Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0453477 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0AAC11  Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Ground  P0AAC15  Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

The EV battery intake air temperature sensor is mounted on the EV supply battery assembly. The resistance of the sensor varies in accordance with changes in the intake air temperature. The characteristics of the EV battery intake air temperature sensor are the same as those of the battery temperature sensors (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9B11). The battery ECU assembly uses signals from the EV battery intake air temperature sensor to control the air volume of the battery cooling blower assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0AAC11 Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Ground The EV battery intake air temperature sensor output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 2 EV battery pack wire (EV battery intake air temperature sensor)

·

Battery ECU assembly

·

Wire harness or connector

·

No. 1 EV battery junction block assembly


Master Warning:
Comes on
EV Battery A
P0AAC15 Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open The EV battery intake air temperature sensor output voltage is higher than the standard value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 2 EV battery pack wire (EV battery intake air temperature sensor)

·

Battery ECU assembly

·

Wire harness or connector

·

No. 1 EV battery junction block assembly


Master Warning:
Comes on
EV Battery A

HINT:

After checking for the above DTCs, check the EV Battery Data List item "Hybrid/EV Battery Cooling Fan Intake Air Temperature 1" using the GTS.


Displayed Temperature Malfunction
-45°C (-49°F) or less Open or +B short circuit
95°C (203°F) or higher GND short

Related Data List
DTC No. Data List
P0AAC11 Hybrid/EV Battery Cooling Fan Intake Air Temperature 1
P0AAC15

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds.

4.

Enter the following menus: Powertrain / EV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

C375034E03
1.417,0.938 1.99,0.24 1.99,0.24 2.24,0.24 false 4.875,2.188 5.188,2.385 0.313,0.198 10 false z26 5.177,2.188 6.781,2.438 1.604,0.25 10 false Battery ECU Assembly 2.344,0.073 3.698,0.427 1.354,0.354 10 false EV Battery Intake Air Temperature Sensor 0.385,2.125 2.917,2.344 2.531,0.219 10 false EV Supply Battery Assembly 5.281,0.833 5.74,1.031 0.458,0.198 10 false TC0 5.292,1.323 5.75,1.521 0.458,0.198 10 false GC0 5.063,1.333 5.219,1.531 0.156,0.198 10 false 8 4.99,0.844 5.302,1.042 0.313,0.198 10 false 28

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV BATTERY, EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV Battery > Trouble Codes
50001 398
Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0AAC11 or P0AAC15 for Hybrid battery system is output A
P0AAC11 or P0AAC15 is output and DTCs other than the DTCs in the table below are output B
P0AAC11 or P0AAC15 is output and Hybrid battery system DTCs in the table below are output C
P0AAC11 or P0AAC15 is output and Hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA

B

2.CHECK FREEZE FRAME DATA

C

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

D

2.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

a.

Check and record the "Hybrid/EV Battery Current Sensor Power Supply Voltage" freeze frame data.

Powertrain > EV Battery > Trouble Codes
50001 398
HINT:

Use this for reference when measuring the EV battery current sensor power supply voltage.



Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



Procedure1

a.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Check the connections of the z26 battery ECU assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the upper No. 1 EV battery cover sub-assembly.



OK

4.CHECK INSTALLATION OF EV BATTERY INTAKE AIR TEMPERATURE SENSOR

NG

CONNECT SECURELY

4.CHECK INSTALLATION OF EV BATTERY INTAKE AIR TEMPERATURE SENSOR
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper EV battery cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



Procedure1

a.
C371963

Visually check the installation condition of the EV battery intake air temperature sensor.


Result:
Result Proceed to
The EV battery intake air temperature sensor is installed in the correct location and its claws are engaged securely. A
The claws of the EV battery intake air temperature sensor are damaged. B
The EV battery intake air temperature sensor is not installed correctly, but its claws are not damaged. C


Post-procedure1

a.

Install the upper EV battery cover panel.



A

5.CHECK EV BATTERY (EV BATTERY INTAKE AIR TEMPERATURE SENSOR)

B

REPLACE NO. 2 EV BATTERY PACK WIRE (EV BATTERY INTAKE AIR TEMPERATURE SENSOR)

C

INSTALL PARTS CORRECTLY

5.CHECK EV BATTERY (EV BATTERY INTAKE AIR TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374183C25
1.469,0.323 1.917,0.615 0.448,0.292 2.042,1.469 2.573,0.698 true 2.542,2.583 2.052,1.76 true 1.583,0.406 1.896,0.604 0.313,0.198 10 false z26 2.656,0.604 3.115,0.802 0.458,0.198 10 true GC0 2.625,2.573 3.083,2.771 0.458,0.198 10 true TC0 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a
*a Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Thermistor Temperature Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-28 (TC0) - z26-8 (GC0) Always 0 to 10°C (32 to 50°F) 17.7 to 27.8 kΩ
z26-28 (TC0) - z26-8 (GC0) Always 10 to 20°C (50 to 68°F) 12.0 to 18.2 kΩ
z26-28 (TC0) - z26-8 (GC0) Always 20 to 30°C (68 to 86°F) 8.22 to 12.2 kΩ
z26-28 (TC0) - z26-8 (GC0) Always 30 to 40°C (86 to 104°F) 5.74 to 8.41 kΩ
z26-28 (TC0) - z26-8 (GC0) Always 40 to 50°C (104 to 122°F) 4.09 to 5.91 kΩ



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connectors.


b.

Install the upper No.1 EV battery cover sub-assembly.



OK

6.CHECK EV BATTERY (EV BATTERY INTAKE AIR TEMPERATURE SENSOR)

NG

REPLACE NO. 2 EV BATTERY PACK WIRE (EV BATTERY INTAKE AIR TEMPERATURE SENSOR)

6.CHECK EV BATTERY (EV BATTERY INTAKE AIR TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374183C25
1.469,0.323 1.917,0.615 0.448,0.292 2.042,1.469 2.573,0.698 true 2.542,2.583 2.052,1.76 true 1.583,0.406 1.896,0.604 0.313,0.198 10 false z26 2.656,0.604 3.115,0.802 0.458,0.198 10 true GC0 2.625,2.573 3.083,2.771 0.458,0.198 10 true TC0 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a
*a Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-28 (TC0) - Body ground and other terminals Always 10 kΩ or higher
z26-8 (GC0) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connectors.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

7.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

REPLACE NO. 2 EV BATTERY PACK WIRE (EV BATTERY INTAKE AIR TEMPERATURE SENSOR)

7.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
C371962N08
1.563,0.469 1.99,0.729 0.427,0.26 1.635,0.5 1.927,0.688 0.292,0.188 10 true z23

Disconnect the z23 battery current sensor connector from the No. 1 EV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C373318C13
1.49,1.688 1.875,1.896 0.385,0.208 1.5,0.135 1.885,0.344 0.385,0.208 1.604,0.99 1.073,0.583 true 0.698,2.365 0.469,1.927 true 0.865,3.063 0.958,2.594 true 0.979,1.156 1.604,1.156 true 1.594,0.177 1.906,0.375 0.313,0.198 10 false z23 1.573,1.729 1.885,1.927 0.313,0.198 10 false z26 0.25,1.781 0.708,1.979 0.458,0.198 10 false VIB 0.792,0.479 1.25,0.677 0.458,0.198 10 false VIB 0.76,3.104 1.219,3.302 0.458,0.198 10 false GIB 0.677,1.094 1.135,1.292 0.458,0.198 10 false GIB 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.104,1.479 0.417,1.635 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 1 EV Battery Junction Block Assembly (Battery Current Sensor))
*b Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(z26,z23)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

Click Connector(z23)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z26-19 (VIB) - z23-1 (VIB) Always Below 1 Ω
z26-37 (GIB) - z23-3 (GIB) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(z26,z23)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

Click Connector(z23)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z26-19 (VIB) or z23-1 (VIB) - Body ground and other terminals Always 10 kΩ or higher
z26-37 (GIB) or z23-3 (GIB) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z23 battery current sensor connector to the No. 1 EV battery junction block assembly.


b.

Reconnect the z26 battery ECU assembly connector.


c.

Install the upper No. 1 EV battery cover sub-assembly.



OK

8.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373319C08
1.521,2.688 1.979,2.958 0.458,0.271 0.573,3.042 1.74,3.823 true 2.5,3.594 2.927,2.99 true 0.125,0.156 0.354,0.333 0.229,0.177 10 true *a 1.583,2.74 2.042,2.938 0.458,0.198 10 false G156 0.25,2.875 0.615,3.052 0.365,0.177 10 false IGCT 2.958,2.823 3.354,3.021 0.396,0.198 10 false GND
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Apply auxiliary battery voltage between No. 2 EV battery pack wire connector terminals G156-14 (IGCT) - G156-1 (GND).

NOTICE:

Make sure that the battery positive and battery negative do not contact one another.



Procedure1

a.
C371921C11
1.531,1.51 1.896,1.75 0.365,0.24 0.323,1.635 0.521,2.344 true 0.813,2.656 0.5,3.146 true 0.115,0.115 0.427,0.271 0.313,0.156 10 false *a 0.198,1.438 0.656,1.635 0.458,0.198 10 false VIB 0.26,3.115 0.719,3.313 0.458,0.198 10 false GIB 1.594,1.552 1.896,1.76 0.302,0.208 10 false z26
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-19 (VIB) - z26-37 (GIB) Auxiliary battery positive (+) → G156-14 (IGCT)
Auxiliary battery negative (-) → G156-1 (GND)
4.6 to 5.4 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the G156 No. 2 EV battery pack wire connector from the auxiliary battery.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

NG

9.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
9.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper EV battery cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C371962N08
1.563,0.469 1.99,0.729 0.427,0.26 1.635,0.5 1.927,0.688 0.292,0.188 10 true z23

Disconnect the z23 battery current sensor connector from the No. 1 EV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
C373319C08
1.521,2.688 1.979,2.958 0.458,0.271 0.573,3.042 1.74,3.823 true 2.5,3.594 2.927,2.99 true 0.125,0.156 0.354,0.333 0.229,0.177 10 true *a 1.583,2.74 2.042,2.938 0.458,0.198 10 false G156 0.25,2.875 0.615,3.052 0.365,0.177 10 false IGCT 2.958,2.823 3.354,3.021 0.396,0.198 10 false GND
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Apply auxiliary battery voltage between No. 2 EV battery pack wire connector terminals G156-14 (IGCT) - G156-1 (GND).

NOTICE:

Make sure that the battery positive and battery negative do not contact one another.



Procedure1

a.
A479524C01
2.333,1.135 2.729,1.365 0.396,0.229 1.573,1.146 0.99,0.906 true 1,1.771 1.573,1.458 true 0.729,0.823 1.063,1.063 0.333,0.24 10 false VIB 0.729,1.719 1.094,1.969 0.365,0.25 10 false GIB 0.188,0.146 0.427,0.292 0.24,0.146 10 false *a 2.427,1.167 2.802,1.469 0.375,0.302 10 false z23
*a Front view of wire harness connector
(to No. 1 EV Battery Junction Block Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z23)Location & Routing

Click Connector(z23)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z23-1 (VIB) - z23-3 (GIB) Auxiliary battery positive (+) → G156-14 (IGCT)
Auxiliary battery negative (-) → G156-1 (GND)
4.6 to 5.4 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the G156 No. 2 EV battery pack wire connector from the auxiliary battery.


b.

Reconnect the z23 battery current sensor connector to the No. 1 EV battery junction block assembly.


c.

Install the upper EV battery cover panel.



OK

REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NG