure Sensor (for Inlet Side)
*5 Hydrogen Tank Pressure Sensor (for Outlet Side) *6 No. 1 Hydrogen Tank Assembly
*7 No. 2 Hydrogen Tank Assembly *8 No. 3 Hydrogen Tank Assembly
*9 High-range Hydrogen Pressure Pipe (for feeding) *10 Hydrogen Supply Regulator Assembly
*11 Medium-range Hydrogen Pressure Pipe *12 Low-range Hydrogen Pressure Pipe
*13 FC Stack Assembly *14 Hydrogen Injector
*a High-range Pressure Area (when filling)
(Hydrogen Inlet Receptacle Assembly → Hydrogen Tank Assembly )
*b High-range Pressure Area
(Hydrogen Tank Assembly → Hydrogen Supply Regulator Assembly)
*c Medium-range Pressure Area
(Hydrogen Supply Regulator Assembly → Hydrogen Injector)
*d Low-range Pressure Area
(Hydrogen Injector → FC Stack)



Standard value:

300 ppm or less. (Hydrogen gas detector)


Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the under cover.



OK

4.CHECK HYDROGEN GAS LEAK

NG

7.CHECK HYDROGEN GAS LEAKAGE POINT
4.CHECK HYDROGEN GAS LEAK
CAUTION:
·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.

·

Open the hood with the ignition switch off, check for hydrogen leaks around the underbody and in the motor compartment with a hydrogen gas detector. If leakage is found, pay extra attention to fire safety in the following operations.



NOTICE:

Turn the ignition switch to ON (READY) causes the tank shut valve to open, and this pressurizes hydrogen in the hydrogen pipes. At this time, locate leaking areas of the hydrogen pipe. If there are leaks, the hydrogen pressure in the pipe decreases gradually, so perform checks quickly.


HINT:

For procedures to check for leaks from hydrogen pipes and components (high-range pressure and medium-range pressure), refer toEngine / Hybrid System>FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION.


Pre-procedure1

a.

Remove the under cover.


b.

Turn the ignition switch to ON (READY) with the shift lever in P, and check that the Data List "FC Work Mode" is Working and "FC Intermittent Operation" is OFF.

Powertrain > EV > Data List
Tester Display
FC Work Mode
FC Intermittent Operation
50003 397 962,872
HINT:

If there are no leaks, the high-range and medium-range hydrogen systems will be pressurized full in virtually a few seconds after the ignition switch is turned to ON (READY) (the tank shut valves open). For the low-range hydrogen system, after the ignition switch is turned to ON (READY), when the "FC Work Mode" in the Data List enters Working and Intermittent Operation turns OFF, the hydrogen injector is caused to open so that hydrogen can be supplied.



c.

Turn the ignition switch off.


Procedure1

a.

Check for a gas leaking sound, and then check if there are hydrogen leaks in the hydrogen pipes and components with a hydrogen gas detector.

A477015C02
6.219,3.813 6.031,3.052 true 6.469,3.281 6.469,2.99 true 4.01,2.719 4.219,2.635 true 4.688,1.406 5.104,0.698 true 5.646,3.49 5.729,2.813 true 6.635,1.833 6.729,1.135 true 4.969,2.323 5.563,2.177 true 4.917,2.146 5.26,2.042 true 4.969,2.469 5.323,2.396 true 2.552,2.135 2.844,1.667 true 4.906,2.031 5.479,1.729 true 2.698,3.563 3.188,2.792 true 1.292,2.104 1.979,1.5 true 0.531,1.885 0.24,0.927 true 4.49,3.708 4.396,3.313 true 6.406,2.865 6.146,2.25 true 4.208,2.177 4.01,1.781 true 4.906,3.885 4.854,3.26 true 5.021,3.052 5.469,3.979 true 0.99,1.854 1.313,1.115 true 6.24,4.01 6.448,4.198 0.208,0.188 10 false *1 5.563,3.563 5.802,3.729 0.24,0.167 10 false *2 5.281,1.969 5.594,2.125 0.313,0.156 10 false *3 5.51,1.635 5.823,1.792 0.313,0.156 10 false *5 2.865,1.51 3.177,1.667 0.313,0.156 10 false *6 1.302,0.979 1.615,1.135 0.313,0.156 10 false *14 6.667,0.958 6.979,1.115 0.313,0.156 10 false *8 6.042,2.063 6.354,2.219 0.313,0.156 10 false *9 5.427,4.021 5.896,4.177 0.469,0.156 10 false *10 2.583,3.583 3.052,3.74 0.469,0.156 10 false *11 2.01,1.375 2.281,1.531 0.271,0.156 10 false *12 0.708,3.26 1.021,3.417 0.313,0.156 10 false : *a 0.719,3.49 1.031,3.646 0.313,0.156 10 false : *b 0.729,3.75 1.042,3.906 0.313,0.156 10 false : *c 0.75,4.01 1.063,4.167 0.313,0.156 10 false : *d 3.823,2.698 4.063,2.865 0.24,0.167 10 false *2 5.375,2.323 5.688,2.479 0.313,0.156 10 false *3 5.177,0.604 5.49,0.76 0.313,0.156 10 false *7 4.781,2.99 5.25,3.146 0.469,0.156 10 false *10 6.406,3.323 6.646,3.49 0.24,0.167 10 false *2 4.385,3.781 4.625,3.948 0.24,0.167 10 false *2 5.615,2.094 5.927,2.25 0.313,0.156 10 false *4 3.885,1.542 4.198,1.698 0.313,0.156 10 false *9 4.844,3.938 5.156,4.094 0.313,0.156 10 false *9 0.115,0.76 0.385,0.917 0.271,0.156 10 false *13
*1 Hydrogen Inlet Receptacle Assembly *2 High-range Hydrogen Pressure Pipe (for filling)
*3 Hydrogen Tank Tube Joint *4 Hydrogen Tank Pressure Sensor (for Inlet Side)
*5 Hydrogen Tank Pressure Sensor (for Outlet Side) *6 No. 1 Hydrogen Tank Assembly
*7 No. 2 Hydrogen Tank Assembly *8 No. 3 Hydrogen Tank Assembly
*9 High-range Hydrogen Pressure Pipe (for feeding) *10 Hydrogen Supply Regulator Assembly
*11 Medium-range Hydrogen Pressure Pipe *12 Low-range Hydrogen Pressure Pipe
*13 FC Stack Assembly *14 Hydrogen Injector
*a High-range Pressure Area (when filling)
(Hydrogen Inlet Receptacle Assembly → Hydrogen Tank Assembly )
*b High-range Pressure Area
(Hydrogen Tank Assembly → Hydrogen Supply Regulator Assembly)
*c Medium-range Pressure Area
(Hydrogen Supply Regulator Assembly → Hydrogen Injector)
*d Low-range Pressure Area
(Hydrogen Injector → FC Stack)



Standard value:

300 ppm or less. (Hydrogen gas detector)


Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the under cover.



OK

5.CHECK EXHAUST HYDROGEN GAS

NG

6.CHECK HYDROGEN GAS LEAKAGE POINT
5.CHECK EXHAUST HYDROGEN GAS
CAUTION:
·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.



Pre-procedure1

a.

Ensure the safety of the areas in front and at the back of the vehicle.


b.

Put wheel chocks and securely apply the parking brake.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / EV / Active Test / Activate the Exhaust Drainage Valve / Data List / FC Work Mode, FC Intermittent Operation, Exhaust Drainage Valve

Powertrain > EV > Active Test
Active Test Display
Activate the Exhaust Drainage Valve
Data List Display
FC Work Mode
FC Intermittent Operation
Exhaust Drainage Valve
50004 397 42006 962,872,818

g.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Working, "FC Intermittent Operation" is OFF, and "Exhaust Drainage Valve" is Close.


Procedure1

a.
A476956C02
0.875,2.563 1.833,1.885 true 2.042,2.042 2.75,1.583 2.75,1.583 2.938,1.573 true 0.604,2.563 0.917,2.76 0.313,0.198 10 true *1 3,1.49 3.313,1.688 0.313,0.198 10 true *2
*1 Tailpipe
*2 Hydrogen Gas Detector Probe


Use the hydrogen gas detector to measure and record the hydrogen concentration in gas released from the tailpipe when the exhaust drainage valve is closed.

NOTICE:
·

Perform this measurement in an environment where there is no wind.

·

Position the hydrogen gas detector probe in an area 100 mm (3.94 in.) away from the tailpipe opening. (Avoid locations underneath the tailpipe opening)

·

Position the hydrogen gas detector probe so that it is free from dropping water that comes from the tailpipe opening.




b.

Perform the "Activate the Exhaust Drainage Valve" Active Test several times over 1 minute, and then, starting from the third test, use the hydrogen gas detector to measure the hydrogen concentration in gas released from the tailpipe when the exhaust drainage valve is open.

HINT:
·

The exhaust drainage valve will open for 1 second each time the Active Test is performed, so measure the hydrogen concentration for several seconds.

·

Hydrogen concentration may not increase while coolant escapes when the valve is first opened. Therefore, start measuring from the third test.

·

There is a delayed response when performing detection using the hydrogen gas detector, so measure for several seconds.

·

"FC Intermittent Operation" in the Data List will be more likely to turn OFF if the accelerator pedal is depressed with the shift state in park (P).




Result:
Result Proceed to
The hydrogen concentration of the hydrogen gas detector will increase when "Exhaust Drainage Valve" in the Data List is Open rather than when "Exhaust Drainage Valve" is Close. A
Other than above* B


*: The exhaust drainage valve is malfunctioning

Exhaust drainage valve is stuck closed:

Regardless of the "Exhaust Drainage Valve Driving Request" being ON or OFF, the concentration shown on the hydrogen gas detector has remained low.


Exhaust drainage valve is stuck open:

Regardless of the "Exhaust Drainage Valve Driving Request" being ON or OFF, the concentration shown on the hydrogen gas detector has remained high when the ignition switch is on (READY).



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE FC STACK ASSEMBLY

B

REPLACE HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY

6.CHECK HYDROGEN GAS LEAKAGE POINT
CAUTION:
·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.



Pre-procedure1

a.

Turn the ignition switch to ON (READY) with the shift lever in P, and check that the Data List "FC Work Mode" is Working and "FC Intermittent Operation" is OFF.

Powertrain > EV > Data List
Tester Display
FC Work Mode
FC Intermittent Operation
50003 397 962,872
HINT:

If there are no leaks, the high-range and medium-range hydrogen systems will be pressurized full in virtually a few seconds after the ignition switch is turned to ON (READY) (the tank shut valves open). For the low-range hydrogen system, after the ignition switch is turned to ON (READY), when the "FC Work Mode" in the Data List enters Working and Intermittent Operation turns OFF, the hydrogen injector is caused to open so that hydrogen can be supplied.



b.

Turn the ignition switch off.


Procedure1

a.

Apply soapy water to locate hydrogen leaking areas.

NOTICE:

Do not apply soapy water to the FC stack assembly. If a hydrogen gas detector identifies gas leaks from the FC stack assembly, replace the FC stack assembly with new one.


Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

REPLACE MALFUNCTIONING PARTS

7.CHECK HYDROGEN GAS LEAKAGE POINT
CAUTION:
·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.



a.

Apply soapy water to locate hydrogen leaking areas.

NOTICE:

Do not apply soapy water to the FC stack assembly. If a hydrogen gas detector identifies gas leaks from the FC stack assembly, replace the FC stack assembly with new one.


Result:
Proceed to
NEXT




NEXT

REPLACE MALFUNCTIONING PARTS