Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2013.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1249/49  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU receives the stop light switch assembly signal and detects the brake pedal operation status.

The skid control ECU has an open detection circuit, which stores this DTC if it detects an open in the stop light input line or ground line of the stop light circuit with the stop light switch assembly off (brake pedal not depressed).

DTC No. INF Code DTC Detection Condition Trouble Area
C1249/49 231 When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Stop light circuit



WIRING DIAGRAM

C411883E02
1.406,1.104 1.823,1.271 0.417,0.167 10 false STOP 6.125,1.854 6.563,2.01 0.438,0.156 10 false STP0 5.885,2.708 6.083,2.875 0.198,0.167 10 false 33 5.958,1.75 6.146,1.917 0.188,0.167 10 false 3 2.552,0.823 2.677,0.99 0.125,0.167 10 false 7 6.125,0.938 6.552,1.094 0.427,0.156 10 false STP2 1.125,1.958 2.521,2.146 1.396,0.188 10 false from Auxiliary Battery 2.76,3.396 3.094,3.563 0.333,0.167 10 false A32 3.073,3.396 4.229,3.75 1.156,0.354 10 false Stop Light Switch Assembly 4.625,4.896 4.948,5.052 0.323,0.156 10 false A41 4.938,4.896 7.063,5.26 2.125,0.365 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.281,2.667 4.406,2.833 0.125,0.167 10 false 1 3.042,4.365 4.344,4.552 1.302,0.188 10 false to Stop Light Circuit 5.958,0.823 6.156,0.99 0.198,0.167 10 false 6 6.125,2.781 6.552,2.938 0.427,0.156 10 false STP 2.552,2.667 2.667,2.833 0.115,0.167 10 false 2 4.281,0.823 4.469,0.99 0.188,0.167 10 false 3 4.281,1.75 4.406,1.917 0.125,0.167 10 false 4 2.729,2.792 3.146,2.958 0.417,0.167 10 false GND 2.729,0.948 2.844,1.115 0.115,0.167 10 false B 4.094,0.938 4.188,1.104 0.094,0.167 10 false L 3.885,1.875 4.25,2.042 0.365,0.167 10 false ACC 3.885,2.781 4.25,2.948 0.365,0.167 10 false OUT

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.


Result:
Result Proceed to
All stop lights illuminate when the brake pedal is depressed and turn off when the brake pedal is released. A
All stop lights do not illuminate when the brake pedal is depressed. B
One or more stop lights illuminate when the brake pedal is depressed but remain on when the brake pedal is released. C



A

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)

B

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT)

C

6.CHECK STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check the value of Stop Light SW when the brake pedal is depressed.


Result:
Result Proceed to
The value of Stop Light SW is ON. A
Other than above. B



A

3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION

B

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION
a.

Turn the power switch off (lock).


b.
C400630N01
1.51,0.396 1.865,0.635 0.354,0.24 2.323,1.635 2.063,1.125 true 1.563,0.438 2.021,0.635 0.458,0.198 10 false A32 0.198,0.167 0.656,0.365 0.458,0.198 10 false *a 2.24,1.656 2.698,1.854 0.458,0.198 10 false OUT

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A32-1 (OUT) - Body ground
·

Power switch on (IG)

·

The headlights are on

·

The blower motor switch is in the HI position

·

The rear window defogger is turned on

·

Stop light switch assembly off (Brake pedal released)


1.5 V or less


Text in Illustration
*a Component with harness connected
(Stop Light Switch Assembly)



OK

4.CLEAR DTC

NG

6.CHECK STOP LIGHT SWITCH ASSEMBLY
4.CLEAR DTC
a.

Turn the power switch off (lock).




NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Turn the power switch off (lock).


b.

Turn the power switch on (ready).


c.

Perform a road test.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1249/49 is not output. A
DTC C1249/49 is output (for LHD). B
DTC C1249/49 is output (for RHD). C




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

6.CHECK STOP LIGHT SWITCH ASSEMBLY
a.
C415043N01
1.375,0.281 1.906,0.552 0.531,0.271 1.104,1.188 0.823,1.75 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.531,0.333 1.99,0.49 0.458,0.156 10 false A32 0.667,1.76 1.083,1.958 0.417,0.198 10 false OUT

Turn the power switch off (lock).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A32-1 (OUT) - Body ground Stop light switch assembly off
(Brake pedal released)
1.5 V or less


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

7.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
7.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.
C415043N01
1.375,0.281 1.906,0.552 0.531,0.271 1.104,1.188 0.823,1.75 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.531,0.333 1.99,0.49 0.458,0.156 10 false A32 0.667,1.76 1.083,1.958 0.417,0.198 10 false OUT

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A32-1 (OUT) - Body ground Stop light switch assembly off
(Brake pedal released)
1.5 V or less


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

8.CHECK FOR SHORT TO +B IN STP CIRCUIT
8.CHECK FOR SHORT TO +B IN STP CIRCUIT
a.

Check that there is no short to +B in the STP circuit (wire harnesses, connectors and stop lights).

OK:

No short to +B.




OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the power switch off (lock).


b.
U183557E01
0.196,0.187 0.401,0.345 0.205,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 1.566,2.121 1.084,2.676 false 0.96,2.719 1.318,2.877 0.357,0.158 10 STP

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-33 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT)
a.

Check that there is no open in the wire harnesses and connectors from terminal OUT of the stop light switch assembly to the stop lights.

OK:

No open.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR