The speed sensor detects wheel speed and sends signals to the skid control ECU. These signals are used for ABS control.
DTCs C1273/73 and C1274/74 can be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1273/73 and C1274/74 are output only in Test Mode.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1466/33 | 521 | While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Rear speed sensor RH ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 522 | A malfunction occurs in 2 or more wheels. | ↑ |
| ↑ | 523 | An open is detected in the speed sensor signal circuit for 0.05 seconds or more. | ·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Rear speed sensor RH ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 524 | Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Rear speed sensor RH ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 526 | When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more. | ·
Open or short in wire harness ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 527 | While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Rear speed sensor RH ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 528 | When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more. | ·
Open or short in wire harness ·
Skid control ECU (Brake booster with master cylinder assembly) |
| C1467/34 | 531 | While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Rear speed sensor LH ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 532 | A malfunction occurs in 2 or more wheels. | ↑ |
| ↑ | 533 | An open is detected in the speed sensor signal circuit for 0.05 seconds or more. | ·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Rear speed sensor LH ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 534 | Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Rear speed sensor LH ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 536 | When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more. | ·
Open or short in wire harness ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 537 | While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more. | ·
Open or short in speed sensor ·
Improperly installed speed sensor, or abnormal clearance between sensor and rotor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Rear speed sensor LH ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 538 | When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more. | ·
Open or short in wire harness ·
Skid control ECU (Brake booster with master cylinder assembly) |
| C1273/73
C1274/74 |
- | Detected only during Test Mode. | ·
Rear speed sensor RH/LH ·
Sensor installation ·
Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) |
DTCs C1466/33 and C1273/73 are for the rear speed sensor RH.
DTCs C1467/34 and C1274/74 are for the rear speed sensor LH.
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
Using the intelligent tester, check for any momentary interruptions in the wire harness and connector corresponding to a DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Speed Open | Rear speed sensor RH open detection / Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| RL Speed Open | Rear speed sensor LH open detection / Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
There are no momentary interruptions.
Perform the above inspection before removing the sensor and connector.
OK
NG
Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Wheel Speed | Rear speed sensor RH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear speed sensor LH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Check the speed value output from the speed sensor displayed on the intelligent tester.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).
The speed value output from the speed sensor displayed on the intelligent tester is similar to the speed indicated on the speedometer.
OK
NG
Turn the power switch off (lock).
Perform the sensor check in the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
All Test Mode DTCs are cleared.
OK
NG
Turn the power switch off (lock).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Perform a road test.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1466/33 and C1467/34 are not output. | A |
| DTCs C1466/33 and/or C1467/34 are output. | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Turn the power switch off (lock).
Check the speed sensor installation.
There is no clearance between the sensor and rear axle carrier.
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the rear speed sensor connector and the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W1-2 (RR+) - WM1-1 (RR+) | Always | Below 1 Ω |
| W1-2 (RR+) - WM1-2 (RR-) | Always | 10 kΩ or higher |
| W1-2 (RR+) - Body ground | Always | 10 kΩ or higher |
| W1-1 (RR-) - WM1-2 (RR-) | Always | Below 1 Ω |
| W1-1 (RR-) - WM1-1 (RR+) | Always | 10 kΩ or higher |
| W1-1 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X1-2 (RL+) - XM1-1 (RL+) | Always | Below 1 Ω |
| X1-2 (RL+) - XM1-2 (RL-) | Always | 10 kΩ or higher |
| X1-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| X1-1 (RL-) - XM1-2 (RL-) | Always | Below 1 Ω |
| X1-1 (RL-) - XM1-1 (RL+) | Always | 10 kΩ or higher |
| X1-1 (RL-) - Body ground | Always | 10 kΩ or higher |
| *A | for RH |
| *B | for LH |
| *a | Front view of skid control sensor wire |
| *b | Front view of wire harness connector
(to Sensor Side Connector) |
| *c | Front view of wire harness connector
(to Vehicle Side Connector) |
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-22 (RR+) - WM1-1 (RR+) | Always | Below 1 Ω |
| A41-22 (RR+) - Body ground | Always | 10 kΩ or higher |
| A41-9 (RR-) - WM1-2 (RR-) | Always | Below 1 Ω |
| A41-9 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-20 (RL+) - XM1-1 (RL+) | Always | Below 1 Ω |
| A41-20 (RL+) - Body ground | Always | 10 kΩ or higher |
| A41-7 (RL-) - XM1-2 (RL-) | Always | Below 1 Ω |
| A41-7 (RL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| WM1-1 (RR+) - Body ground | Power switch on (IG) | 5.7 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| XM1-1 (RL+) - Body ground | Power switch on (IG) | 5.7 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control Sensor Wire) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Turn the power switch off (lock).
Reconnect the rear speed sensor connector and the skid control sensor wire.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Perform a road test.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1466/33 and/or C1467/34 are output. | A |
| DTCs C1466/33 and C1467/34 are not output. | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Turn the power switch off (lock).
Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Perform a road test.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1466/33 and/or C1467/34 are output (for LHD). | A |
| DTCs C1466/33 and/or C1467/34 are output (for RHD). | B |
| DTCs C1466/33 and C1467/34 are not output. | C |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
B
C