Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM J

1NZ-FXE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the start request signal output from the power management control ECU is input to the ECM, and the NE signal generated by the crank position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump with filter assembly operates.

While the NE signal is input to the ECM with the engine running, the ECM turns Tr1 on continuously.

WIRING DIAGRAM

A275905E01
1.231,2.994 1.512,3.148 0.282,0.154 10 P/I 2.297,7.349 2.692,7.498 0.394,0.149 10 M22 2.297,7.503 3.278,7.814 0.981,0.311 10 Fuel Pump with Filter Assembly 0.756,7.524 1.376,7.923 0.620,0.399 10 Auxiliary Battery 3.03,6.862 4.655,7.032 1.625,0.170 10 No. 1 Integration Relay 3.314,4.825 4.033,4.978 0.720,0.154 10 EFI-MAIN 4.691,2.847 4.886,2.999 0.195,0.152 10 2D 4.732,2.666 4.832,2.818 0.100,0.152 10 4 2.118,2.839 2.318,2.991 0.200,0.152 10 2E 2.168,2.657 2.268,2.809 0.100,0.152 10 1 2.118,3.18 2.318,3.332 0.200,0.152 10 2D 2.161,3.013 2.261,3.165 0.100,0.152 10 2 2.118,4.501 2.318,4.653 0.200,0.152 10 2C 2.168,4.319 2.268,4.471 0.100,0.152 10 2 3.358,6.313 3.816,6.465 0.458,0.152 10 C/OPN 4.674,4.136 4.874,4.287 0.200,0.152 10 2C 4.723,3.957 4.823,4.109 0.100,0.152 10 4 5.999,6.457 6.212,6.609 0.212,0.152 10 FC 5.74,6.457 5.915,6.609 0.175,0.152 10 21 6.011,4.487 6.422,4.639 0.410,0.152 10 MREL 5.752,4.401 5.927,4.553 0.175,0.152 10 46 6.353,7.695 6.687,7.846 0.334,0.152 10 ECM 6.05,7.695 6.315,7.846 0.264,0.152 10 A40 3.966,2.295 4.161,2.446 0.195,0.152 10 2D 3.918,2.095 4.018,2.247 0.100,0.152 10 3 2.021,7.034 2.121,7.186 0.100,0.152 10 4 2.021,7.966 2.121,8.118 0.100,0.152 10 5 2.021,7.756 2.142,7.907 0.121,0.152 10 E 2.021,7.237 2.142,7.389 0.121,0.152 10 B 4.813,0.446 4.913,0.597 0.100,0.152 10 2 4.998,0.53 5.341,0.681 0.343,0.152 10 IG2D 5.064,1.049 5.337,1.201 0.274,0.152 10 A39 5.064,1.217 6.404,1.605 1.340,0.387 10 Power Management Control ECU 6.616,5.878 6.856,6.030 0.240,0.152 10 Tr1 0.611,6.002 0.987,6.156 0.376,0.154 10 MAIN 3.453,3.493 3.707,3.645 0.254,0.152 10 IG2 5.026,2.982 5.516,3.342 0.490,0.360 10 IG2 NO. 2 2.867,2.987 3.121,3.139 0.254,0.152 10 IG2 4.674,4.511 4.874,4.663 0.200,0.152 10 2C 4.728,4.332 4.828,4.484 0.100,0.152 10 3 2.657,4.278 3.377,4.432 0.720,0.154 10 EFI-MAIN 2.107,5.572 2.307,5.724 0.200,0.152 10 2D 2.162,5.393 2.262,5.545 0.100,0.152 10 8 4.676,5.584 4.876,5.735 0.200,0.152 10 2D 4.727,5.4 4.827,5.552 0.100,0.152 10 5 4.676,5.995 4.876,6.147 0.200,0.152 10 2D 4.727,5.811 4.827,5.963 0.100,0.152 10 6 4.676,6.544 4.876,6.696 0.200,0.152 10 2D 4.727,6.364 4.827,6.516 0.100,0.152 10 7

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

Check whether the fuel pump with filter assembly operating sound occurs when performing the Active Test on the tester.

Result
Result Proceed to
Fuel pump with filter assembly operating sound does not occur A
Fuel pump with filter assembly operating sound occurs B



A

2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

B

7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-7 - A40-21 (FC) Always Below 1 Ω
2D-7 or A40-21 (FC) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP WITH FILTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP WITH FILTER ASSEMBLY)
a.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the fuel pump with filter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-8 - M22-4 (B) Always Below 1 Ω
2D-8 or M22-4 (B) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP WITH FILTER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP WITH FILTER ASSEMBLY - BODY GROUND)
a.

Disconnect the fuel pump with filter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M22-5 (E) - Body ground Always Below 1 Ω




OK

5.INSPECT FUEL PUMP WITH FILTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL PUMP WITH FILTER ASSEMBLY
a.

Inspect the fuel pump with filter assembly (See page Engine / Hybrid System>1NZ-FXE FUEL>FUEL PUMP>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel pump with filter assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

6.INSPECT NO.1 INTEGRATION RELAY (C/OPN RELAY)

NG

REPLACE FUEL PUMP WITH FILTER ASSEMBLY

6.INSPECT NO.1 INTEGRATION RELAY (C/OPN RELAY)
a.

Inspect the No. 1 integration relay (C/OPN relay) (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>INTEGRATION RELAY>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 INTEGRATION RELAY)

NG

7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.


f.

Check the result when the power switch on (IG) and the engine starts.

OK
Condition Starter Signal
Power switch on (IG) Close (OFF)
Engine started Open (ON)



OK

8.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

NG

8.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.


f.

Read the values displayed on the tester while cranking.

OK:

Values are displayed continuously.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG