Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2013.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1271/71  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272/72  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1464/31  Front Speed Sensor RH Circuit  C1465/32  Front Speed Sensor LH Circuit  


DESCRIPTION

The speed sensor detects wheel speed and sends signals to the skid control ECU. These signals are used for ABS control.

DTCs C1271/71 and C1272/72 can be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1271/71 and C1272/72 are output only in Test Mode.

F100269E25
1.542,1.083 1.542,0.552 1.542,0.552 1.396,0.552 false 0.448,0.458 1.375,0.656 0.927,0.198 10 false Speed Sensor 1.146,2.167 2.438,2.365 1.292,0.198 10 false Speed Sensor Rotor 6.365,1.313 6.729,1.51 0.365,0.198 10 false 1.4 V 6.365,1.677 6.729,1.875 0.365,0.198 10 false 0.7 V 4.292,2.115 5.292,2.406 1,0.292 10 false Low speed 5.219,2.135 5.979,2.365 0.76,0.229 10 false High speed

DTC No. INF Code DTC Detection Condition Trouble Area
C1464/31 501 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Front speed sensor RH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 502 A malfunction occurs in 2 or more wheels. ↑
↑ 503 An open is detected in the speed sensor signal circuit for 0.05 seconds or more.
·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Front speed sensor RH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 504 Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Front speed sensor RH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 506 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.
·

Open or short in wire harness

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 507 While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Front speed sensor RH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 508 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.
·

Open or short in wire harness

·

Skid control ECU (Brake booster with master cylinder assembly)


C1465/32 511 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Front speed sensor LH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 512 A malfunction occurs in 2 or more wheels. ↑
↑ 513 An open is detected in the speed sensor signal circuit for 0.05 seconds or more.
·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Front speed sensor LH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 514 Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Front speed sensor LH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 516 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.
·

Open or short in wire harness

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 517 While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Front speed sensor LH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 518 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.
·

Open or short in wire harness

·

Skid control ECU (Brake booster with master cylinder assembly)


C1271/71
C1272/72
- Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Sensor installation

·

Front speed sensor rotor RH/LH (Front axle hub bearing RH/LH)



HINT:
·

DTCs C1464/31 and C1271/71 are for the front speed sensor RH.

·

DTCs C1465/32 and C1272/72 are for the front speed sensor LH.



WIRING DIAGRAM

C209842E24
1.365,1.469 2.885,1.635 1.521,0.167 10 false Front Speed Sensor RH 1.396,1 1.51,1.167 0.115,0.167 10 false 2 2.302,1 2.417,1.167 0.115,0.167 10 false 1 1.281,3.417 2.802,3.583 1.521,0.167 10 false Front Speed Sensor LH 1.396,2.979 1.51,3.146 0.115,0.167 10 false 2 2.302,2.979 2.417,3.146 0.115,0.167 10 false 1 5.771,3.979 7.052,4.719 1.281,0.74 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.729,0.99 5.906,1.135 0.177,0.146 10 false 5 5.99,0.552 6.281,0.698 0.292,0.146 10 false FR+ 5.667,0.427 5.844,0.573 0.177,0.146 10 false 18 5.99,1.125 6.281,1.271 0.292,0.146 10 false FR- 5.688,2.958 5.865,3.104 0.177,0.146 10 false 32 5.99,2.531 6.333,2.677 0.344,0.146 10 false FL+ 5.698,2.396 5.875,2.542 0.177,0.146 10 false 31 5.99,3.063 6.24,3.208 0.25,0.146 10 false FL- 1.01,1.479 1.375,1.646 0.365,0.167 10 false A21 0.948,3.417 1.313,3.583 0.365,0.167 10 false A22 3.76,1.542 4.427,1.708 0.667,0.167 10 false Shielded 3.76,3.51 4.427,3.677 0.667,0.167 10 false Shielded 5.448,4 5.719,4.146 0.271,0.146 10 false A41 1.552,3.083 1.885,3.229 0.333,0.146 10 false FL+ 2,3.083 2.25,3.229 0.25,0.146 10 false FL- 1.552,1.135 1.844,1.281 0.292,0.146 10 false FR+ 2,1.135 2.292,1.281 0.292,0.146 10 false FR-

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruptions in the wire harness and connector corresponding to a DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
FL Speed Open Front speed sensor LH open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-

OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.




OK

2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)
a.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


b.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the intelligent tester is similar to the speed indicated on the speedometer.




OK

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the power switch off (lock).


b.

Perform the sensor check in the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are cleared.




OK

4.RECONFIRM DTC

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Turn the power switch on (ready).


d.

Perform a road test.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1464/31 and C1465/32 are not output. A
DTCs C1464/31 and/or C1465/32 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

10.REPLACE FRONT SPEED SENSOR
5.CHECK FRONT SPEED SENSOR INSTALLATION
a.
C144929E77
0.833,1.625 0.833,0.667 0.833,0.667 0.969,0.667 false 0.708,2.479 0.906,2.802 0.906,2.802 1.052,2.802 false 0.625,2.885 0.906,3.083 0.281,0.198 10 false OK 2.656,2.917 2.979,3.115 0.323,0.198 10 false NG 1.115,2.719 2.031,2.917 0.917,0.198 10 false No clearance 1.031,0.594 1.573,0.792 0.542,0.198 10 false 8.5 N*m 0.115,0.063 1.563,0.26 1.448,0.198 10 false Front Speed Sensor:

Turn the power switch off (lock).


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)




OK

6.CHECK FRONT SPEED SENSOR TIP

NG

6.CHECK FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).




OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Install the front speed sensor.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector and the front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A41-18 (FR+) - A21-2 (FR+) Always Below 1 Ω
A41-18 (FR+) - Body ground Always 10 kΩ or higher
A41-5 (FR-) - A21-1 (FR-) Always Below 1 Ω
A41-5 (FR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A41-31 (FL+) - A22-2 (FL+) Always Below 1 Ω
A41-31 (FL+) - Body ground Always 10 kΩ or higher
A41-32 (FL-) - A22-1 (FL-) Always Below 1 Ω
A41-32 (FL-) - Body ground Always 10 kΩ or higher




OK

8.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.
C363121E01
0.167,1.25 0.583,1.5 0.417,0.25 1.75,1.25 2.167,1.5 0.417,0.25 1.177,2.75 1.031,2.281 false 2.771,2.75 2.625,2.281 false 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 0.25,1.292 0.563,1.49 0.313,0.198 10 false A21 1.125,2.781 1.5,2.979 0.375,0.198 10 false FR+ 1.823,1.292 2.135,1.49 0.313,0.198 10 false A22 2.698,2.781 3.073,2.979 0.375,0.198 10 false FL+

Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Condition Specified Condition
A21-2 (FR+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH:
Tester Connection Condition Specified Condition
A22-2 (FL+) - Body ground Power switch on (IG) 5.7 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Front Speed Sensor)

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

9.RECONFIRM DTC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.RECONFIRM DTC
a.

Turn the power switch off (lock).


b.

Reconnect the front speed sensor connector.



d.

Turn the power switch on (ready).


e.

Perform a road test.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1464/31 and/or C1465/32 are output. A
DTCs C1464/31 and C1465/32 are not output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

10.REPLACE FRONT SPEED SENSOR

B

10.REPLACE FRONT SPEED SENSOR
a.

Turn the power switch off (lock).




NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC

b.

Turn the power switch on (ready).


c.

Perform a road test.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1464/31 and/or C1465/32 are output. A
DTCs C1464/31 and C1465/32 are not output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

12.REPLACE FRONT AXLE HUB BEARING

B

END

12.REPLACE FRONT AXLE HUB BEARING
a.

Turn the power switch off (lock).


b.

Replace the front speed sensor rotor (front axle hub bearing) (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).

HINT:

The front speed sensor rotor is incorporated into the front axle hub bearing.

If the front speed sensor rotor needs to be replaced, replace the front axle hub bearing.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).




NEXT

13.RECONFIRM DTC
13.RECONFIRM DTC

b.

Turn the power switch on (ready).


c.

Perform a road test.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1464/31 and/or C1465/32 are output (for LHD). A
DTCs C1464/31 and/or C1465/32 are output (for RHD). B
DTCs C1464/31 and C1465/32 are not output. C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

END