Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3004-800  High Voltage Power Resource  P3004-801  High Voltage Power Resource  


DESCRIPTION

Refer to the description for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

DTC No. INF Code DTC Detection Condition Trouble Area
P3004 800 Excessive overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on).
·

Wire harness or connector

·

No. 4 engine wire

·

Compressor with motor assembly

·

Inverter with converter assembly

·

Hybrid battery junction block assembly

·

Frame wire

·

Power management control ECU


801 Minimal overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on).

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A08-264 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A08-264).

Refer to the wiring diagram for DTC P0AA6-526 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).


CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs, perform the following procedure and check that the same DTC (including pending DTC) is not output.

1.

Turn the power switch off and wait for 30 seconds or more.

2.

Turn the power switch on (READY) and wait for 30 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P3004-800 or P3004-801 is output, or DTCs other than the ones in the table below are also output. A
DTCs shown in Table 1 are output simultaneously. B
DTCs shown in Table 2 are output simultaneously. C


Table 1
DTC No. Relevant Diagnosis
P0A09-265 DC/DC Converter Status Circuit Low Input
P0A10-263 DC/DC Converter Status Circuit High Input

Table 2
DTC No. Relevant Diagnosis
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P0AC1-123 Hybrid Battery Pack Current Sensor Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low
P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low
P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low
P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low
P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low
P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low
P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low
P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low
P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low
P0B6A-123 Hybrid Battery Voltage Sensor "J" Circuit Low
P0B6F-123 Hybrid Battery Voltage Sensor "K" Circuit Low
P308A-123 Hybrid Battery Voltage Sensor All Circuits Low
U029A-123 Lost Communication with Hybrid Battery Pack Sensor Module

HINT:

P3004-800 or P3004-801 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.



e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

B

C

2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

3.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

NG

CONNECT SECURELY

3.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258645

Remove the inverter cover from the inverter with converter assembly.


d.
U159098E03
1.427,1.26 1.708,1.438 0.281,0.177 10 false D2

Disconnect connector D2 of the No. 2 engine wire (air conditioning harness) from the inverter with converter assembly.


e.
U158857E01
1.627,1.81 2.050,1.978 0.424,0.168 10 ACPE 0.912,1.618 1.336,1.786 0.424,0.168 10 ACPB 0.119,0.083 0.310,0.263 0.191,0.180 10 *a 0.373,0.725 0.575,0.906 0.202,0.181 10 D2 1.817,1.215 1.817,1.764 false 1.422,1.214 1.139,1.581 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
(Tester Probe Polarity)
Switch Condition Specified Condition
D2-2 (ACPE) (Negative probe) - D2-1 (ACPB) (Positive probe) Power switch off 100 kΩ or higher


Text in Illustration
*a No. 2 Engine Wire (Air Conditioning Harness)
(Inverter with Converter Assembly Side)

NOTICE:
·

Do not use a megohmmeter.

·

Read the resistance after the value has stabilized.



HINT:

The polarities of the tester probes may differ depending on the tester. Use the current output probe of the tester as the positive probe for this measurement. To determine the polarity, use another voltmeter to confirm the current output probe of the tester. When measuring the output of the tester, the voltmeter positive probe indicates the tester current output probe.



f.

Connect the No. 2 engine wire (air conditioning harness) to the inverter with converter assembly.


g.

Install the inverter cover.


h.

Install the inverter terminal cover.



OK

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

NG

7.CHECK NO. 2 ENGINE WIRE
4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A38 from power management control ECU.


c.

Disconnect connector A47 from the inverter with converter assembly.


d.
A379054E03
1.208,1.938 1.604,2.188 0.396,0.25 0.875,2.26 1.135,2.542 false 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 1.281,1.979 1.594,2.177 0.313,0.198 10 false A38 1.177,2.479 1.917,2.76 0.74,0.281 10 false NODD

A379055E02
2.813,0.979 3.229,1.229 0.417,0.25 0.729,1.115 1.229,1.052 false 0.083,0.115 0.396,0.313 0.313,0.198 10 false *b 0.25,1.031 0.771,1.25 0.521,0.219 10 false NODD 2.906,1.021 3.219,1.219 0.313,0.198 10 false A47

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A47-12 (NODD) - A38-21 (NODD) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A47-12 (NODD) or A38-21 (NODD) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)


e.

Connect the inverter with converter assembly connector.


f.

Connect the power management control ECU connector.



OK

5.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POWER MANAGEMENT CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON (IG).


d.
U183254E02
0.865,1.844 0.958,2.438 false 1.823,1.698 2,2.438 false 0.667,1.021 0.938,1.188 0.271,0.167 10 false A38 0.135,0.188 0.406,0.354 0.271,0.167 10 false *a 1.948,1.021 2.271,1.188 0.323,0.167 10 false G57 0.719,2.458 1.156,2.635 0.438,0.177 10 false NODD 1.927,2.448 2.167,2.625 0.24,0.177 10 false E1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-21(NODD) - G57-6(E1) Ignition switch ON (IG) Less than 1.5 V


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.



OK

6.CHECK FRAME WIRE

NG

6.CHECK FRAME WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258645

Remove the inverter cover from the inverter with converter assembly.


d.
U158936E02
1.688,0.979 1.885,1.156 0.198,0.177 10 false P1

Disconnect connector P1 of the frame wire from the inverter with converter assembly.


e.
U158860E02
1.229,1.802 0.677,1.875 false 2.052,1.813 2.688,1.885 false 0.083,0.01 0.271,0.177 0.188,0.167 10 false *a 0.365,1.792 0.646,1.99 0.281,0.198 10 false CEI 2.729,1.802 3.01,2 0.281,0.198 10 false CBI 0.406,1.115 0.667,1.292 0.26,0.177 10 false P1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
P1-2 (CBI) - P1-1 (CEI) Power switch off 10 kΩ or higher


Text in Illustration
*a Frame Wire
(Inverter With Converter Assembly Side)


f.

Connect the frame wire.


g.

Install the inverter cover.


h.

Install the inverter terminal cover.



OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

8.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY
7.CHECK NO. 2 ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258645

Remove the inverter cover from the inverter with converter assembly.


d.
U159098E03
1.427,1.26 1.708,1.438 0.281,0.177 10 false D2

Disconnect connector D2 of the No. 2 engine wire (air conditioning harness) from the inverter with converter assembly.


e.
U159121E03
1.958,1.323 2.323,1.573 0.365,0.25 10 false D1

Disconnect connector D1 of the No. 2 engine wire (air conditioning harness) from the compressor with motor assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL).


f.
U158858E01
1.627,1.81 2.050,1.978 0.424,0.168 10 ACPE 0.912,1.618 1.336,1.786 0.424,0.168 10 ACPB 0.119,0.083 0.310,0.263 0.191,0.180 10 *a 0.371,0.725 0.574,0.906 0.202,0.181 10 D2 1.817,1.215 1.817,1.764 false 1.422,1.214 1.139,1.581 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
D2-1 (ACPB) - D2-2 (ACPE) Power switch off 10 kΩ or higher


Text in Illustration
*a No. 2 Engine Eire (Air Conditioning Harness)
(Inverter with Converter Assembly Side)


g.

Connect the No. 2 engine wire (air conditioning harness) to the compressor with motor assembly.


h.

Connect the No. 2 engine wire (air conditioning harness) to the inverter with converter assembly.


i.

Install the inverter cover.


j.

Install the inverter terminal cover.



OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPLACE NO. 2 ENGINE WIRE

8.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
U159050E03
1.531,0.302 1.917,0.594 0.385,0.292 10 false P5 1.365,1.063 1.76,1.344 0.396,0.281 10 false P4

Disconnect connector P5 and connector P4 of the frame wire from the hybrid battery junction block assembly.


d.
U159051E02
1.396,0.688 0.5,0.354 false 1.417,0.865 0.479,0.802 false 0.146,0.229 0.438,0.438 0.292,0.208 10 false CBI 0.135,0.708 0.385,0.917 0.25,0.208 10 false CEI 1.365,0.313 1.635,0.479 0.271,0.167 10 false P5 1.302,1 1.573,1.167 0.271,0.167 10 false P4

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
P4-1 (CEI) - P5-1 (CBI) Power switch off 10 kΩ or higher



e.

Connect the frame wire.


f.

Install the No. 1 hybrid vehicle battery cover panel LH.



OK

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY