Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2014.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1345/66  Linear Solenoid Valve Offset Learning Undone  C1368/67  Linear Solenoid Valve Offset Malfunction  


DESCRIPTION

The skid control ECU stores and corrects the individual differences in the brake pedal stroke sensor assembly, actuator solenoids, and stroke simulator solenoid. Perform initialization and calibration of the linear solenoid valve if any of these parts is replaced.

The skid control ECU receives the shift position P signal from the hybrid vehicle control ECU through the CAN communication system.

The DTCs are cleared when the linear valve offset learning results are normal.

DTC No. INF Code DTC Detection Condition Trouble Area
C1345/66 - Linear valve offset learning undone. Perform linear valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal.
C1368/67 - Offset learned value out of specification.
·

Perform linear valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

Brake actuator (Brake booster with master cylinder assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


HINT:

When C1451/72 is output together with C1345/66 and/or C1368/67, inspect and repair the trouble areas indicated by C1451/72 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1451/72).


PROCEDURE

1.CHECK DTC

b.

Turn the power switch off (lock).


c.

Turn the power switch on (IG).


d.

Check the DTCs (electronically controlled brake system and hybrid control system) that are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR for the electronically controlled brake system, or Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR for the hybrid control system).

Result:
Result Proceed to
DTCs (except C1345/66, C1368/67 and hybrid control system DTC) are not output. A
Hybrid control system DTC is output. B
DTCs (except C1345/66 and/or C1368/67) are output. C


HINT:

Before performing initialization and calibration of the linear solenoid valve, C1203/95 will be output.




A

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE

B

C

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE
a.

Turn the power switch off (lock).


b.

Perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Turn the power switch on (IG).


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1345/66 and C1368/67 are not output. A
DTCs C1345/66 and/or C1368/67 are output (for LHD). B
DTCs C1345/66 and/or C1368/67 are output (for RHD). C




A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY