Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1DE400  FC Cooling System Performance  


DESCRIPTION

The cooling system of the FC system controls the FC stack temperature so that it can remain at optimum for power generation. The cooling system employs the FC cooling water pump assembly to feed the FC stack with a necessary amount of FC stack coolant so that the FC stack temperature can remain at an appropriate level, and it forces a heated FC stack coolant at the FC stack outlet to flow into the radiator, cooling down and recirculating the FC stack coolant.

If a control failure that indicates a loss of cooling function has occurred due to malfunctions of the FC cooling water temperature control valve or a clogged radiator, the EV control ECU will store this DTC.

A479010C02
4.552,0.521 4.865,0.719 0.313,0.198 10 false *1 4.104,0.292 4.417,0.49 0.313,0.198 10 false *2 2.625,0.26 2.938,0.458 0.313,0.198 10 false *3 2.229,2.365 2.542,2.563 0.313,0.198 10 false *4 0.458,1.354 0.771,1.552 0.313,0.198 10 false *5 5.771,3.5 6.208,3.708 0.438,0.208 10 false *13 3.802,2.719 4.229,2.927 0.427,0.208 10 false *12 2.417,1.302 2.729,1.5 0.313,0.198 10 false *6 0.813,0.073 1.125,0.271 0.313,0.198 10 false *7 3.75,1.813 4.063,2.01 0.313,0.198 10 false *8 3.208,3.448 3.594,3.667 0.385,0.219 10 false *9 5.396,1.469 5.781,1.688 0.385,0.219 10 false *10 5.417,2.271 5.802,2.49 0.385,0.219 10 false *11 6.333,2.563 6.729,2.865 0.396,0.302 10 false *14
*1 FC Stack *2 FC Stack Assembly
*3 FC Cooling Water Pump Assembly *4 FC Cooling Water Temperature Control Valve
*5 FC Radiator Assembly *6 FC Cooling Water Ion Exchanger Assembly
*7 Water Temperature Sensor (for Radiator Outlet Side) *8 Water Temperature Sensor (for FC Stack Outlet Side)
*9 Intercooler *10 Hydrogen Pump
*11 Exhaust Drainage Valve *12 Water Pump Assembly with Motor
*13 Heater Radiator Unit Sub-assembly *14 Electric Heater Sub-assembly


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1DE400 FC Cooling System Performance
·

Difference between the "Radiator Outlet Coolant Temperature (Filtered Value)" and "FC Stack Outlet Coolant Temperature (Filtered Value)" has deviated from an estimated difference value based on the FC power generation

·

"FC Stack Outlet Coolant Temperature (Filtered Value)" increases abnormally

(1 trip detection logic)


·

Amount of FC stack coolant

·

FC stack coolant piping (leakage)

·

FC cooling water temperature control valve

·

FC radiator assembly (Clogged radiator core)

·

Water temperature sensor (for FC stack outlet side)

·

Water temperature sensor (for radiator outlet side)

·

FC cooling water pump assembly


Master Warning: Comes on EV B

HINT:
·

This DTC indicates an insufficient amount of FC stack coolant, FC stack coolant leaks, or malfunctions in the FC cooling water temperature control valve or in the cooling fan controller with motor. If a coolant temperature increases high, the FC system output will be limited.

·

If the FC stack coolant volume decreases, the power consumption of the FC cooling water pump assembly is reduced.



Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection - - - - ○ -

HINT:

By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.


Related Data List
DTC No. Data List
P1DE400
·

Target Radiator Rotary Valve Position

·

Radiator Rotary Valve Position

·

FC Stack Outlet Coolant Temperature (Filtered Value)

·

Radiator Outlet Coolant Temperature (Filtered Value)



Related Active Test
DTC No. Active Test
P1DE400
·

Control the Radiator Fan 1

·

Control the Radiator Rotary Valve

·

Control the FC Coolant Pump



CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:
·

Forcing the SOC of the EV supply battery assembly to decrease by applying electrical loads such as turning on the air conditioning (HOT MAX, maximum airflow), or depressing the accelerator pedal with the shift state in park (P), the "FC Intermittent Operation" of the Data List is easily to enter OFF (power generation mode).


After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle for 10 minutes according to the freeze frame data (Vehicle Speed, Accelerator Degree).

CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.




PROCEDURE

1.CHECK DTC OUTPUT
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


Pre-procedure1

a.

None


Procedure1

a.

According to the display on the GTS, check for DTCs in the Health Check.

Result:
Result Proceed to
Only P1DE400 is output A
P1DE400 is output and DTCs other than the DTCs in the table below are output B
P1DE400 is output and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Microcomputer malfunction/Power source circuit malfunction P1DC896 (EV) FC Coolant Pump Inverter Component Internal Failure
Communication system malfunction P1DC887 (EV) Lost Communication with FC Coolant Pump Inverter Missing Message
Sensor and actuator circuit malfunction P1D2511 (EV) Radiator Outlet Coolant Temperature Sensor Circuit Short to Ground
P1D2515 (EV) Radiator Outlet Coolant Temperature Sensor Circuit Short to Battery or Open
P1D251C (EV) Radiator Outlet Coolant Temperature Sensor Circuit Voltage Out of Range
P1D2A11 (EV) FC Stack Outlet Coolant Temperature Sensor Circuit Short to Ground
P1D2A15 (EV) FC Stack Outlet Coolant Temperature Sensor Circuit Short to Battery or Open
P1D2A1C (EV) FC Stack Outlet Coolant Temperature Sensor Circuit Voltage Out of Range
P1D2F96 (EV) FC Coolant Pump Component Internal Failure
P1DD514 (FC) Radiator Rotary Valve Circuit 1 Circuit Short to Ground or Open
P1EFD14 (FC) Radiator Rotary Valve Circuit 2 Circuit Short to Ground or Open
P1EFE14 (FC) Radiator Rotary Valve Circuit 3 Circuit Short to Ground or Open
P1EFF14 (FC) Radiator Rotary Valve Circuit 4 Circuit Short to Ground or Open
System malfunction P1D2F00 (EV) FC Coolant Pump Performance
P0A784B (Hybrid (EV) Control System) Drive Motor "A" Inverter Over Temperature
P0AA749 (Hybrid (EV) Control System) Hybrid/EV Battery Voltage Isolation Sensor Circuit Internal Electronic Failure
P1C7C49 (Hybrid (EV) Control System) Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure
P1C7D49 (Hybrid (EV) Control System) Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure
P1C7E49 (Hybrid (EV) Control System) Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure
P1C7F49 (Hybrid (EV) Control System) Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure
P1EED49 (Hybrid (EV) Control System) Hybrid/EV Battery Voltage System Isolation (FC Area) Internal Electronic Failure
P1EEE49 (Hybrid (EV) Control System) Hybrid/EV Battery Voltage System Isolation (Hydrogen Pump Area) Internal Electronic Failure
P1EEF49 (Hybrid (EV) Control System) Hybrid/EV Battery Voltage System Isolation (FC Coolant Pump Area) Internal Electronic Failure


HINT:

DTC P1DE400 may be store due to problems that cause the DTCs shown above to output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order of the listed DTCs shown in the table above.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CLEAR DTC

B

2.CLEAR DTC

C

2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

3.CHECK VEHICLE CONDITION
3.CHECK VEHICLE CONDITION
a.

Make sure that the front side of the radiator grille is not blocked with anything.


b.

Ask the customer if the front side of the radiator grille was blocked with anything.


Result:
Result Proceed to
Not blocked. A
Is/was blocked. B


HINT:

If the radiator grille is blocked, the FC coolant temperature will increase and this DTC may be stored.



A

4.CHECK FC RADIATOR ASSEMBLY

B

IF EQUIPPED, EXPLAIN TO CUSTOMER THAT OPTIONAL COMPONENTS WILL BE REMOVED

4.CHECK FC RADIATOR ASSEMBLY
a.

Check that the radiator core is not clogged, deformed or damaged.

OK:

Radiator core is not clogged, deformed or damaged.


Result:
Proceed to
OK
NG




OK

5.CHECK COOLANT (FC STACK COOLANT) LEAK

NG

REPAIR OR REPLACE FC RADIATOR ASSEMBLY

5.CHECK COOLANT (FC STACK COOLANT) LEAK
a.

Check the FC stack coolant level in the FC radiator reserve tank.


b.

Check for FC coolant leaks.

Click hereEngine / Hybrid System>COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION

Result:
Result Proceed to
No leaks are found and the FC coolant level in the FC radiator reserve tank is above the low line. A
No leaks are found and the FC coolant level in the FC radiator reserve tank is below the low line. B
FC coolant leaks are evident. C


HINT:
·

After repairing the FC coolant leaks and adding coolant, perform the "Control the FC Coolant Pump" and "Control the Radiator Fan 1" Active Test and make sure that there are no malfunctions.

·

If a coolant leak cannot be found despite that the coolant in the radiator reserve tank is below the Low level, leakage may have occurred inside the FC stack or in the air conditioning system.

·

If there is a leak in the FC stack, DTC P0AA649 may be output to the EV control ECU.





A

6.CHECK COOLANT HOSE

B

14.ADD FC STACK COOLANT

C

INSPECT COOLANT LEAK AND ADD COOLANT

6.CHECK COOLANT HOSE
a.

Check that the cooling system hoses are not kinked or clogged.

OK:

The cooling system hoses are not kinked or clogged



Result:
Proceed to
OK
NG



OK

7.INSPECT FC COOLING WATER ION EXCHANGER ASSEMBLY

NG

REPAIR OR REPLACE COOLANT HOSE

7.INSPECT FC COOLING WATER ION EXCHANGER ASSEMBLY
a.

Remove the FC cooling water ion exchanger assembly filter.


b.

Check for tears in the filter or discharge of the ion exchanger resin.

OK:

No tears in the filter or discharge of the ion exchanger resin is observed.



Result:
Proceed to
OK
NG



OK

8.PERFORM ACTIVE TEST USING GTS (CONTROL THE RADIATOR FAN 1)

NG

REPLACE COOLING SYSTEM COMPONENTS
a.

If ion exchanger resin discharge is observed, replace all cooling system components.

HINT:

If there are any cracks, etc. in the discharged resin, replace all cooling system components as it may pass through the stack.




8.PERFORM ACTIVE TEST USING GTS (CONTROL THE RADIATOR FAN 1)

Pre-procedure1

a.

None


Procedure1

a.

Perform the Active Test.

Powertrain > EV > Active Test
Active Test Display
Control the Radiator Fan 1
Data List Display
Radiator Fan 1 Drive Voltage
50004 397 18 705
OK:

The cooling fan rotates


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE RADIATOR ROTARY VALVE)

NG

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE RADIATOR ROTARY VALVE)

Pre-procedure1

a.

Drive in city streets for approximately 10 minutes to warm up.

Powertrain > EV > Data List
Tester Display
FC Stack Outlet Coolant Temperature (Filtered Value)
50003 397 998
HINT:

Raise the "FC Stack Outlet Coolant Temperature (Filtered Value)" in the Data List to approximately 60°C (140°F)



Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Active Test
Active Test Display
Control the Radiator Rotary Valve
Data List Display
Radiator Rotary Valve Drive Position
Target Radiator Rotary Valve Position
Radiator Rotary Valve Position
FC Work Mode
FC Intermittent Operation
Main Radiator Fan Voltage
Radiator Outlet Coolant Temperature (Filtered Value)
50004 397 15 697,905,906,962,872,742,904

b.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Working and "FC Intermittent Operation" is OFF. "step (1)"


c.

Using Active Tests, set the "Control the Radiator Rotary Valve" to 0%.


d.

Turn the air conditioning on (Lo/COOL MAX, maximum airflow) to actuate the cooling fan of the FC radiator assembly.


e.

Check changes in the "Radiator Outlet Coolant Temperature (Filtered Value)" in the Data List for 1 minute.

NOTICE:

If the "FC Stack Outlet Coolant Temperature (Filtered Value)" is above 70°C (158°F), perform the operations instructed below to cool it down to approximately 60°C (140°F), and perform the procedure from step (1) again. If the temperature does not decrease, it is suspected that the FC cooling water temperature control valve is malfunctioning.

1.

Using Active Tests, set the "Control the Radiator Rotary Valve" to 100%.

2.

Turn the air conditioning on to actuate the cooling fan of the FC radiator assembly, allowing the "FC Stack Outlet Coolant Temperature (Filtered Value)" to decrease to approximately 60°C (140°F).



HINT:
·

In order to actuate the FC cooling water pump assembly, put the shift state in park (P) and turn the ignition switch to ON (READY) so that the "FC Work Mode" and "FC Intermittent Operation" in the Data List is in Working and OFF respectively.

·

If the Active Test "Control the Radiator Rotary Valve" is set to 0%, the FC stack coolant begins circulating without bypassing the FC radiator assembly. Thus, even though the cooling fan is switched between ON and OFF, the "Radiator Outlet Coolant Temperature (Filtered Value)" does not vary virtually.




f.

Turn the air conditioning off to stop the cooling fan of the FC radiator assembly.


g.

Using Active Tests, set the "Control the Radiator Rotary Valve" to 100%.


h.

Turn the air conditioning on (Lo/COOL MAX, maximum airflow) to actuate the cooling fan of the FC radiator assembly.


i.

Check changes in the "Radiator Outlet Coolant Temperature (Filtered Value)" in the Data List for 1 minute.

HINT:
·

In order to actuate the FC cooling water pump assembly, put the shift state in park (P) and turn the ignition switch to ON (READY) so that the "FC Work Mode" and "FC Intermittent Operation" in the Data List is in Working and OFF respectively.

·

If the Active Test "Control the Radiator Rotary Valve" is set to 100%, the FC stack coolant begins circulating through the radiator assembly. For that reason, the "Radiator Outlet Coolant Temperature (Filtered Value)" decreases when the cooling fan is actuated.



Reference example (Shift state in park (P), and the air conditioning is switched between ON and OFF)
A479992E01
4.135,2.521 4.646,1.938 false 0.958,5.99 1.354,6.479 false 4.354,5.385 3.969,6.156 false 2.323,5.385 2.125,5.906 false 0.073,0.094 1.542,0.948 1.469,0.854 10 false Target Radiator Rotary Valve Position 2.604,0.042 4.646,0.615 2.042,0.573 10 false "Control the Radiator Rotary Valve" Active Test: 1 → 100% 0.083,1.802 1.5,2.354 1.417,0.552 10 false Main Radiator Fan Voltage 0.25,0.594 0.865,0.792 0.615,0.198 10 false 100% 0.385,1.167 1,1.365 0.615,0.198 10 false 0% 0.385,3.021 1,3.219 0.615,0.198 10 false 0 V 0.375,2.469 0.99,2.667 0.615,0.198 10 false 9 V 1.625,1.781 2.677,2.354 1.052,0.573 10 false Air conditioning is turned ON 4.74,1.76 5.792,2.333 1.052,0.573 10 false Air conditioning is turned ON 3.208,1.771 4.26,2.344 1.052,0.573 10 false Air conditioning is turned OFF 0.052,3.667 3.292,4.063 3.24,0.396 10 false Radiator Outlet Coolant Temperature (Filtered Value) 0.26,4.188 0.875,4.385 0.615,0.198 10 false 55°C 0.271,4.854 0.885,5.052 0.615,0.198 10 false 45°C 1.76,3.927 3.76,4.354 2,0.427 10 false No decrease in the temperature 4.917,3.938 6.74,4.448 1.823,0.51 10 false Decrease in the temperature 0.198,5.854 1.115,6.313 0.917,0.458 10 false FC Radiator Assembly 2.385,5.292 4.156,5.854 1.771,0.563 10 false Water Temperature Sensor (for Radiator Outlet Side) 4.427,5.271 5.74,5.833 1.313,0.563 10 false FC Cooling Water Pump Assembly 4.844,7.281 6.156,7.76 1.313,0.479 10 false FC Stack Assembly 2.229,7.188 4.115,7.708 1.885,0.521 10 false FC Cooling Water Temperature Control Valve 1.854,8.01 5.813,8.396 3.958,0.385 10 false : Flow of coolant (Target Radiator Rotary Valve Position = 100%) 1.865,8.375 5.823,8.76 3.958,0.385 10 false : Flow of coolant (Target Radiator Rotary Valve Position = 0%)


Result:
Result Proceed to
Both following conditions 1 and 2 are met:
1.

When the "Target Radiator Rotary Valve Position" is 0%, a decrease in the "Radiator Outlet Coolant Temperature (Filtered Value)" is less than 2°C (3.6°F) if the air conditioning is turned from OFF to ON

2.

When the "Target Radiator Rotary Valve Position" is 100%, a decrease in the "Radiator Outlet Coolant Temperature (Filtered Value)" is 2°C (3.6°F) or more if the air conditioning is turned from OFF to ON


A
Other than above B


Post-procedure1

a.

Turn the ignition switch off.



A

10.INSPECT ENGINE COOLANT TEMPERATURE SENSOR (FOR RADIATOR OUTLET SIDE)

B

12.PERFORM ACTIVE TEST USING GTS (CONTROL THE FC COOLANT PUMP)
10.INSPECT ENGINE COOLANT TEMPERATURE SENSOR (FOR RADIATOR OUTLET SIDE)

OK

11.INSPECT ENGINE COOLANT TEMPERATURE SENSOR (FOR FC STACK OUTLET SIDE)

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (FOR RADIATOR OUTLET SIDE)

11.INSPECT ENGINE COOLANT TEMPERATURE SENSOR (FOR FC STACK OUTLET SIDE)

OK

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (FOR FC STACK OUTLET SIDE)

12.PERFORM ACTIVE TEST USING GTS (CONTROL THE FC COOLANT PUMP)

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


Procedure1

a.

Check that "FC Stack Outlet Coolant Temperature (Filtered Value)" is 40°C or more.

Powertrain > EV > Active Test
Active Test Display
Control the FC Coolant Pump
Data List Display
FC Coolant Pump Drive Speed
FC Coolant Pump Speed
Target FC Coolant Pump Speed
FC Stack Outlet Coolant Temperature (Filtered Value)
50004 397 17 704,909,908,998
HINT:

If 40°C or less, drive the vehicle on urban roads for approximately 10 minutes to warm it up.



b.

Perform the Active Test for 10 seconds or more at 3100 rpm.


Result:
Proceed to
NEXT


Post-procedure1

a.

None



NEXT

13.CHECK DTC OUTPUT
13.CHECK DTC OUTPUT

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1D2F00 is output A
DTCs are not output B


HINT:

P1DE400 (FC Cooling System Performance) may be output due to the FC cooling water pump assembly, so check if P1D2F00 (FC Coolant Pump Performance) is output.



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE FC COOLING WATER PUMP ASSEMBLY

B

REPLACE FC COOLING WATER TEMPERATURE CONTROL VALVE

14.ADD FC STACK COOLANT

Pre-procedure1

a.

None


b.

Add FC stack coolant and bleed air.


Procedure1

a.

After bleeding air, check the coolant level and check for coolant leaks again.

OK:

No leaks are found and the FC coolant level in the FC radiator reserve tank is above the low line.


HINT:
·

After repairing the FC coolant leaks and adding coolant, perform the "Control the FC Coolant Pump" and "Control the Radiator Fan 1" Active Test and make sure that there are no malfunctions.

·

If a coolant leak cannot be found despite that the coolant in the radiator reserve tank is below the Low level, leakage may have occurred inside the FC stack or in the air conditioning system.

In this case, add coolant and then bleed air from the coolant. If the coolant level is still too low but a coolant leak cannot be confirmed even in the air conditioning system, the coolant leak is in the FC stack. Replace the FC stack.

·

If there is a leak in the FC stack, DTC P0AA649 may be output to the EV control ECU.



Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

END

NG

REPLACE FC STACK ASSEMBLY