Home › BRAKE › PARKING BRAKE › PARKING BRAKE CABLE

PARKING BRAKE CABLE > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the No. 2 and No. 3 parking brake cable assembly.
  2. The procedures listed below are for the No. 3 parking brake cable assembly.



1. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
  1. Connect the No. 3 parking brake cable to the parking brake equalizer.



  1. Install the No. 3 parking brake cable with the bolts and button.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf } (Bolt A)
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf } (Bolt B)



    G028425E02



    G029315E01
  1. Install the No. 3 parking brake cable to the backing plate with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



2. INSTALL PARKING BRAKE CABLE HEAT INSULATOR
  1. Install the parking brake heat insulator with the 2 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



3. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A111834
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    40.5 mm (1.594 in.)

    If the length is less than the minimum, replace the compression spring.



    A076194E04
  1. Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Tap in the gasket in the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the exhaust pipe.

  1. Connect the 2 exhaust pipe supports, and install the exhaust pipe.

  1. Install the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



4. INSTALL FRONT FLOOR PANEL BRACE


    A086201
  1. Install the floor panel brace with the 2 bolts.

    Torque:
    30 N*m{ 302 kgf*cm , 22 ft.*lbf }



5. INSTALL HEATED OXYGEN SENSOR


A087474E01
  1. Using SST, install the sensor.

    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 32 in.*lbf } for use with SST
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use without SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

  1. Install the wire harness clamp bracket to the sensor.

  1. Install the grommet of the sensor to the vehicle.

  1. Connect the sensor connector.

  1. Install the floor carpet front with the clip.



6. APPLY HIGH TEMPERATURE GREASE


    F101065E02
  1. Apply high temperature grease to the shoe attached surface of the backing plate.



7. INSTALL REAR BRAKE PARKING BRAKE SHOE LEVER SUB-ASSEMBLY


    F101078
  1. Using needle-nose pliers, install the parking brake lever with a new C-washer.



8. INSTALL REAR BRAKE SHOE


    F045648E01
  1. Using needle-nose pliers, connect the No. 3 parking brake cable to the parking brake shoe lever.



    F045280E03
  1. Using SST, install the rear brake shoe, pin, shoe hold down spring and cup.

    SST
    09718-00010  



9. INSTALL REAR BRAKE SHOE RETURN SPRING
  1. Install the rear brake shoe return spring to the rear brake shoe.



10. INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER LH


    F101060
  1. Install the rear brake automatic adjust lever and the rear brake automatic adjust lever tension spring to the front brake shoe.



11. INSTALL PARKING BRAKE SHOE STRUT SET LH


    F101064E02
  1. Apply high temperature grease to the adjusting bolt and assemble the strut set.

  1. Install the shoe return spring to the strut set.



    F101079E01
  1. Install the strut set as shown in the illustration.



12. INSTALL FRONT BRAKE SHOE


    F045279E03
  1. Connect the tension spring to the front brake shoe and rear brake shoe.

  1. Using SST, install the front brake shoe, pin, shoe hold down spring and cup.

    SST
    09718-00010  



13. CONNECT PARKING BRAKE SHOE STRUT SET LH


    F045278E03
  1. Using SST, connect the shoe return spring to the front brake shoe and rear brake shoe.

    SST
    09703-30011  

    NOTICE:
    Be careful not to damage the wheel cylinder boot.



14. CHECK REAR DRUM BRAKE INSTALLATION


  1. Check that each part is installed properly.

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and drum.

    If they are not installed correctly as shown in the illustration, reinstall them.


    F040022E03



    F045281E01
  1. Measure the brake drum inside diameter and the diameter of the brake shoes. Check that the difference between the diameter is the correct shoe clearance.

    Standard shoe clearance:
    0.6 mm (0.024 in.)

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and the drum.



15. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY
  1. Aligning the matchmarks, install the rear brake drum.



16. ADJUST REAR DRUM BRAKE SHOE CLEARANCE


    F040023E04
  1. Temporarily install 2 hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.

  1. Rotate the adjuster by 8 notches.

  1. Install the hole plug.

  1. Remove the 2 hub nuts.



17. INSTALL REAR WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



18. INSPECT AND ADJUST PARKING BRAKE PEDAL TRAVEL
  1. Inspect and adjust the parking brake pedal travel (Click here).



19. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the problem areas to stop the leak. Replace damaged parts as necessary.


20. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY


    G028424E01
  1. Pass the No. 1 parking brake cable through the pedal bracket and hold it with a new clip.

  1. Pass the parking brake cable through the pedal guide. Temporarily tighten the adjusting nut and lock nut.

    HINT:
    Fully tighten the adjusting nut and lock nut when adjusting the parking brake pedal free play.

  1. Bend the parking brake pedal claw fully.



21. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    G028422E01
  1. Install the parking brake control pedal with the 2 bolts and nut.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the parking brake switch connector and install the harness clamp to the pedal bracket.



    G028420E01
  1. Connect the No. 1 parking brake cable to the parking brake intermediate lever.

  1. Install the No. 1 parking brake cable on the floor with the 2 bolts labeled A shown in the illustration.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



    G028419E01
  1. Install the No. 1 parking brake cable to the floor with the clamp bolt.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



  1. Install the 2 No. 1 parking brake cable clamp nuts and a new parking brake front cable clamp.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



    G028431E01



22. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET


    G028423E02
  1. Install the No. 1 front floor side reinforcement with the 2 bolts.

  1. Install the No. 1 console box mounting bracket with the 2 bolts.



23. INSTALL YAW RATE SENSOR (w/ VSC)


    F046182E01
  1. Install the sensor with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Connect the sensor connector.



24. INSTALL CENTER AIRBAG SENSOR ASSEMBLY


H043784E03
  1. Install the airbag sensor with the 3 bolts.

    Torque:
    17.5 N*m{ 178 kgf*cm , 13 ft.*lbf }

    CAUTION:
    1. If the airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Connect the airbag sensor connectors.



25. INSTALL FRONT FLOOR FOOTREST
  1. Attach the 2 clips to install the front floor footrest.



26. INSTALL FRONT SEAT ASSEMBLY LH/RH
  1. Install the front seat LH/RH (Click here).



27. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
  1. Install the instrument panel reinforcement with the 7 bolts.



  1. Install the 2 nuts to the air conditioning unit and temporarily tighten them.


    I038973E01



  1. Connect each connector and install each clamp. Then connect the wire harness.


    I038978E04



28. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    I039536E01
  1. Install the instrument panel brace with the 2 bolts and nut.

  1. Attach the clamp to connect the harness.



29. FULLY TIGHTEN AIR CONDITIONING UNIT ASSEMBLY


    I040423E04
  1. Fully tighten the air conditioning unit with the 2 nuts.

    NOTICE:
    Tighten the nuts in the order indicated in the illustration.



30. INSTALL STEERING COLUMN ASSEMBLY


    F046713E01
  1. Install the steering column with the 3 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the connectors and wire harness clamps to the steering column.



31. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the instrument panel.

  1. Connect all the connectors and attach all the clamps.

  1. Install the 2 screws.

  1. Install the 6 bolts.



  1. Install the 8 clips to the duct and lower instrument panel.


    B074066E06



32. INSTALL SHIFT LEVER ASSEMBLY


    G021871E01
  1. Connect the 2 connectors to the shift lever.

  1. Install the shift lever with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



33. INSTALL POWER STEERING ECU


G028403E01
  1. Install the ECU with the 3 screws.

    Torque:
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf }



    G028402E01
  1. Connect the 4 ECU connectors.

  1. Install the torque sensor wire harness clamp to the ECU.



34. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the instrument panel (Click here).

    HINT:
    Refer to the procedures from the installation of the instrument panel sub-assembly up until the installation of the No. 1 instrument panel register assembly.



35. INSTALL COOLER REFRIGERANT LIQUID PIPE E (TO COOLER UNIT)
  1. Remove the attached vinyl tape from the pipe's disconnected part.

  1. Sufficiently apply compressor oil (ND-OIL 11) to 2 new O-rings and the pipe's connecting part.

    NOTICE:
    1. Do not use any compressor oil other than ND-OIL 11.
    2. If any compressor oil other than ND-OIL 11 is used, compressor motor insulation performance may decrease, resulting in a leakage of electric power.

  1. Install the O-rings to the pipe.

  1. Insert the pipe joint into the cooler unit fitting hole securely.



    I006878E08
  1. Using the piping clamp, connect the cooler unit refrigerant liquid pipe E.

    NOTICE:
    Ensure that the piping clamp is securely engaged.



36. INSTALL SUCTION HOSE SUB-ASSEMBLY

HINT:
Use the same procedures described for the cooler unit refrigerant liquid pipe E.



37. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the refrigerant gas, inspect for refrigerant leak gas using a halogen leak detector.

  1. After recharging the refrigerant gas, prepare the vehicle for a refrigerant gas leakage check by making sure the following conditions are met.

    1. The ignition switch is OFF.

    2. The vehicle is in a place with good air ventilation and without any volatile gases, such as evaporated gasoline or exhaust gas. The detector is very sensitive to volatile gases. If volatile gases are unavoidable, the vehicle must be lifted up.

    3. Some refrigerant remains in the refrigerant system.

    4. The compressor is OFF and its pressure is approximately 392 to 588 kPa (4 to 6 kgf/cm2).



    N014519E04
  1. Bring the gas leak detector close to the drain hose with the detector's power off.

    HINT:
    1. After the blower motor has stopped, leave the cooling unit as it is for more than 15 minutes.
    2. Expose the gas leak detector sensor under the drain hose.
    3. When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to the volatile gases.

  1. If a gas leak is not detected on the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and wait for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.



38. POSITION SPIRAL CABLE SUB-ASSEMBLY


H043750E02
  1. Slowly rotate the spiral cable counterclockwise by hand until it feels firm.

    NOTICE:
    Do not use the airbag wire harness to turn the spiral cable.



    H043751E02
  1. Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not use the airbag wire harness to turn the spiral cable.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to the left and right from the center.



39. INSTALL STEERING COLUMN COVER
  1. Engage the 4 claws to install the steering column upper cover and steering column lower cover.

    HINT:
    Fully tilt down the steering column when installing the steering column upper cover and fully tilt it up when installing the steering column cover.



40. INSTALL TILT LEVER BRACKET
  1. Install the tilt level bracket with the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



41. INSTALL STEERING WHEEL ASSEMBLY
  1. Align the matchmarks on the steering wheel and steering main shaft.

  1. Install the steering wheel with the set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



42. INSTALL STEERING PAD ASSEMBLY


H043738E03
  1. Support the steering pad with one hand as shown in the illustration.

  1. Connect the 2 airbag connectors.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Connect the horn connector.

  1. Install the steering pad after confirming that the circumference grooves of the screws are caught on the screw case.

  1. Using a T30 "TORX" socket, install the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



43. INSPECT STEERING PAD ASSEMBLY
  1. Check for cuts, cracks or discoloration on the steering pad outer surface and in the grooved portion.

  1. Check that the horn sounds.



44. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



45. INSTALL REAR NO. 3 FLOOR BOARD


    A088355E02
  1. Install the floor board, and then attach the 4 claws.



46. INSTALL REAR DECK FLOOR BOX


    A088354E01
  1. Install the rear deck floor box to the vehicle.



47. INSTALL REAR NO. 2 FLOOR BOARD


    A088353E01
  1. Install the floor board, and then lock the 2 cover knobs.



48. ADD ENGINE COOLANT


49. CHARGE REFRIGERANT
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Amount:
    450 +-30 g (15.9 +-1.1 oz.)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)


    I030082E09

    NOTICE:
    1. Do not turn the A/C on before charging refrigerant as the cooler compressor does not work properly without any refrigerant. Operating without any refrigerant causes it to overheat.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.

    HINT:
    Prepare a service can to recharge the refrigerant if using the refrigerant gas collected with the Freon collection/recycling device because the collective rate of the device is approximately 90%.



50. INSPECT FOR ENGINE COOLANT LEAK


51. WARM UP ENGINE


52. INSPECT AND ADJUST PARKING BRAKE PEDAL TRAVEL
  1. Inspect and adjust the parking brake pedal travel (Click here).



53. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).



54. PERFORM TORQUE SENSOR ZERO POINT CALIBRATION
  1. Perform the torque sensor zero point calibration (Click here).