Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0453477 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A9B11  Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Ground  P0A9B15  Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open  P0AC511  Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Ground  P0AC515  Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Auxiliary Battery or Open  P0ACA11  Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Ground  P0ACA15  Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open  P0AE811  Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Ground  P0AE815  Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Auxiliary Battery or Open  P0BC211  Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Ground  P0BC215  Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Auxiliary Battery or Open  P0C3311  Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Ground  P0C3315  Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

The battery temperature sensors are provided at 6 locations of the EV supply battery assembly. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance with changes in the EV battery temperature. The lower the battery temperature, the higher the thermistor resistance. Conversely, the higher the temperature, the lower the resistance. The battery ECU assembly uses the battery temperature sensors to detect the EV battery temperature, and sends the detected value to the battery ECU assembly. Based on the results of this detection, the battery ECU assembly controls the blower fan. (The blower fan starts when the EV battery temperature rises above a predetermined level.)

Temperature Sensor Identification Cross Reference Table:
DTC Title Sensor Battery Temperature Sensor GTS Display
A 0 1
B 1 2
C 2 3
D 3 4
E 4 5
F 5 6


HINT:

Use the reference table above to determine which battery temperature sensor corresponds to each DTC. For example, sensor A in the DTC title column is battery temperature sensor 0. This sensor is displayed as Hybrid/EV Battery Temperature 1 in the Data List.


A171806E05
1.896,0.031 2.635,0.188 0.74,0.156 10 false Reference: 2.167,0.354 2.427,0.5 0.26,0.146 10 false 250 2.167,0.677 2.427,0.823 0.26,0.146 10 false 200 2.167,0.979 2.427,1.125 0.26,0.146 10 false 150 2.177,1.271 2.438,1.417 0.26,0.146 10 false 100 2.25,1.583 2.438,1.729 0.188,0.146 10 false 50 2.333,1.896 2.438,2.042 0.104,0.146 10 false 0 3.271,2.25 3.375,2.396 0.104,0.146 10 false 0 2.573,2.25 2.802,2.417 0.229,0.167 10 false -40 2.917,2.25 3.146,2.417 0.229,0.167 10 false -20 3.521,2.25 3.698,2.417 0.177,0.167 10 false 20 3.813,2.25 3.99,2.417 0.177,0.167 10 false 40 4.094,2.25 4.271,2.417 0.177,0.167 10 false 60 4.396,2.25 4.573,2.417 0.177,0.167 10 false 80 4.646,2.25 4.906,2.417 0.26,0.167 10 false 100 3.177,2.458 3.448,2.604 0.271,0.146 10 false (32) 2.531,2.448 2.865,2.615 0.333,0.167 10 false (-40) 2.906,2.448 3.167,2.615 0.26,0.167 10 false (-4) 3.458,2.448 3.729,2.615 0.271,0.167 10 false (68) 3.708,2.448 4.073,2.615 0.365,0.167 10 false (104) 4.031,2.448 4.375,2.615 0.344,0.167 10 false (140) 4.354,2.448 4.708,2.615 0.354,0.167 10 false (176) 4.677,2.448 5.021,2.615 0.344,0.167 10 false (212) 5.094,2.24 5.365,2.438 0.271,0.198 10 false (°C) 5.094,2.448 5.427,2.646 0.333,0.198 10 false (°F) 1.823,0.375 2.115,0.573 0.292,0.198 10 false (kΩ) 1.24,1.146 1.969,1.333 0.729,0.188 10 false Resistance 5.531,2.24 6.875,2.427 1.344,0.188 10 false Battery Temperature 2.604,0.042 5.698,0.219 3.094,0.177 10 false Battery Temperature Sensor Characteristic Graph

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0A9B11 Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0A9B15 Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0AC511 Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0AC515 Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0ACA11 Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0ACA15 Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0AE811 Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 2 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0AE815 Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 2 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0BC211 Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 2 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0BC215 Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 2 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0C3311 Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 2 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A
P0C3315 Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 2 EV supply stack sub-assembly

·

EV battery terminal block

·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Master Warning:
Comes on
EV Battery A

Temperature Displayed Malfunction
Below -45°C (-49°F) Open or +B short circuit
95°C (203°F) or higher GND short circuit

Related Data List
DTC No. Data List
P0A9B11 Hybrid/EV Battery Temperature 1 to 6
Hybrid/EV Battery Current Sensor Power Supply Voltage
P0A9B15
P0AC511
P0AC515
P0ACA11
P0ACA15
P0AE811
P0AE815
P0BC211
P0BC215
P0C3311
P0C3315

HINT:
·

After checking for the above DTCs, check the EV Battery Data List item "Hybrid/EV Battery Temperature" using the GTS.

·

If the vehicle as is left as is for 24 hours, the value of "Hybrid/EV Battery Temperature" will be almost the same as the ambient temperature.



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / EV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

C375032E03
0.229,2.26 0.698,2.479 0.469,0.219 10 false z23 0.667,9.01 4.333,9.208 3.667,0.198 10 false No. 2 EV Supply Stack Sub-assembly 3.427,8.906 3.885,9.104 0.458,0.198 10 false B 3.417,5.365 3.875,5.563 0.458,0.198 10 false A 0.688,5.49 4.354,5.688 3.667,0.198 10 false No. 1 EV Supply Stack Sub-assembly 5.396,0.792 5.854,0.99 0.458,0.198 10 false VIB 2.708,0.792 3.167,0.99 0.458,0.198 10 false VIB 5.406,1.167 5.719,1.365 0.313,0.198 10 false IB0 2.729,1.167 3.042,1.365 0.313,0.198 10 false IB0 2.74,1.542 3.198,1.74 0.458,0.198 10 false IB1 5.417,1.542 5.875,1.74 0.458,0.198 10 false IB1 2.719,1.875 3.177,2.073 0.458,0.198 10 false GIB 5.406,1.875 5.865,2.073 0.458,0.198 10 false GIB 3.125,1.167 3.281,1.365 0.156,0.198 10 false 4 3.125,0.802 3.281,1 0.156,0.198 10 false 1 3.125,1.542 3.281,1.74 0.156,0.198 10 false 2 3.125,1.875 3.281,2.073 0.156,0.198 10 false 3 5.063,1.542 5.375,1.74 0.313,0.198 10 false 38 5.042,0.802 5.354,1 0.313,0.198 10 false 19 5.052,1.167 5.365,1.365 0.313,0.198 10 false 18 5.073,1.875 5.385,2.073 0.313,0.198 10 false 37 0.865,3.948 2.938,4.188 2.073,0.24 10 false Battery Temperature Sensor 1 0.844,4.875 2.854,5.146 2.01,0.271 10 false Battery Temperature Sensor 2 0.854,6.542 2.885,6.844 2.031,0.302 10 false Battery Temperature Sensor 3 0.844,7.479 2.875,7.76 2.031,0.281 10 false Battery Temperature Sensor 4 0.833,8.417 2.865,8.646 2.031,0.229 10 false Battery Temperature Sensor 5 0.844,3.01 2.917,3.281 2.073,0.271 10 false Battery Temperature Sensor 0 5.375,8.635 5.833,8.833 0.458,0.198 10 false TB5 5.375,8.146 5.833,8.344 0.458,0.198 10 false GB5 5.365,7.698 5.823,7.896 0.458,0.198 10 false TB4 5.375,6.771 5.833,6.969 0.458,0.198 10 false TB3 5.375,7.208 5.833,7.406 0.458,0.198 10 false GB4 5.375,6.281 5.833,6.479 0.458,0.198 10 false GB3 5.385,5.094 5.844,5.292 0.458,0.198 10 false GB2 5.375,4.604 5.833,4.802 0.458,0.198 10 false TB2 5.385,4.156 5.844,4.354 0.458,0.198 10 false GB1 5.385,3.667 5.844,3.865 0.458,0.198 10 false TB1 5.385,3.208 5.844,3.406 0.458,0.198 10 false GB0 5.375,2.729 5.833,2.927 0.458,0.198 10 false TB0 4.25,8.625 4.708,8.823 0.458,0.198 10 false TB5 4.24,8.135 4.698,8.333 0.458,0.198 10 false GB5 4.24,7.688 4.698,7.885 0.458,0.198 10 false TB4 4.24,7.208 4.698,7.406 0.458,0.198 10 false GB4 4.24,6.76 4.698,6.958 0.458,0.198 10 false TB3 4.24,6.271 4.698,6.469 0.458,0.198 10 false GB3 4.26,4.604 4.719,4.802 0.458,0.198 10 false TB2 4.25,5.094 4.708,5.292 0.458,0.198 10 false GB2 4.25,3.667 4.708,3.865 0.458,0.198 10 false TB1 4.25,4.167 4.708,4.365 0.458,0.198 10 false GB1 4.25,2.74 4.708,2.938 0.458,0.198 10 false TB0 4.24,3.229 4.698,3.427 0.458,0.198 10 false GB0 3.813,2.74 4.271,2.938 0.458,0.198 10 false TB0 3.813,3.229 4.271,3.427 0.458,0.198 10 false GB0 3.802,3.677 4.26,3.875 0.458,0.198 10 false TB1 3.813,4.167 4.271,4.365 0.458,0.198 10 false GB1 3.813,4.604 4.271,4.802 0.458,0.198 10 false TB2 3.813,5.083 4.271,5.281 0.458,0.198 10 false GB2 5.156,2.729 5.333,2.948 0.177,0.219 10 false 6 5.115,3.208 5.427,3.406 0.313,0.198 10 false 26 5.104,3.677 5.417,3.875 0.313,0.198 10 false 25 5.156,4.167 5.313,4.365 0.156,0.198 10 false 5 5.167,4.594 5.323,4.792 0.156,0.198 10 false 4 5.115,5.094 5.427,5.292 0.313,0.198 10 false 24 4.615,2.729 4.771,2.927 0.156,0.198 10 false 2 4.615,3.229 4.771,3.427 0.156,0.198 10 false 7 4.625,3.677 4.781,3.875 0.156,0.198 10 false 8 4.635,4.167 4.792,4.365 0.156,0.198 10 false 3 4.625,4.604 4.781,4.802 0.156,0.198 10 false 4 4.635,5.094 4.792,5.292 0.156,0.198 10 false 9 3.604,5.083 3.76,5.281 0.156,0.198 10 false 9 3.594,4.594 3.75,4.792 0.156,0.198 10 false 4 3.594,4.167 3.75,4.365 0.156,0.198 10 false 3 3.615,3.667 3.771,3.865 0.156,0.198 10 false 8 3.594,3.229 3.75,3.427 0.156,0.198 10 false 7 3.594,2.729 3.75,2.927 0.156,0.198 10 false 2 4.635,6.271 4.792,6.469 0.156,0.198 10 false 2 3.615,6.25 3.771,6.448 0.156,0.198 10 false 2 3.604,6.75 3.781,6.958 0.177,0.208 10 false 7 4.635,6.771 4.813,6.979 0.177,0.208 10 false 7 3.604,7.198 3.76,7.396 0.156,0.198 10 false 8 4.635,7.219 4.792,7.417 0.156,0.198 10 false 8 3.594,7.688 3.75,7.885 0.156,0.198 10 false 3 4.635,7.708 4.792,7.906 0.156,0.198 10 false 3 3.583,8.135 3.74,8.333 0.156,0.198 10 false 4 4.635,8.156 4.792,8.354 0.156,0.198 10 false 4 3.563,8.615 3.719,8.813 0.156,0.198 10 false 9 4.646,8.635 4.802,8.833 0.156,0.198 10 false 9 5.156,6.271 5.313,6.469 0.156,0.198 10 false 3 5.104,6.771 5.417,6.969 0.313,0.198 10 false 23 5.115,7.219 5.427,7.417 0.313,0.198 10 false 22 5.177,7.708 5.333,7.906 0.156,0.198 10 false 2 5.177,8.146 5.333,8.344 0.156,0.198 10 false 1 5.115,8.635 5.427,8.833 0.313,0.198 10 false 21 5.375,9.427 6.948,9.677 1.573,0.25 10 false Battery ECU Assembly 5.083,9.427 5.417,9.615 0.333,0.188 10 false z26 1.5,0.25 3.188,0.448 1.688,0.198 10 false Battery Current Sensor 0.531,2.26 5.271,2.458 4.74,0.198 10 false No. 1 EV Battery Junction Block Assembly 3.813,6.271 4.271,6.469 0.458,0.198 10 false GB3 3.823,6.76 4.281,6.958 0.458,0.198 10 false TB3 3.813,7.208 4.271,7.406 0.458,0.198 10 false GB4 3.854,7.688 4.313,7.885 0.458,0.198 10 false TB4 3.823,8.135 4.281,8.333 0.458,0.198 10 false GB5 3.823,8.615 4.281,8.813 0.458,0.198 10 false TB5 3.427,5.573 5,5.917 1.573,0.344 10 false No. 1 EV Supply Stack Sub-assembly Connector 3.427,9.115 5,9.458 1.573,0.344 10 false No. 2 EV Supply Stack Sub-assembly Connector

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an EV supply battery assembly, make sure to return it through an authorized collection agent who is capable of handling it safely. If the EV supply battery assembly is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the EV supply battery assembly is disposed of improperly or abandoned. Therefore, make sure to return all EV supply battery assemblies through an authorized collection agent.


·

Before returning the EV supply battery assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the EV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the EV supply battery assembly and EV supply stack sub-assemblies.

·
A358020

After removing the EV supply battery assembly, keep it away from water. Exposure to water may cause the EV supply battery assembly to produce heat, resulting in a fire.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV BATTERY, EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV Battery > Trouble Codes
50001 398
Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11, P0ACA15, P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315 for Hybrid battery system is output A
P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11, P0ACA15, P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315 is output and DTCs other than the DTCs in the table below are output B
P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11, P0ACA15, P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315 is output and Hybrid battery system DTCs in the table below are output C
P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11, P0ACA15, P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315 is output and Hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK ODOMETER

B

2.CHECK ODOMETER

C

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

D

2.CHECK ODOMETER
a.

Check and record the total distance traveled of the vehicle.


Result:
Proceed to
NEXT



NEXT

3.READ VALUE USING GTS (HYBRID/EV BATTERY TEMPERATURE)
3.READ VALUE USING GTS (HYBRID/EV BATTERY TEMPERATURE)

Pre-procedure1

a.

None.


Procedure1

a.

Read the Data List.

Powertrain > EV Battery > Data List
Tester Display Measurement Item Range Reference Value Diagnostic Note
Hybrid/EV Battery Temperature 1 EV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid/EV Battery Temperature 2 EV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid/EV Battery Temperature 3 EV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid/EV Battery Temperature 4 EV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid/EV Battery Temperature 5 EV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid/EV Battery Temperature 6 EV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Powertrain > EV Battery > Data List
Tester Display
Hybrid/EV Battery Temperature 1
Hybrid/EV Battery Temperature 2
Hybrid/EV Battery Temperature 3
Hybrid/EV Battery Temperature 4
Hybrid/EV Battery Temperature 5
Hybrid/EV Battery Temperature 6
50003 398 62,63,64,65,66,67

HINT:

A malfunctioning sensor (battery temperature sensor 0, 1, 2, 3, 4 or 5) can be determined by comparing the output temperature of the 6 battery temperature sensors.


Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.CHECK FREEZE FRAME DATA
4.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

a.

Check and record the "Hybrid/EV Battery Current Sensor Power Supply Voltage" freeze frame data.

Powertrain > EV Battery > Trouble Codes
50001 398
HINT:

Use this for reference when measuring the EV battery current sensor power supply voltage.



Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

5.CHECK DTC
5.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
"P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11 or P0ACA15" is also output. A
"P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315" is also output. B



A

6.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EV SUPPLY STACK SUB-ASSEMBLY CONNECTOR)

B

13.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV SUPPLY STACK SUB-ASSEMBLY CONNECTOR)
6.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EV SUPPLY STACK SUB-ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 EV battery shield sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



Procedure1

a.
A479521N01
0.938,0.76 1.24,1.042 0.302,0.281 0.99,0.802 1.146,1 0.156,0.198 10 true A

Check the connections of the A No. 1 EV supply stack sub-assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the No. 2 EV battery shield sub-assembly.



OK

7.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



Procedure1

a.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Check the connections of the z26 battery ECU assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the upper No. 1 EV battery cover sub-assembly.



OK

8.CHECK EV BATTERY (BATTERY TEMPERATURE SENSOR 0 to 2)

NG

CONNECT SECURELY

8.CHECK EV BATTERY (BATTERY TEMPERATURE SENSOR 0 to 2)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374183C23
1.51,0.156 1.99,0.396 0.479,0.24 2.563,1.469 2.792,0.76 true 2.438,1.479 2.198,0.729 true 3.01,2.656 2.563,1.76 true 1.76,2.667 2.292,1.771 true 2.396,2.656 2.427,1.75 true 1.49,0.719 2.292,1.479 true 2.271,2.771 2.729,2.969 0.458,0.198 10 false TB1 2.792,0.542 3.25,0.74 0.458,0.198 10 false TB2 1.292,0.531 1.75,0.729 0.458,0.198 10 false TB0 2.073,0.542 2.531,0.74 0.458,0.198 10 false GB1 2.927,2.76 3.385,2.958 0.458,0.198 10 false GB2 1.594,2.771 2.052,2.969 0.458,0.198 10 false GB0 1.635,0.198 1.948,0.396 0.313,0.198 10 false z26 0.135,0.156 0.448,0.313 0.313,0.156 10 false *a
*a Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 2).

Tester Connection:
Tester Connection Battery Temperature Sensor

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-6 (TB0) - z26-26 (GB0) 0
z26-25 (TB1) - z26-5 (GB1) 1
z26-4 (TB2) - z26-24 (GB2) 2


Standard Resistance:
Thermistor Temperature Condition Specified Condition
0 to 10°C (32 to 50°F) Always 17.7 to 27.8 kΩ
10 to 20°C (50 to 68°F) Always 12.0 to 18.2 kΩ
20 to 30°C (68 to 86°F) Always 8.22 to 12.2 kΩ
30 to 40°C (86 to 104°F) Always 5.74 to 8.41 kΩ
40 to 50°C (104 to 122°F) Always 4.09 to 5.91 kΩ



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

9.CHECK EV BATTERY (BATTERY TEMPERATURE SENSOR 0 to 2)

NG

10.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 EV SUPPLY STACK SUB-ASSEMBLY)
9.CHECK EV BATTERY (BATTERY TEMPERATURE SENSOR 0 to 2)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374183C23
1.51,0.156 1.99,0.396 0.479,0.24 2.563,1.469 2.792,0.76 true 2.438,1.479 2.198,0.729 true 3.01,2.656 2.563,1.76 true 1.76,2.667 2.292,1.771 true 2.396,2.656 2.427,1.75 true 1.49,0.719 2.292,1.479 true 2.271,2.771 2.729,2.969 0.458,0.198 10 false TB1 2.792,0.542 3.25,0.74 0.458,0.198 10 false TB2 1.292,0.531 1.75,0.729 0.458,0.198 10 false TB0 2.073,0.542 2.531,0.74 0.458,0.198 10 false GB1 2.927,2.76 3.385,2.958 0.458,0.198 10 false GB2 1.594,2.771 2.052,2.969 0.458,0.198 10 false GB0 1.635,0.198 1.948,0.396 0.313,0.198 10 false z26 0.135,0.156 0.448,0.313 0.313,0.156 10 false *a
*a Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-6 (TB0) - Body ground and other terminals (except z26-26 (GB0)) Always 10 kΩ or higher
z26-26 (GB0) - Body ground and other terminals (except z26-6 (TB0)) Always 10 kΩ or higher
z26-25 (TB1) - Body ground and other terminals (except z26-5 (GB1)) Always 10 kΩ or higher
z26-5 (GB1) - Body ground and other terminals (except z26-25 (TB1)) Always 10 kΩ or higher
z26-4 (TB2) - Body ground and other terminals (except z26-24 (GB2)) Always 10 kΩ or higher
z26-24 (GB2) - Body ground and other terminals (except z26-4 (TB2)) Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

17.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 EV SUPPLY STACK SUB-ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 EV SUPPLY STACK SUB-ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A479521N01
0.938,0.76 1.24,1.042 0.302,0.281 0.99,0.802 1.146,1 0.156,0.198 10 true A

Disconnect the A No. 1 EV supply stack sub-assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.

Measure the resistance according to the value (s) in the table below.

A479523C01
1.583,0.542 1.969,0.844 0.385,0.302 4.25,1.26 4.646,1.573 0.396,0.313 2.271,1.313 2.375,0.396 true 2.385,1.313 2.781,0.417 true 2.479,1.313 3.24,0.417 true 2.292,2.354 2.26,1.552 true 2.76,2.333 2.365,1.552 true 3.281,2.333 2.479,1.542 true 5.396,1.375 5.833,0.833 true 5.292,1.365 5.417,0.833 true 5.188,1.365 4.833,0.833 true 5.833,2.083 5.385,1.552 true 5.417,2.083 5.292,1.552 true 4.833,2.083 5.167,1.542 true 2.25,0.219 2.708,0.417 0.458,0.198 10 false TB0 2.667,0.219 3.125,0.417 0.458,0.198 10 false GB1 3.146,0.208 3.604,0.406 0.458,0.198 10 false TB2 2.188,2.417 2.646,2.615 0.458,0.198 10 false GB0 2.677,2.417 3.135,2.615 0.458,0.198 10 false TB1 3.198,2.417 3.656,2.615 0.458,0.198 10 false GB2 1.667,0.615 2.125,0.813 0.458,0.198 10 false z26 0.625,0.177 0.938,0.375 0.313,0.198 10 false *a 4.354,0.24 4.667,0.438 0.313,0.198 10 false *b 4.625,0.667 5.083,0.865 0.458,0.198 10 false TB0 4.667,2.146 5.125,2.344 0.458,0.198 10 false GB0 5.292,2.156 5.75,2.354 0.458,0.198 10 false TB1 5.271,0.667 5.729,0.865 0.458,0.198 10 false GB1 5.792,0.677 6.25,0.875 0.458,0.198 10 false TB2 5.813,2.156 6.271,2.354 0.458,0.198 10 false TB1 4.406,1.354 4.563,1.552 0.156,0.198 10 false A
*a Rear view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to No. 1 EV Supply Stack Sub-assembly)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-6 (TB0) - A-2 (TB0) Always Below 1 Ω
z26-26 (GB0) - A-7 (GB0) Always Below 1 Ω
z26-25 (TB1) - A-8 (TB1) Always Below 1 Ω
z26-5 (GB1) - A-3 (GB1) Always Below 1 Ω
z26-4 (TB2) - A-4 (TB2) Always Below 1 Ω
z26-24 (GB2) - A-9 (GB2) Always Below 1 Ω


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-6 (TB0) or A-2 (TB0) - Body ground and other terminals Always 10 kΩ or higher
z26-26 (GB0) or A-7 (GB0) - Body ground and other terminals Always 10 kΩ or higher
z26-25 (TB1) or A-8 (TB1) - Body ground and other terminals Always 10 kΩ or higher
z26-5 (GB1) or A-3 (GB1) - Body ground and other terminals Always 10 kΩ or higher
z26-4 (TB2) or A-4 (TB2) - Body ground and other terminals Always 10 kΩ or higher
z26-24 (GB2) or A-9 (GB2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the A No. 1 EV supply stack sub-assembly connector.


b.

Reconnect the z26 battery ECU assembly connector.


c.

Install the upper No. 1 EV battery cover sub-assembly.



OK

11.CHECK TOTAL DISTANCE DRIVEN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

B

12.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
12.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

13.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV SUPPLY STACK SUB-ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 EV battery shield sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



Procedure1

a.
A479522N01
1.021,2.125 1.26,2.375 0.24,0.25 1.063,2.146 1.219,2.344 0.156,0.198 10 true B

Check the connections of the B No. 2 EV supply stack sub-assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the No. 2 EV battery shield sub-assembly.



OK

14.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

14.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



Procedure1

a.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Check the connections of the z26 battery ECU assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the upper No. 1 EV battery cover sub-assembly.



OK

15.CHECK EV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)

NG

CONNECT SECURELY

15.CHECK EV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374183C24
1.51,0.156 1.885,0.396 0.375,0.24 2.969,1.458 2.938,0.781 true 2.813,1.469 2.49,0.76 true 3.01,2.656 2.969,1.75 true 1.76,2.667 2.677,1.76 true 2.396,2.656 2.823,1.771 true 1.823,0.75 2.646,1.469 true 2.271,2.771 2.729,2.969 0.458,0.198 10 false GB4 2.792,0.542 3.25,0.74 0.458,0.198 10 false GB5 1.656,0.573 2.115,0.771 0.458,0.198 10 false GB3 2.313,0.552 2.771,0.75 0.458,0.198 10 false TB4 2.927,2.76 3.385,2.958 0.458,0.198 10 false TB5 1.594,2.771 2.052,2.969 0.458,0.198 10 false TB3 1.583,0.198 1.896,0.396 0.313,0.198 10 false z26 0.135,0.156 0.448,0.313 0.313,0.156 10 false *a
*a Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 3 to 5).

Tester Connection:
Tester Connection Battery Temperature Sensor

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-23 (TB3) - z26-3 (GB3) 3
z26-2 (TB4) - z26-22 (GB4) 4
z26-21 (TB5) - z26-1 (GB5) 5


Standard Resistance:
Thermistor Temperature Condition Specified Condition
0 to 10°C (32 to 50°F) Always 17.7 to 27.8 kΩ
10 to 20°C (50 to 68°F) Always 12.0 to 18.2 kΩ
20 to 30°C (68 to 86°F) Always 8.22 to 12.2 kΩ
30 to 40°C (86 to 104°F) Always 5.74 to 8.41 kΩ
40 to 50°C (104 to 122°F) Always 4.09 to 5.91 kΩ



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

16.CHECK EV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)

NG

20.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV SUPPLY STACK SUB-ASSEMBLY)
16.CHECK EV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C374183C24
1.51,0.156 1.885,0.396 0.375,0.24 2.969,1.458 2.938,0.781 true 2.813,1.469 2.49,0.76 true 3.01,2.656 2.969,1.75 true 1.76,2.667 2.677,1.76 true 2.396,2.656 2.823,1.771 true 1.823,0.75 2.646,1.469 true 2.271,2.771 2.729,2.969 0.458,0.198 10 false GB4 2.792,0.542 3.25,0.74 0.458,0.198 10 false GB5 1.656,0.573 2.115,0.771 0.458,0.198 10 false GB3 2.313,0.552 2.771,0.75 0.458,0.198 10 false TB4 2.927,2.76 3.385,2.958 0.458,0.198 10 false TB5 1.594,2.771 2.052,2.969 0.458,0.198 10 false TB3 1.583,0.198 1.896,0.396 0.313,0.198 10 false z26 0.135,0.156 0.448,0.313 0.313,0.156 10 false *a
*a Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-23 (TB3) - Body ground and other terminals (except z26-3 (GB3)) Always 10 kΩ or higher
z26-3 (GB3) - Body ground and other terminals (except z26-23 (TB3)) Always 10 kΩ or higher
z26-2 (TB4) - Body ground and other terminals (except z26-22 (GB4)) Always 10 kΩ or higher
z26-22 (GB4) - Body ground and other terminals (except z26-2 (TB4)) Always 10 kΩ or higher
z26-21 (TB5) - Body ground and other terminals (except z26-1 (GB5)) Always 10 kΩ or higher
z26-1 (GB5) - Body ground and other terminals (except z26-21 (TB5)) Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

17.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

20.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV SUPPLY STACK SUB-ASSEMBLY)
17.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
C371962N08
1.563,0.469 1.99,0.729 0.427,0.26 1.635,0.5 1.927,0.688 0.292,0.188 10 true z23

Disconnect the z23 battery current sensor connector from the No. 1 EV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
C373318C12
1.49,1.688 1.875,1.896 0.385,0.208 1.5,0.135 1.885,0.344 0.385,0.208 1.792,0.958 2.302,0.531 true 1.792,1.156 2.417,1.156 true 1.604,0.99 1.073,0.583 true 0.698,2.365 0.469,1.927 true 0.469,3.063 0.833,2.604 true 0.823,2.375 1.021,1.875 true 0.865,3.063 0.958,2.594 true 0.979,1.156 1.604,1.156 true 1.594,0.177 1.906,0.375 0.313,0.198 10 false z23 1.583,1.729 1.896,1.927 0.313,0.198 10 false z26 0.25,1.781 0.708,1.979 0.458,0.198 10 false VIB 0.792,0.479 1.25,0.677 0.458,0.198 10 false VIB 0.292,3.115 0.75,3.313 0.458,0.198 10 false IB1 2.427,0.417 2.885,0.615 0.458,0.198 10 false IB1 0.76,3.104 1.219,3.302 0.458,0.198 10 false GIB 0.677,1.094 1.135,1.292 0.458,0.198 10 false GIB 2.531,1.083 2.99,1.281 0.458,0.198 10 false IB0 0.979,1.677 1.438,1.875 0.458,0.198 10 false IB0 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.104,1.479 0.417,1.635 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 1 EV Battery Junction Block Assembly (Battery Current Sensor))
*b Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(z26,z23)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

Click Connector(z23)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z26-19 (VIB) - z23-1 (VIB) Always Below 1 Ω
z26-38 (IB1) - z23-2 (IB1) Always Below 1 Ω
z26-37 (GIB) - z23-3 (GIB) Always Below 1 Ω
z26-18 (IB0) - z23-4 (IB0) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(z26,z23)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

Click Connector(z23)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z26-19 (VIB) or z23-1 (VIB) - Body ground and other terminals Always 10 kΩ or higher
z26-38 (IB1) or z23-2 (IB1) - Body ground and other terminals Always 10 kΩ or higher
z26-37 (GIB) or z23-3 (GIB) - Body ground and other terminals Always 10 kΩ or higher
z26-18 (IB0) - z23-4 (IB0) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z23 battery current sensor connector to the No. 1 EV battery junction block assembly.


b.

Reconnect the z26 battery ECU assembly connector.


c.

Install the upper No. 1 EV battery cover sub-assembly.



OK

18.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373319C08
1.521,2.688 1.979,2.958 0.458,0.271 0.573,3.042 1.74,3.823 true 2.5,3.594 2.927,2.99 true 0.125,0.156 0.354,0.333 0.229,0.177 10 true *a 1.583,2.74 2.042,2.938 0.458,0.198 10 false G156 0.25,2.875 0.615,3.052 0.365,0.177 10 false IGCT 2.958,2.823 3.354,3.021 0.396,0.198 10 false GND
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Apply auxiliary battery voltage between No. 2 EV battery pack wire connector terminals G156-14 (IGCT) - G156-1 (GND).

NOTICE:

Make sure that the battery positive and battery negative do not contact one another.



Procedure1

a.
C371921C11
1.531,1.51 1.896,1.75 0.365,0.24 0.323,1.635 0.521,2.344 true 0.813,2.656 0.5,3.146 true 0.115,0.115 0.427,0.271 0.313,0.156 10 false *a 0.198,1.438 0.656,1.635 0.458,0.198 10 false VIB 0.26,3.115 0.719,3.313 0.458,0.198 10 false GIB 1.594,1.552 1.896,1.76 0.302,0.208 10 false z26
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-19 (VIB) - z26-37 (GIB) Auxiliary battery positive (+) → G156-14 (IGCT)
Auxiliary battery negative (-) → G156-1 (GND)
4.6 to 5.4 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the G156 No. 2 EV battery pack wire connector from the auxiliary battery.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

NG

19.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
19.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper EV battery cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C371962N08
1.563,0.469 1.99,0.729 0.427,0.26 1.635,0.5 1.927,0.688 0.292,0.188 10 true z23

Disconnect the z23 battery current sensor connector from the No. 1 EV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
C373319C08
1.521,2.688 1.979,2.958 0.458,0.271 0.573,3.042 1.74,3.823 true 2.5,3.594 2.927,2.99 true 0.125,0.156 0.354,0.333 0.229,0.177 10 true *a 1.583,2.74 2.042,2.938 0.458,0.198 10 false G156 0.25,2.875 0.615,3.052 0.365,0.177 10 false IGCT 2.958,2.823 3.354,3.021 0.396,0.198 10 false GND
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Apply auxiliary battery voltage between No. 2 EV battery pack wire connector terminals G156-14 (IGCT) - G156-1 (GND).

NOTICE:

Make sure that the battery positive and battery negative do not contact one another.



Procedure1

a.
A479524C01
2.333,1.135 2.729,1.365 0.396,0.229 1.573,1.146 0.99,0.906 true 1,1.771 1.573,1.458 true 0.729,0.823 1.063,1.063 0.333,0.24 10 false VIB 0.729,1.719 1.094,1.969 0.365,0.25 10 false GIB 0.188,0.146 0.427,0.292 0.24,0.146 10 false *a 2.427,1.167 2.802,1.469 0.375,0.302 10 false z23
*a Front view of wire harness connector
(to No. 1 EV Battery Junction Block Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z23)Location & Routing

Click Connector(z23)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z23-1(VIB) - z23-3 (GIB) Auxiliary battery positive (+) → G156-14 (IGCT)
Auxiliary battery negative (-) → G156-1 (GND)
4.6 to 5.4 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Disconnect the G156 No. 2 EV battery pack wire connector from the auxiliary battery.


b.

Reconnect the z23 battery current sensor connector to the No. 1 EV battery junction block assembly.


c.

Install the upper EV battery cover panel.



OK

REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NG

20.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV SUPPLY STACK SUB-ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A479522N01
1.021,2.125 1.26,2.375 0.24,0.25 1.063,2.146 1.219,2.344 0.156,0.198 10 true B

Disconnect the B No. 2 EV supply stack sub-assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.

Measure the resistance according to the value (s) in the table below.

A479523C02
1.583,0.542 1.969,0.844 0.385,0.302 4.25,1.26 4.646,1.573 0.396,0.313 2.594,1.302 2.375,0.396 true 2.719,1.323 2.781,0.417 true 2.823,1.313 3.24,0.417 true 2.292,2.354 2.583,1.552 true 2.76,2.333 2.698,1.552 true 3.281,2.333 2.813,1.542 true 5.396,1.375 5.833,0.833 true 5.292,1.365 5.417,0.833 true 5.188,1.365 4.833,0.833 true 5.833,2.083 5.385,1.552 true 5.417,2.083 5.292,1.552 true 4.833,2.083 5.167,1.542 true 2.25,0.219 2.708,0.417 0.458,0.198 10 false GB3 2.667,0.219 3.125,0.417 0.458,0.198 10 false TB4 3.146,0.208 3.604,0.406 0.458,0.198 10 false GB5 2.188,2.417 2.646,2.615 0.458,0.198 10 false TB3 2.677,2.417 3.135,2.615 0.458,0.198 10 false GB4 3.198,2.417 3.656,2.615 0.458,0.198 10 false TB5 1.667,0.615 2.125,0.813 0.458,0.198 10 false z26 0.625,0.177 0.938,0.375 0.313,0.198 10 false *a 4.354,0.24 4.667,0.438 0.313,0.198 10 false *b 4.625,0.667 5.083,0.865 0.458,0.198 10 false GB3 4.667,2.146 5.125,2.344 0.458,0.198 10 false TB3 5.292,2.156 5.75,2.354 0.458,0.198 10 false GB4 5.271,0.667 5.729,0.865 0.458,0.198 10 false TB4 5.792,0.677 6.25,0.875 0.458,0.198 10 false GB5 5.813,2.156 6.271,2.354 0.458,0.198 10 false TB5 4.406,1.354 4.563,1.552 0.156,0.198 10 false B
*a Rear view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to No. 2 EV Supply Stack Sub-assembly)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-23 (TB3) - B-7 (TB3) Always Below 1 Ω
z26-3 (GB3) - B-2 (GB3) Always Below 1 Ω
z26-2 (TB4) - B-3 (TB4) Always Below 1 Ω
z26-22 (GB4) - B-8 (GB4) Always Below 1 Ω
z26-21 (TB5) - B-9 (TB5) Always Below 1 Ω
z26-1 (GB5) - B-4 (GB5) Always Below 1 Ω


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

z26-23 (TB3) or B-7 (TB3) - Body ground and other terminals Always 10 kΩ or higher
z26-3 (GB3) or B-2 (GB3) - Body ground and other terminals Always 10 kΩ or higher
z26-2 (TB4) or B-3 (TB4) - Body ground and other terminals Always 10 kΩ or higher
z26-22 (GB4) or B-8 (GB4) - Body ground and other terminals Always 10 kΩ or higher
z26-21 (TB5) or B-9 (TB5) - Body ground and other terminals Always 10 kΩ or higher
z26-1 (GB5) or B-4 (GB5) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the B No. 2 EV supply stack sub-assembly connector.


b.

Reconnect the z26 battery ECU assembly connector.


c.

Install the upper No. 1 EV battery cover sub-assembly.



OK

21.CHECK TOTAL DISTANCE DRIVEN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

B

22.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
22.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK