Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  U029387  Lost Communication with Hybrid/EV Powertrain Control Module Missing Message  


DESCRIPTION

The hydrogen fuel control ECU assembly and EV control ECU send and receive signals via CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message A CAN communication error between the hydrogen fuel control ECU assembly and EV control ECU (CAN communication system malfunction) occurs.
(1 trip detection logic)
·

Hydrogen fuel control ECU assembly

·

EV control ECU

·

Wire harness or connector


Master Warning: Comes on Hydrogen Filling Control B

WIRING DIAGRAM

A480719E01
4.333,2.667 5.469,3.01 1.135,0.344 10 false EV Control ECU 6.125,2.792 7.052,3.313 0.927,0.521 10 false Hydrogen Fuel Control ECU 0.573,2.396 1.844,2.656 1.271,0.26 10 false Auxiliary Battery 1.073,1.313 1.979,1.646 0.906,0.333 10 false IGCT NO. 2 0.333,1.302 1.24,1.635 0.906,0.333 10 false R/R RR# 2 1.833,1.885 2.74,2.219 0.906,0.333 10 false IGCT NO. 2 2.802,1.302 3.417,1.625 0.615,0.323 10 false PM-IGCT 4.958,1.26 5.396,1.49 0.438,0.229 10 false CAFH 4.958,1.667 5.396,1.896 0.438,0.229 10 false CAFL 6.406,1.26 6.844,1.49 0.438,0.229 10 false CAFH 6.417,1.646 6.854,1.875 0.438,0.229 10 false CAFL 5.458,1.063 5.604,1.26 0.146,0.198 10 false 6 5.458,1.479 5.604,1.677 0.146,0.198 10 false 7 6.198,1.073 6.375,1.25 0.177,0.177 10 false 15 6.177,1.479 6.354,1.656 0.177,0.177 10 false 16 4.417,1.938 4.854,2.167 0.438,0.229 10 false E1 4.073,1.76 4.219,1.958 0.146,0.198 10 false 4 4.021,1.917 4.458,2.146 0.438,0.229 10 false A17 5.344,1.25 5.781,1.479 0.438,0.229 10 false G14*1 5.344,1.646 5.781,1.875 0.438,0.229 10 false G14*1 6.104,2.625 6.542,2.854 0.438,0.229 10 false G4 4.417,1.542 4.854,1.771 0.438,0.229 10 false MREL 3.552,1.531 3.99,1.76 0.438,0.229 10 false A8*1 4.031,1.365 4.208,1.542 0.177,0.177 10 false 21 3.563,1.125 4,1.354 0.438,0.229 10 false A8*1 4,0.729 4.438,0.958 0.438,0.229 10 false A17 4.406,1.146 4.844,1.375 0.438,0.229 10 false +B2 4.406,0.76 4.844,0.99 0.438,0.229 10 false +B1 4.073,0.958 4.219,1.156 0.146,0.198 10 false 7 4.052,0.552 4.198,0.75 0.146,0.198 10 false 1 2.615,1.427 2.792,1.604 0.177,0.177 10 false 2 1.823,1 2,1.177 0.177,0.177 10 false 3 1.823,1.417 2,1.594 0.177,0.177 10 false 1 2.625,0.99 2.802,1.167 0.177,0.177 10 false 5 0.5,3.396 2.385,3.677 1.885,0.281 10 false : CAN Communication Line 5.917,1.073 6.063,1.271 0.146,0.198 10 false 6 5.917,1.479 6.063,1.677 0.146,0.198 10 false 7 5.771,1.25 6.208,1.479 0.438,0.229 10 false A14*2 5.771,1.646 6.208,1.875 0.438,0.229 10 false A14*2 3.948,1.135 4.385,1.365 0.438,0.229 10 false D15*2 3.938,1.531 4.375,1.76 0.438,0.229 10 false D15*2 3.656,0.938 3.802,1.135 0.146,0.198 10 false 7 3.625,1.365 3.823,1.552 0.198,0.188 10 false 21 2.875,3.156 4.146,3.417 1.271,0.26 10 false *1: for LHD 2.885,3.458 4.156,3.719 1.271,0.26 10 false *2: for RHD

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

A484004

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.

Make sure to remove the EV supply battery assembly service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A341450

After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable (inverter with converter assembly) on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.

·
A484005

After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

When reinstalling the service plug grip to the EV supply battery assembly, after lowering the EV supply battery assembly service plug grip 90°, securely slide it until a "click" sound is heard.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

·

When measuring the resistance of the CAN bus, turn the ignition switch off, wait for at least 1 minute without operating the key, operating any switches, or opening or closing any doors, then disconnect the auxiliary battery cable and wait again for at least 1 minute before measuring the resistance.

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON (IG) and wait for 2 minutes or more.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U029387)
a.

Perform the Health Check using the GTS.


b.

Read the DTCs.

Result:
Result Proceed to
U029387 and other DTCs are output A
U029387 is output B


HINT:

If any DTCs other than U029387 are output, troubleshoot those DTCs first.




A

GO TO DTC CHART

B

2.CONFIRM MODEL
2.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

3.CHECK TERMINAL VOLTAGE (+B1 AND +B2)

B

5.CHECK TERMINAL VOLTAGE (+B1 AND +B2)
3.CHECK TERMINAL VOLTAGE (+B1 AND +B2)

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.
A478491C40
1.979,0.802 2.375,1.156 0.396,0.354 2.604,0.813 3.021,1.156 0.417,0.344 2.427,1.688 2.354,2.417 true 2.635,1.688 3,2.406 true 2.219,1.688 1.781,2.417 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.708,0.917 3.01,1.083 0.302,0.167 10 false A8 2.073,0.917 2.375,1.083 0.302,0.167 10 false A17 2.229,2.448 2.531,2.615 0.302,0.167 10 false +B1 2.958,2.448 3.344,2.615 0.385,0.167 10 false +B2 1.688,2.438 1.99,2.604 0.302,0.167 10 false E1
*a Component with harness connected
(EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A17,A8)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-1 (+B1) - A17-4 (E1) Ignition switch ON 11 to 14 V
A8-7 (+B2) - A17-4 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.



OK

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - HYDROGEN FUEL CONTROL ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - HYDROGEN FUEL CONTROL ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the hydrogen fuel control ECU assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G14,G4)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

Click Connector(G4)Body>Floor Wire / No. 3 Floor Wire>Hydrogen Fuel Control ECU Assembly

G14-6 (CAFH) - G4-15 (CAFH) Always Below 1 Ω
G14-7 (CAFL) - G4-16 (CAFL) Always Below 1 Ω
G14-6 (CAFH) or G4-15 (CAFH) - Body ground and other terminals Always 10 kΩ or higher
G14-7 (CAFL) or G4-16 (CAFL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the hydrogen fuel control ECU assembly connector.


b.

Reconnect the EV control ECU connector.



OK

7.REPLACE EV CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (+B1 AND +B2)

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.
A478491C29
1.979,0.802 2.375,1.156 0.396,0.354 2.604,0.813 3.021,1.156 0.417,0.344 2.427,1.688 2.354,2.417 true 2.635,1.688 3,2.406 true 2.219,1.688 1.781,2.417 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.708,0.917 3.01,1.083 0.302,0.167 10 false D15 2.073,0.917 2.375,1.083 0.302,0.167 10 false A17 2.229,2.448 2.531,2.615 0.302,0.167 10 false +B1 2.958,2.448 3.344,2.615 0.385,0.167 10 false +B2 1.688,2.438 1.99,2.604 0.302,0.167 10 false E1
*a Component with harness connected
(EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A17,D15)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A17-1 (+B1) - A17-4 (E1) Ignition switch ON 11 to 14 V
D15-7 (+B2) - A17-4 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.



OK

6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - HYDROGEN FUEL CONTROL ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - HYDROGEN FUEL CONTROL ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the EV control ECU connector.


b.

Disconnect the hydrogen fuel control ECU assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A14,G4)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(G4)Body>Floor Wire / No. 3 Floor Wire>Hydrogen Fuel Control ECU Assembly

A14-6 (CAFH) - G4-15 (CAFH) Always Below 1 Ω
A14-7 (CAFL) - G4-16 (CAFL) Always Below 1 Ω
A14-6 (CAFH) or G4-15 (CAFH) - Body ground and other terminals Always 10 kΩ or higher
A14-7 (CAFL) or G4-16 (CAFL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the hydrogen fuel control ECU assembly connector.


b.

Reconnect the EV control ECU connector.



OK

7.REPLACE EV CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE EV CONTROL ECU

NEXT

8.CLEAR DTC
8.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > Hydrogen Filling Control > Clear DTCs
50002 494

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 2 minutes or more.


Procedure1

a.

Check for DTCs.

Powertrain > Hydrogen Filling Control > Trouble Codes
50001 494

Result:
Result Proceed to
DTCs are not output A
U029387 is output B


Post-procedure1

a.

Turn the ignition switch off.



A

END

B

REPLACE HYDROGEN FUEL CONTROL ECU ASSEMBLY