Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1E9111  FC Negative Contactor Control Circuit Short to Ground  P1E9115  FC Negative Contactor Control Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P1E9011.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1E9011

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1E9111 FC Negative Contactor Control Circuit Short to Ground The drive monitor voltage is less than 0.1 V during FC stack main relay negative side (FRG) relay ON control.
Primary circuit of FRG is malfunctioning.
(1 trip detection logic)
·

Wire harness or connector

·

FC boost control ECU

·

FC stack main relay (FRG)

·

No. 1 FC converter wire

·

No. 2 FC converter wire

·

EV control ECU


Master Warning: Comes on EV A
P1E9115 FC Negative Contactor Control Circuit Short to Battery or Open The drive monitor voltage continues to be more than 2.9 V during FC stack main relay negative side (FRG) relay ON control.
Primary circuit of FRG is malfunctioning.
(1 trip detection logic)
·

Wire harness or connector

·

FC boost control ECU

·

FC stack main relay (FRG)

·

No. 1 FC converter wire

·

No. 2 FC converter wire

·

EV control ECU


Master Warning: Comes on EV A

Related Data List
DTC No. Data List
P1E9111
·

VL-Voltage before Boosting

·

FCDC Output Voltage

·

FC Precharge Relay Status

·

FC Positive Relay Drive Status

·

FC Negative Relay Drive Status

·

FC Precharge Relay Drive Request

·

FC Negative Relay Drive Request

·

FC Positive Relay Drive Request

·

FC Converter Shutdown Request

·

Motor Inverter Shutdown Status

·

FC Air Compressor Gate Shutdown Request


P1E9115

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

A484004

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the EV supply battery assembly service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A341450

After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.

·
A484005

After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:
·

If DTC P1E9111 or P1E9115 is output, the ignition switch cannot be turned to ON (READY).

·

After the repair, clear the DTCs, perform the following procedure and check that the same DTC (including pending DTC) is not output.

(a)

Turn the ignition switch off and wait for 10 minutes or more.

(b)

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

(c)

Turn the ignition switch off and wait for 10 minutes or more.




PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

2.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

2.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC CONVERTER ASSEMBLY (FRG RELAY))

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC CONVERTER ASSEMBLY (FRG RELAY))

Pre-procedure1

a.

Disconnect the EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A15)Location & Routing

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A15-3 (FRG+) - A15-2 (FRG-) Ignition switch off 11.07 to 13.53 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the EV control ECU connector.



OK

NG

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC CONVERTER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed to EV supply battery assembly and the FC converter power outlet cable (inverter with converter assembly) is not connected to the FC converter assembly.

NOTICE:

After removing the EV supply battery assembly service plug grip and FC converter power outlet cable on FC converter side, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the electric heater sub-assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER ASSEMBLY>REMOVAL



c.

Disconnect the FC converter assembly connector.


d.

Disconnect the EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A15,B19)Location & Routing

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(B19)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

A15-3 (FRG+) - B19-7 (FRG+) Ignition switch off Below 1 Ω
A15-2 (FRG-) - B19-1 (FRG-) Ignition switch off Below 1 Ω
A15-3 (FRG+) or B19-7 (FRG+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A15-2 (FRG-) or B19-1 (FRG-) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the EV control ECU connector.


b.

Reconnect the FC converter assembly connector.


c.

Install the electric heater sub-assembly.



OK

REPLACE FC CONVERTER AND FC STACK ASSEMBLY COMPONENT PARTS

Replace the FC converter and FC stack assembly components listed below.

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL

·

FC boost control ECU

·

FC stack main relay (FRG)

·

No. 1 FC converter wire

·

No. 2 FC converter wire


HINT:
·

Refer to the parts location for the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PARTS LOCATION

·

Refer to the system description for the parts location of the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>SYSTEM DESCRIPTION




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR