Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module)
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM(w/o Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0335  Crankshaft Position Sensor "A" Circuit  


DESCRIPTION

The crank position sensor system consists of a crank angle sensor plate and a pickup coil.

The crank angle sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The crank angle sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection and ignition timing are controlled.

DTC No. DTC Detection Condition Trouble Area
P0335 Either of the following conditions is met (1 trip detection logic):
·

No crank position sensor signal to ECM while engine running.

·

Missing crank position sensor signal despite cam position sensor signal inputs normal after engine cranked.


·

Open or short in crank position sensor circuit

·

Crank position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM



A390144E01
2.802,0.594 3.26,0.792 0.458,0.198 10 false GND 2.802,1.417 3.26,1.615 0.458,0.198 10 false GND 1.813,1.927 2.76,2.125 0.948,0.198 10 false 20 ms./DIV. 0.24,0.583 0.698,0.781 0.458,0.198 10 false CH1 0.063,0.063 0.76,0.26 0.698,0.198 10 false 5 V/DIV. 0.24,1.406 0.698,1.604 0.458,0.198 10 false CH2

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

G2+ stands for the cam position sensor signal, and NE+ stands for the crank position sensor signal

·

Grounding failure of the shielded wire may cause noise in the waveforms.



ECM Terminal Name CH1: Between G2+ and G2-
CH2: Between NE+ and NE-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

If there is no signal from the crank position sensor despite the crankshaft rotating, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Crank position sensor
Required Sensors/Components (Related) Cam position sensor
Frequency of Operation Continuous

COMPONENT OPERATING RANGE

Crank position sensor
·

Crank position sensor output voltage fluctuates while crankshaft revolving

·

34 crank position sensor signals per crankshaft revolution



CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine.

8.

Idle the engine for 20 seconds or more.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0335.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A268232E02
0.975,3.88 2.386,4.045 1.411,0.165 10 Crank Position Sensor 5.429,4.181 5.789,4.346 0.360,0.165 10 ECM 0.975,3.726 1.279,3.891 0.304,0.165 10 C11 5.073,2.833 5.255,2.975 0.181,0.142 10 78 4.994,3.405 5.254,3.547 0.260,0.142 10 110 5.378,2.892 5.673,3.041 0.295,0.149 10 NE+ 5.378,3.464 5.673,3.613 0.295,0.149 10 NE- 2.048,2.813 2.148,2.976 0.100,0.163 10 1 2.06,3.393 2.177,3.556 0.117,0.163 10 2 3.659,3.828 4.233,4.012 0.574,0.184 10 Shielded 5.08,1.048 5.262,1.190 0.181,0.142 10 82 5.001,1.633 5.261,1.775 0.260,0.142 10 114 5.378,1.12 5.812,1.269 0.434,0.149 10 VV1+ 5.378,1.691 5.777,1.840 0.399,0.149 10 VV1- 1.006,2.105 2.354,2.270 1.348,0.165 10 Cam Position Sensor 1.006,1.951 1.310,2.116 0.304,0.165 10 C13 2.05,1.024 2.151,1.187 0.100,0.163 10 1 2.062,1.604 2.179,1.766 0.117,0.163 10 2 0.178,4.176 0.893,4.338 0.715,0.163 10 *1: for LHD 0.178,4.438 0.920,4.601 0.743,0.163 10 *2: for RHD 5.429,4.014 6.339,4.177 0.909,0.163 10 C10*1, C9*2

CAUTION / NOTICE / HINT

HINT:
·

After performing the inspection procedure for the crank position sensor, if DTC P0335 is output again, check the following items related to the cam position sensor.

-

Installation condition of the cam position sensor

-

Installation condition of the camshaft

-

Connection of the cam position sensor connector


·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the intelligent tester. To perform the check, follow the procedures below:

(a)

Connect the intelligent tester to the DLC3.

(b)

Turn the power switch on (IG).

(c)

Turn the tester on.

(d)

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

(e)

Start the engine.

(f)

Turn the tester on.

(g)

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crank position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crank position sensor output voltage is insufficient.


·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.


g.

Read the values displayed on the tester while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the tester.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the tester remains at zero (0), there may be an open or short in the crank position sensor circuit.





OK

NG

2.INSPECT CRANK POSITION SENSOR (RESISTANCE)
2.INSPECT CRANK POSITION SENSOR (RESISTANCE)

OK

3.CHECK HARNESS AND CONNECTOR (CRANK POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANK POSITION SENSOR - ECM)
a.

Disconnect the crank position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C11-1 - C10-78 (NE+) Always Below 1 Ω
C11-2 - C10-110 (NE-) Always Below 1 Ω
C11-1 or C10-78 (NE+) - Body ground Always 10 kΩ or higher
C11-2 or C10-110 (NE-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C11-1 - C9-78 (NE+) Always Below 1 Ω
C11-2 - C9-110 (NE-) Always Below 1 Ω
C11-1 or C9-78 (NE+) - Body ground Always 10 kΩ or higher
C11-2 or C9-110 (NE-) - Body ground Always 10 kΩ or higher




OK

4.CHECK SENSOR INSTALLATION (CRANK POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANK POSITION SENSOR)
B319222E02
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

a.

Check the crank position sensor installation.

OK:

Crank position sensor is installed correctly.




OK

5.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE)

NG

5.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE)
a.

Inspect the teeth of the crank angle sensor plate.

OK:

Crank angle sensor plate does not have any cracks or deformation.




OK

NG