Home › HYBRID SYSTEM › HYBRID TRANSMISSION / TRANSAXLE › HYBRID VEHICLE TRANSAXLE

HYBRID VEHICLE TRANSAXLE > REMOVAL

for Preparation Click here


CAUTION:
  1. When working on the high voltage systems, always wear insulated gloves.
  2. Keep the removed service plug in your pocket to prevent other technicians from reconnecting it while you are servicing the vehicle.
  3. After removing the service plug grip, do not touch the high voltage connectors and terminals for 5 minutes.

NOTICE:
After removing the service plug grip, do not operate the power switch as it may damage the hybrid vehicle control ECU.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE SERVICE PLUG GRIP
  1. Remove the service plug grip (Click here).



3. REMOVE FRONT WHEEL


4. REMOVE ENGINE UNDER COVER LH


5. REMOVE ENGINE UNDER COVER RH


6. DRAIN COOLANT (for Inverter)
  1. Drain the coolant .



7. DRAIN TRANSAXLE OIL
  1. Drain the transaxle oil .



8. REMOVE HOOD SUB-ASSEMBLY
  1. Remove the hood (Click here).



9. REMOVE FRONT WIPER ARM LH
  1. Remove the front wiper arm LH .



10. REMOVE FRONT WIPER ARM RH
  1. Remove the front wiper arm RH .



11. REMOVE COWL TOP FRONT PANEL SUB-ASSEMBLY OUTER
  1. Remove the cowl top front panel (Click here).



12. REMOVE INVERTER WITH CONVERTER ASSEMBLY
  1. Remove the inverter with converter .



13. REMOVE AIR CLEANER ASSEMBLY
  1. Remove the air cleaner .



14. DISCONNECT WIRE HARNESS


    G030089E01
  1. Disconnect the 3 connectors shown in the illustration and the clamp.



    C098456E01
  1. Disconnect the 2 clamps shown in the illustration.



    C098379E02
  1. Disconnect the connector.

  1. Remove the 3 bolts and transmission case cover from the hybrid vehicle transaxle.



    Z035713E01
  1. Disconnect the 2 clamps.



    C098457E01
  1. Remove the bolt and ground wire.



15. DISCONNECT NO. 4 INVERTER COOLING HOSE


    C097764E01
  1. Remove the 4 clamps and disconnect the 3 hoses.



16. REMOVE FRONT DRIVE SHAFT ASSEMBLY
  1. Remove the front drive shaft (Click here).



17. DISCONNECT EXHAUST PIPE ASSEMBLY
  1. Disconnect the exhaust pipe (Click here).



18. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    A088033E01
  1. Remove the 4 bolts and 2 nuts, then remove the engine moving control rod with bracket.



    A088034E01
  1. Remove the 4 bolts, then remove the front suspension crossmember with power steering gear assembly.



19. SUSPEND ENGINE ASSEMBLY


    D025372E01
  1. Disconnect the 2 PCV hoses.

  1. Install the No. 1 and No. 2 engine hangers in the correct direction.

    Parts No.:
    No. 1 engine hanger:
    12281-22021
    No. 2 engine hanger:
    12281-15040
    Bolt:
    91512-B1016

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Attach an engine chain hoist to the engine hangers.

    CAUTION:
    Do not attempt to hang the engine by hooking the chain to any other parts.



20. SUPPORT HYBRID VEHICLE TRANSAXLE ASSEMBLY
  1. Using a transmission jack, support the hybrid vehicle transaxle.



21. DISCONNECT NO. 3 ENGINE MOUNTING BRACKET


    C098372E01
  1. Remove the nut and disconnect the engine mounting bracket from the engine mounting insulator.



22. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY


    G030261E01
  1. Remove the 2 bolts, starter cover and housing side cover.



    G031001E01
  1. Remove the 6 bolts and hybrid vehicle transaxle.

    NOTICE:
    To avoid damage to the knock pin, do not pry the connecting portion of the HV transaxle and the engine.



23. REMOVE NO. 6 INVERTER COOLING HOSE


    C098448E01
  1. Remove the clamp and inverter cooling hose.



24. REMOVE NO. 3 ENGINE MOUNTING BRACKET


    C098374E01
  1. Remove the 3 bolts and engine mounting bracket.



    C098449E01
  1. Remove the 6 bolts shown in the illustration and clamp.