Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A78-121  Drive Motor "A" Inverter Performance  


DESCRIPTION

For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A78-266).

If an overvoltage occurs in the motor inverter or generator inverter, the MG ECU detects it and transmits this information to the power management control ECU.

HINT:

The term "drive motor A" indicates MG2.


DTC No. INF Code DTC Detection Condition Trouble Area
P0A78 121 Motor inverter overvoltage signal detection (overvoltage due to system malfunction)
·

Wire harness or connector

·

Hybrid battery junction block assembly

·

Inverter with converter assembly

·

Service plug grip (EV battery fuse)

·

Frame wire

·

Hybrid vehicle transaxle assembly

·

Motor cable

·

Power management control ECU

·

PCU fuse



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A1A-200 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200).

Refer to the wiring diagram for DTC P0AA6-526 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

Refer to the wiring diagram for DTC P324E-788 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P324E-788).

Refer to the wiring diagram for DTC U0110-159 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>U0110-159).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

With the vehicle engine stopped, the power switch on (READY) and the shift lever in P, depress the accelerator pedal to start the engine.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0A78-121 is set before any of the DTCs in the table below are set. A
Any of the DTCs in the table below are set before P0A78-121 is set. B


DTC No. Relevant Diagnosis
P0A9C-123 Hybrid Battery Temperature Sensor "A" Range / Performance
P0A9D-123 Hybrid Battery Temperature Sensor "A" Circuit Low
P0A9E-123 Hybrid Battery Temperature Sensor "A" Circuit High
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P0AC1-123 Hybrid Battery Pack Current Sensor Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor Circuit High
P0AC6-123 Hybrid Battery Temperature Sensor "B" Range / Performance
P0AC7-123 Hybrid Battery Temperature Sensor "B" Circuit Low
P0AC8-123 Hybrid Battery Temperature Sensor "B" Circuit High
P0ACB-123 Hybrid Battery Temperature Sensor "C" Range / Performance
P0ACC-123 Hybrid Battery Temperature Sensor "C" Circuit Low
P0ACD-123 Hybrid Battery Temperature Sensor "C" Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P3011-123, P3012-123, P3013-123, P3014-123, P3015-123, P3016-123, P3017-123, P3018-123, P3019-123, P3020-123 Battery Block # Becomes Weak
P3065-123 Hybrid Battery Temperature Sensor Range / Performance Stuck "A"
P308A-123 Hybrid Battery Voltage Sensor All Circuits Low

HINT:
·

Refer to the Freeze Frame data to determine the order in which the DTCs were set.

·

P0A78-121 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0A78-121 is output, or DTCs other than the ones in the table below are also output. A
Any of the following DTCs including pending DTCs are also output. B


DTC No. Relevant Diagnosis
P0A1A (all INF codes)*1 Generator Control Module
P0A1B (all INF codes)*1 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500 Drive Motor "A" Position Sensor Circuit Range / Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range / Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A60 (all INF codes)*1 Drive Motor "A" Phase V Current
P0A63 (all INF codes)*1 Drive Motor "A" Phase W Current
P0A72 (all INF codes)*1 Generator Phase V Current
P0A75 (all INF codes)*1 Generator Phase W Current
P0A78-113, 128, 266, 267, 279, 284, 286, 287, 306, 503, 504, 505, 506, 565, 586, 806, 807, 808 Drive Motor "A" Inverter Performance
P0A7A-122, 130, 322, 324, 325, 344, 517, 518, 809, 810, 811 Generator Inverter Performance
P0A90-509 Drive Motor "A" Performance
P0A92-521 Hybrid Generator Performance
P0A93-346 Inverter Cooling System Performance
P0A94-172, 442, 547, 548, 549, 553, 554, 555, 556, 557, 585, 587, 589, 590 DC / DC Converter Performance
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0C73-776 Motor Electronics Coolant Pump "A" Control Performance
P0C76-523 Hybrid Battery System Discharge Time Too Long
P3004-803 High Voltage Power Resource
P314A-828 Inverter Coolant Pump Speed Signal

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0A78-121 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

OK

5.CHECK GENERATOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK GENERATOR RESOLVER

OK

6.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

27.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

OK

7.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK MOTOR RESOLVER

OK

8.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)

NG

29.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
8.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)

A

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)

A

10.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

10.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

OK

11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

NG

34.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)
11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

12.CHECK INVERTER WITH CONVERTER ASSEMBLY (FRAME WIRE CONNECTOR CONNECTION CONDITION)

NG

36.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)
12.CHECK INVERTER WITH CONVERTER ASSEMBLY (FRAME WIRE CONNECTOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258645

Remove the inverter cover from the inverter with converter assembly.


d.
A258649E05
0.656,0.917 0.792,1.094 0.135,0.177 10 true A 1.865,0.615 2,0.792 0.135,0.177 10 true B 1.094,1.313 1.229,1.49 0.135,0.177 10 false A 0.813,0.177 0.948,0.354 0.135,0.177 10 true B

Check that the bolts for frame wire are tightened to the specified torque, the frame wire is connected securely, and there are no contact problems.

Specified Condition:
Bolt A:

T=8.0 N*m (82 kgf*cm, 71 in.*lbf)

Bolt B:

T=9.2 N*m (94 kgf*cm, 81 in.*lbf)


NOTICE:
·

Make sure that the tightening torque of the bolt A is between 6.4 and 9.6 N*m (65 and 98 kgf*cm, 57 and 85 in.*lbf).

·

Make sure that the tightening torque of the bolt B is between 6.4 and 12 N*m (65 and 122 kgf*cm, 57 and 106 in.*lbf).




e.

Disconnect the frame wire from the inverter with converter assembly.


f.

Check for arc marks at the bolts and terminals for the frame wire.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



g.

Connect the frame wire to the inverter with converter assembly.


h.

Install the inverter cover.


i.

Install the inverter terminal cover.



A

13.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

13.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Visually check the connection of the service plug grip to the HV battery. Remove the service plug grip and check for contamination.

OK:

Dirt or foreign objects have not entered the connection, and there is no evidence of contamination.




OK

14.INSPECT SERVICE PLUG GRIP

NG

14.INSPECT SERVICE PLUG GRIP
a.

Remove the service plug drip.


b.
A204559E01
0.125,0.098 0.318,0.263 0.193,0.165 10 *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Service plug grip terminals Always Below 1 Ω


Text in Illustration
*1 Service plug grip


c.

Install the service plug drip.



OK

15.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (FRAME WIRE CONNECTION CONDITION)

NG

15.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (FRAME WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
A267592

Check that the frame wire connectors are connected securely, and there are no contact problems.


d.

Disconnect the frame wire from the hybrid battery junction block assembly.


e.

Check for arc marks on the terminals of the frame wire.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Connect the frame wire to the hybrid battery junction block assembly.


g.

Install the No. 1 hybrid vehicle battery cover panel LH.



A

16.CHECK FRAME WIRE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

16.CHECK FRAME WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
A267592

Disconnect the frame wire from the hybrid battery junction block assembly.


d.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


e.
A258645

Remove the inverter cover from the inverter with converter assembly.


f.
A258649

Disconnect the frame wire from the inverter with converter assembly.


g.
U158989E02
2.073,1.771 2.344,1.771 false 1.094,1.771 1.365,1.771 false 1,3.479 1,3.198 false 1.833,3.469 1.833,3.188 false 2.198,4.125 2.448,3.917 false 0.542,1.052 0.74,1.229 0.198,0.177 10 false P1 0.896,2.615 1.094,2.792 0.198,0.177 10 false P5 1.74,2.604 1.938,2.781 0.198,0.177 10 false P4 0.167,0.146 0.375,0.344 0.208,0.198 10 false *a 0.167,2.323 0.375,2.521 0.208,0.198 10 false *b 2.406,1.688 2.708,1.865 0.302,0.177 10 false CBI 0.792,1.688 1.094,1.865 0.302,0.177 10 false CEI 0.875,3.5 1.177,3.677 0.302,0.177 10 false CBI 1.708,3.49 2.01,3.667 0.302,0.177 10 false CEI 2.01,4.073 2.313,4.25 0.302,0.177 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
P1-2 (CBI) - P5-1 (CBI) (Positive terminal) Power switch off Below 1 Ω
P1-1 (CEI) - P4-1 (CEI) (Negative terminal) Power switch off Below 1 Ω


Text in Illustration
*1 Shield Ground
*a Frame Wire
(Inverter with Converter Assembly Side)
*b Frame Wire
(Hybrid Battery Junction Block Assembly Side)


h.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
P5-1 (CBI) - Body ground and shielded ground Power switch off 10 MΩ or higher
P4-1 (CEI) - Body ground and shielded ground Power switch off 10 MΩor higher
P5-1 (CBI) - P4-1 (CEI) Power switch off 10 MΩ or higher



i.

Connect the frame wire to the hybrid battery junction block assembly.


j.

Connect the frame wire to the inverter with converter assembly.


k.

Install the No. 1 hybrid vehicle battery cover panel LH.


l.

Install the inverter cover.


m.

Install the inverter terminal cover.



OK

17.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

17.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS).


c.
A381346E02
0.521,0.698 0.833,0.802 false 2.979,1.427 2.74,1.219 false 0.979,2.802 1.219,2.521 false 1.604,2.823 1.344,2.521 false 0.094,0.094 0.438,0.354 0.344,0.26 10 false *a 0.229,0.615 0.573,0.875 0.344,0.26 10 false CBI 1.146,0.448 1.49,0.708 0.344,0.26 10 false P5 3.042,0.823 3.385,1.083 0.344,0.26 10 false A 3.031,1.406 3.375,1.667 0.344,0.26 10 false + 1.51,2.854 2.063,3.135 0.552,0.281 10 false SMRB 0.802,2.844 1.146,3.104 0.344,0.26 10 false GND 0.188,2.177 0.531,2.438 0.344,0.26 10 false M40

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (+) - P5-1 (CBI) Auxiliary battery voltage is not applied between terminals M40-1 (SMRB) and M40-2 (GND) 10 kΩ or higher
Auxiliary battery voltage is applied between terminals M40-1 (SMRB) and M40-2 (GND) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M40-1 (SMRB) - M40-2 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω



e.

Install the hybrid battery junction block assembly.



OK

18.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRG)

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

18.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRG)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS).


c.
A381347E02
0.802,0.958 1.25,0.667 false 2.708,1.479 2.958,1.146 false 0.896,2.833 1.073,2.552 false 1.406,2.844 1.229,2.531 false 1.302,0.552 1.625,0.813 0.323,0.26 10 false CEI 0.25,0.927 0.573,1.188 0.323,0.26 10 false P4 0.063,0.198 0.385,0.458 0.323,0.26 10 false *a 0.26,2.292 0.583,2.552 0.323,0.26 10 false M40 0.677,2.865 1.188,3.146 0.51,0.281 10 false SMRG 1.313,2.875 1.802,3.146 0.49,0.271 10 false GND 2.917,1.667 3.24,1.927 0.323,0.26 10 false c1 3.01,1.042 3.333,1.302 0.323,0.26 10 false -

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c1-1 (-) - P4-1 (CEI) Auxiliary battery voltage is not applied between terminals M40-3 (SMRG) and M40-2 (GND) 10 kΩ or higher
Auxiliary battery voltage is applied between terminals M40-3 (SMRG) and M40-2 (GND) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M40-3 (SMRG) - M40-2 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω



e.

Install the hybrid battery junction block assembly.



OK

19.CHECK FUSE (PCU)

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

19.CHECK FUSE (PCU)

OK

20.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

31.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)
20.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

OK

21.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

21.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

OK

22.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK POWER MANAGEMENT CONTROL ECU

OK

23.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

NG

23.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

24.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

NG

CONNECT SECURELY

24.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

25.CHECK FOR INTERMITTENT PROBLEMS

NG

CONNECT SECURELY

25.CHECK FOR INTERMITTENT PROBLEMS

OK

26.SIMULATION TEST

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

26.SIMULATION TEST
a.

Connect the intelligent tester to the DLC3.


b.

With the vehicle engine stopped, the power switch on (READY) and the shift lever in P, depress the accelerator pedal to start the engine.


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0A78-121 is output. A
P0A78-121 is not output. B


HINT:

If the connector engagement check and cleaning caused the condition to return to normal, DTCs will not be output.



e.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

END

27.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

28.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

NG

CONNECT SECURELY

28.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

29.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

30.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

NG

CONNECT SECURELY

30.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

31.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)

OK

32.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

33.REPAIR OR REPLACE HARNESS OR CONNECTOR
32.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NEXT

REPLACE FUSE (PCU)

33.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (PCU)

34.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)

A

35.CHECK MOTOR CABLE (FOR MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

36.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)

A

37.CHECK MOTOR CABLE (FOR MG2)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY