Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › ENGINE UNIT › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277949 ENGINE UNIT A

1NZ-FXE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 2.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.
A269005

Remove the oil filler cap sub-assembly from the cylinder head cover.


Hide 12108A 3.REMOVE OIL FILLER CAP GASKET

a.
A065656E08
1.531,1.073 1.781,1.51 1.781,1.51 2.063,1.51 false 2.104,1.448 2.26,1.594 0.156,0.146 10 false *1

Using a screwdriver, remove the oil filler cap gasket from the oil filler cap.

Text in Illustration
*1 Protective Tape

HINT:

Wrap the screwdriver tip with protective tape before use.



Hide 11452 4.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 11101E 5.REMOVE CAMSHAFT POSITION SENSOR

a.
A266999

Remove the bolt and camshaft position sensor.


b.
A412347C01
1.781,1.885 1.781,1.563 false 1.729,1.896 2.042,2.052 0.313,0.156 10 false *1
*1 O-ring


Remove the O-ring from the camshaft position sensor.

NOTICE:
·

Make sure to only remove the O-ring with bare hands.

·

When removing the O-ring, be careful not to damage the O-ring groove of the camshaft position sensor.

·

If the O-ring groove of the camshaft position sensor is damaged, replace the camshaft position sensor with a new one.




Hide 11101J 6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

a.
A266998

Remove the bolt and camshaft timing oil control valve assembly.


b.
A195062E09
1.081,0.414 1.234,0.560 0.153,0.146 10 *1 1.602,0.876 1.418,0.493 1.418,0.493 1.265,0.493 false

Remove the O-ring from the camshaft timing oil control valve assembly.


Hide 89615 7.REMOVE KNOCK CONTROL SENSOR

a.
A268026

Remove the bolt and knock control sensor.


Hide 89422 8.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

a.
A275780

Using a 19 mm union nut wrench, remove the engine coolant temperature sensor and gasket.


Hide 83530 9.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

a.
A268027

Using a 24 mm deep socket wrench, remove the engine oil pressure switch assembly.


Hide 15100Q 11.REMOVE CRANKSHAFT POSITION SENSOR

a.
A269006

Remove the bolt and crankshaft position sensor.


b.
A413178C02
1.656,1.896 1.656,1.469 false 1.656,4.01 1.656,3.583 false 0.208,0.292 0.542,0.573 0.333,0.281 12 false *A 0.229,2.375 0.656,2.75 0.427,0.375 12 false *B 1.594,1.917 1.906,2.073 0.313,0.156 10 false *1 1.594,4.01 1.906,4.167 0.313,0.156 10 false *1
*A for Type A
*B for Type B
*1 O-ring


Remove the O-ring from the crankshaft position sensor.

NOTICE:
·

Make sure to only remove the O-ring with bare hands.

·

When removing the O-ring, be careful not to damage the O-ring groove of the crankshaft position sensor.

·

If the O-ring groove of the crankshaft position sensor is damaged, replace the crankshaft position sensor with a new one.




Hide 16031 12.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

a.
A267959

Remove the 2 bolts and water inlet with thermostat sub-assembly.


b.
A267962

Remove the gasket from the water inlet with thermostat sub-assembly.


Hide 16100 13.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A267965

Remove the 5 bolts and engine water pump assembly.


b.
A267966

Remove the gasket from the engine water pump assembly.


Hide 16323 14.REMOVE WATER INLET HOUSING

a.
A266948

Remove the bolt, 2 nuts and water inlet housing.


b.

Remove the gasket.


Hide 12315A 15.REMOVE ENGINE MOUNTING BRACKET RH

Hide 12204 16.REMOVE VENTILATION VALVE SUB-ASSEMBLY

a.
A269007

Using a 19 mm deep socket wrench, remove the ventilation valve sub-assembly from the cylinder head cover sub-assembly.


Hide 11201 17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A265764

Remove the 9 bolts, 2 seal washers, 2 nuts and cylinder head cover sub-assembly.


b.

Remove the gasket from the cylinder head cover sub-assembly.


Hide 13407 18.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY

a.

Set the No. 1 cylinder to TDC/compression.

i.

Turn the crankshaft damper until its notch and timing mark "0" of the timing chain cover are aligned.


ii.
A268183E02
0.875,0.552 0.344,0.552 true 2.5,0.594 3.177,0.594 true 2.448,1.188 3.021,1.188 true 1.594,0.958 1.594,1.656 1.594,1.656 0.333,1.656 true 0.563,1.021 0.563,1.656 true 2.313,2.833 2.76,2.833 true 3.063,1.104 3.219,1.26 0.156,0.156 10 true *a 3.188,0.5 3.344,0.656 0.156,0.156 10 true *a 0.156,0.448 0.313,0.604 0.156,0.156 10 true *b 0.156,1.563 0.313,1.719 0.156,0.156 10 false *c 2.771,2.75 2.927,2.906 0.156,0.156 10 false *d

Check that the timing marks on both the camshaft timing sprocket and the camshaft timing gear are facing upward as shown in the illustration.

Text in Illustration
*a Timing Mark
*b Timing Mark (Rectangle)
*c Mark (Circle)
*d Timing Notch

HINT:
·

There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.

·

If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.





b.
A267009E01
0.192,0.805 0.506,0.961 0.314,0.156 10 SST 2.209,1.796 2.523,1.952 0.314,0.156 10 SST 1.019,0.895 0.56,0.895 false 1.615,1.253 1.904,1.88 1.904,1.88 2.194,1.88 false

Using SST, hold the crankshaft damper sub-assembly in place and loosen the bolt.

SST
09213-58012  (91111-50845)
09330-00021  

NOTICE:

When installing SST, be careful that the bolt which holds SST does not interfere with the chain cover.



c.
A267010E01
0.125,0.617 0.424,0.772 0.299,0.155 10 SST 0.917,0.996 0.684,0.703 0.684,0.703 0.483,0.703 false

Using SST, remove the crankshaft damper sub-assembly and bolt.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05021)

HINT:

Apply a lubricant to the threads and end of SST.



d.
A265784

Remove the crankshaft straight pin.


Hide 23814B 26.REMOVE FUEL DELIVERY PIPE

a.
A266997

Remove the 3 bolts and fuel delivery pipe.


Hide 23891 27.REMOVE FUEL DELIVERY SPACER

Hide 23291 28.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250 29.REMOVE FUEL INJECTOR ASSEMBLY

Hide 13512 30.REMOVE NO. 2 CAMSHAFT

a.
U159032E04
0.979,1.781 1.104,1.927 0.125,0.146 10 false 1 2.344,0.156 2.604,0.354 0.26,0.198 10 false 2 1.24,0.156 1.5,0.375 0.26,0.219 10 false 5 0.677,0.156 0.969,0.385 0.292,0.229 10 false 3 1.792,0.156 2.167,0.427 0.375,0.271 10 false 4

Using several steps, uniformly loosen and remove the 11 bolts in the sequence shown in the illustration. Then remove the No. 1 camshaft bearing cap and 4 No. 2 camshaft bearing caps.

NOTICE:

Uniformly loosen the bolts while keeping the No. 2 camshaft level.



Hide 13523 31.REMOVE CAMSHAFT TIMING GEAR OR SPROCKET

a.
A064874

Clamp the No. 2 camshaft in a vise.

NOTICE:

Be careful not to damage the No. 2 camshaft.



b.

Remove the bolt and camshaft timing gear or sprocket.


Hide 13511 32.REMOVE CAMSHAFT

a.
U159031E03
1.031,1.781 1.156,1.927 0.125,0.146 10 false 2 1.583,1.781 1.708,1.927 0.125,0.146 10 false 4 2.135,1.781 2.26,1.927 0.125,0.146 10 false 3 2.667,1.781 2.792,1.927 0.125,0.146 10 false 1

Using several steps, uniformly loosen and remove the 8 bolts in the sequence shown in the illustration. Then remove the 4 No. 2 camshaft bearing caps.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



Hide 13050 33.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13050 34.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 15600A 37.REMOVE OIL FILTER UNION

a.
A269008

Using a 12 mm hexagon socket wrench, remove the oil filter union.


Hide 12102A 38.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A265785

Remove the oil pan drain plug and gasket.


b.

Remove the 9 bolts and 2 nuts.


c.
A088894

Insert the blade of an oil pan seal cutter between the oil pan and No. 2 oil pan sub-assembly, cut the sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:

Be careful not to damage the oil pan and No. 2 oil pan sub-assembly.



Hide 15104 39.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A084113

Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.


Hide 12101 40.REMOVE OIL PAN SUB-ASSEMBLY

a.
A265814

Loosen and remove the 13 bolts uniformly in several steps.


b.
A265786E01
0.822,1.626 0.976,1.777 0.153,0.151 10 *1 0.908,0.87 0.908,1.612 false

Using a screwdriver, remove the oil pan sub-assembly by prying between the cylinder block and oil pan sub-assembly.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the contact surfaces of the oil pan sub-assembly and cylinder block.


HINT:

Wrap the screwdriver tip with protective tape before use.



c.
A088897

Remove the 2 O-rings from the cylinder block.


d.
A089042

Using an E5 "TORX" socket wrench, remove the 4 stud bolts.


Hide 11401L 41.REMOVE REAR ENGINE OIL SEAL

a.
A089043

Remove the rear engine oil seal.