Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2014.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Slip Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

If the skid control ECU stores a DTC, the slip indicator light comes on in the combination meter assembly.

The slip indicator light blinks during ABS, VSC and/or TRC operation.

When the system fails, the slip indicator light comes on to warn the driver (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DIAGNOSIS SYSTEM).

WIRING DIAGRAM

C239015E29
5,3.927 7.115,4.271 2.115,0.344 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.688,3.927 5,4.083 0.313,0.156 10 false A41 0.385,3.927 1.656,4.271 1.271,0.344 10 false Combination Meter Assembly 0.115,3.938 0.323,4.094 0.208,0.156 10 false G1 5.969,1.125 6.417,1.281 0.448,0.156 10 false CA1L 5.969,3.125 6.417,3.281 0.448,0.156 10 false CA1H 5.698,1.01 5.917,1.167 0.219,0.156 10 false 38 5.698,3.021 5.917,3.177 0.219,0.156 10 false 37 0.885,1.125 1.333,1.281 0.448,0.156 10 false CANL 0.885,3.125 1.333,3.281 0.448,0.156 10 false CANH 1.396,1.01 1.615,1.167 0.219,0.156 10 false 32 1.396,3.021 1.615,3.177 0.219,0.156 10 false 31

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK AUXILIARY BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (ready) 11 to 15.5 V




OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

CHARGE OR REPLACE AUXILIARY BATTERY

4.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


b.

Check the combination meter assembly.

OK:

The slip indicator light turns on or off in accordance with intelligent tester operation.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE COMBINATION METER ASSEMBLY